The 2016 Odyssey uses a cartridge-style oil filter mounted on top of the engine
Your 2016 Honda Odyssey's oil filter is not a spin-on canister like you might find on a truck. Instead, it's a cartridge filter housed in a plastic cap on the top of the engine. The filter element itself sits inside that cap, and when you change your oil, you remove the cap, replace the filter cartridge, and reinstall the cap. This design is common on modern Honda engines and takes about five minutes once you have the car safely supported and the old oil drained.
The filter cap is located on the driver's side of the engine, toward the front. You'll see a large black plastic cylinder with a center bolt on top—that's your filter housing. The bolt is what you turn to remove the cap and access the cartridge inside. Knowing exactly where it sits saves you time when you're under the hood and prevents you from hunting for it while the engine is still warm.
Key Takeaways
- The 2016 Odyssey uses a cartridge-style oil filter in a cap on top of the engine, not a traditional spin-on filter.
- You will need a 74 mm oil filter wrench (or a strap wrench) to remove the filter cap, a new cartridge filter, and a new rubber O-ring seal.
- The correct replacement filter cartridge is Honda part number 15400-PLM-A02 or equivalent, and the O-ring is part number 91301-PLM-003.
- Always replace the O-ring when you change the filter, because a dry or damaged seal will cause oil leaks and pressure loss.
- Tighten the filter cap by hand after seating the new O-ring, then turn it an additional three-quarters of a turn with the wrench—over-tightening cracks the plastic housing.
What you need to buy and where to find it
The filter cartridge itself is Honda part number 15400-PLM-A02. You can order this directly from a Honda dealer, or you can buy an equivalent aftermarket cartridge from any auto parts store. Common brands like Fram, Mobil 1, and Bosch all make cartridge filters that fit the 2016 Odyssey. The part costs between $8 and $15 depending on the brand and where you shop. Do not skip the O-ring—it's part number 91301-PLM-003 and costs $2 to $4. A dried-out or pinched O-ring is the most common reason for oil leaks after a filter change, and replacing it takes no extra time.
You will also need a 74 mm oil filter wrench to remove the cap. This is a socket-like tool that grips the cap so you can turn it without stripping the plastic. A 74 mm wrench costs $10 to $20 new, but many auto parts stores will lend you one free if you buy the filter from them. If you don't have a 74 mm wrench and can't borrow one, a rubber strap wrench (the kind with a rubber band that grips round objects) works in a pinch, though it's slower and requires more hand strength.
Step-by-step removal and installation
Start with the engine cold or only warm to the touch. Locate the filter cap on the driver's side of the engine—it's the large black plastic cylinder with a bolt on top. Slide the 74 mm wrench over the cap and turn it counterclockwise to loosen it. Once it's loose enough, you can unscrew it by hand. The cap will come off with the old filter cartridge still inside it. Tip the cap over a drain pan or old container, because there will be oil inside.
Pull the old cartridge out of the cap and set it aside. Wipe the inside of the cap clean with a lint-free cloth or paper towel. Look at the rubber O-ring that sits in the groove at the bottom of the cap—this is the seal that keeps oil from leaking out. Remove the old O-ring and throw it away. Slide the new O-ring into the same groove, making sure it sits flat and fully in the channel all the way around. A twisted or bunched O-ring will not seal properly.
Insert the new filter cartridge into the cap, making sure it seats all the way down. The cartridge has a rubber seal on the bottom that should contact the cap's base. Screw the cap back onto the engine by hand first, turning it clockwise until you feel the new O-ring compress and the cap begins to tighten. Once hand-tight, use the 74 mm wrench to turn it an additional three-quarters of a turn—no more. Over-tightening cracks the plastic housing and causes leaks. The cap should be snug but not forced.
Why the O-ring matters more than you might think
The rubber O-ring is what actually stops oil from leaking around the filter cap. When you install a new filter, that O-ring is soft and pliable. Over time, heat and oil exposure harden it, and it loses its ability to compress and seal. If you reuse an old O-ring, it may look fine but will not seal as well as a new one. This is why Honda and every filter manufacturer recommends replacing it every time you change the filter.
A leaking filter cap is not just messy—it can cause your oil pressure to drop if enough oil escapes. Your oil pressure warning light may come on, or you might not notice until you check the dipstick and find the level dangerously low. Replacing a $3 O-ring takes 30 seconds and prevents a $500 engine problem. It's one of the easiest preventive steps you can take during an oil change.
Common mistakes to avoid
The most frequent error is over-tightening the filter cap. The plastic housing is not as strong as a metal spin-on filter, and cranking the wrench too hard will crack it. You'll then have a leak that requires replacing the entire housing, not just the cap. Hand-tight plus three-quarters of a turn is the correct torque. If you're not sure you've got it right, err on the side of loose—a slightly loose cap will drip, and you'll notice it when ready. A cracked housing may not leak right away and can cause problems later.
Another common mistake is forgetting to replace the O-ring or installing it twisted. If the O-ring is not seated flat in its groove, it will not seal, and you'll have an oil leak within a few days of driving. Take the extra 20 seconds to make sure it's sitting properly all the way around the groove before you install the cartridge.
Checking your work after installation
After you've reinstalled the cap and refilled the engine with fresh oil, start the engine and let it idle for 30 seconds. Watch the oil pressure gauge or wait for the oil pressure warning light to go out—this tells you that oil is circulating and the filter is not restricting flow. Turn the engine off and wait two minutes, then look under the filter cap area for any drips. If you see oil pooling, the cap is not tight enough or the O-ring is not seated. Loosen the cap, check that the O-ring is flat in its groove, and retighten.
Check the oil level on the dipstick after the engine has been off for at least five minutes. The level should be at or near the full mark. If it's low, you may not have added enough new oil, or there may be a leak you haven't spotted yet. Drive the car for a few miles and park it on a clean surface, then check underneath after 10 minutes. No drips means the job is done correctly.
Frequently Asked Questions
Can I use a spin-on filter on my 2016 Odyssey instead of the cartridge?
No. The 2016 Odyssey is designed for a cartridge filter only. The engine has no provision for a spin-on filter, and trying to adapt one will not work. Stick with the cartridge design Honda engineered for this engine.
What happens if I don't replace the O-ring?
The old O-ring will harden and lose its seal over time. You may see oil leaking from the filter cap within a few days or weeks. Replacing it costs $3 and takes 30 seconds, so it's not worth skipping.
How tight should the filter cap be?
Hand-tight plus three-quarters of a turn with the wrench. Do not use full force or crank it as tight as you can—the plastic housing will crack. If you're unsure, go slightly loose; a small drip is easier to fix than a cracked housing.
Can I change the filter without draining the oil?
Yes, you can change the filter without draining the oil. However, you will lose some oil when you remove the cap because the filter cavity holds about half a quart. If you're doing a full oil change, drain first, then change the filter. If you're only changing the filter between oil changes, expect to top up the level afterward.
What if the filter cap is stuck and won't turn?
Let the engine cool completely, then try again with the wrench. If it's still stuck, explore a penetrating oil like PB Blaster around the cap's base and wait 15 minutes. Do not force it—forcing can crack the plastic. If it remains stuck after cooling and penetrating oil, have a shop remove it to avoid damaging the housing.