The 2016 Honda Pilot uses a cartridge-style oil filter located on top of the engine

The 2016 Honda Pilot has a cartridge oil filter, not the spin-on type you screw off. This filter sits in a housing on the top of the engine, toward the front. You'll see a large cylindrical cap — that's the filter housing. The filter element itself is inside that cap, and you replace it by unscrewing the cap, removing the old filter, and installing a new one along with a new rubber seal.

This design is common on Honda vehicles and is simpler than it looks once you know what you're doing. The whole job takes about 10 to 15 minutes if you're changing the oil at the same time, or 5 minutes if you're just swapping the filter.

Key Takeaways

  • The 2016 Pilot's filter is a cartridge type inside a cap on top of the engine, not a spin-on filter you twist off.
  • You will need a filter wrench to unscrew the housing cap, a new filter element, and a new rubber crush washer for the cap.
  • The correct replacement filter is Honda part number 15400-PLM-A02 or equivalent aftermarket cartridge filters rated for the Pilot.
  • The filter housing cap should be torqued to 29 foot-pounds, which is snug but not as tight as you might think.
  • Changing the filter at the same time as the oil keeps your engine cleaner and is the standard practice during oil service.

What filter and parts you need

The OEM filter for the 2016 Pilot is Honda part 15400-PLM-A02. This is the genuine Honda cartridge filter. You can also use aftermarket cartridge filters from Fram, Mobil 1, Bosch, or other major brands — just make sure the part number is listed as compatible with a 2016 Honda Pilot. Do not buy a spin-on filter by mistake; they will not fit.

You will also need a new rubber crush washer (also called a seal or O-ring) that goes on the filter housing cap. Honda part number is 90430-R70-003. This washer compresses when you tighten the cap and creates the seal. Reusing the old one can cause leaks. Many filter kits include the washer, but check the box before you start.

A filter wrench is essential. The housing cap is tight and difficult to turn by hand. A cartridge filter wrench (a socket-like tool with a rubber grip) costs $8 to $15 and fits over the cap. You can also use a strap wrench if you have one, but a cartridge wrench is faster and easier.

Step-by-step filter replacement

Start with the engine cold or warm but not hot — you don't want to burn yourself on hot oil. Locate the filter housing cap on top of the engine. It's a large cylindrical cap with a bolt in the center, usually toward the front of the engine bay.

Place a drain pan underneath the housing. When you unscrew the cap, some oil will drip out — not a full quart, but enough to make a mess. Fit your filter wrench over the cap and turn it counterclockwise. It will be tight; use steady pressure and don't rush. Once it breaks loose, you can unscrew it by hand.

Lift the cap straight up and out. The old filter cartridge will come out with it, still attached to the underside of the cap. Remove the old filter by hand — it will be oily. Wipe the inside of the housing clean with a lint-free rag or paper towel. Look for any debris or old rubber pieces and remove them.

Take the new rubber crush washer and place it on the center bolt of the cap. Then insert the new filter cartridge into the cap, pushing it down until it seats. The filter should not be loose or rattle. Lower the cap and filter assembly back into the housing and thread it in by hand first to avoid cross-threading. Once hand-tight, use the filter wrench to tighten it to 29 foot-pounds. This is snug but not over-tight — over-tightening can damage the seal or the housing.

When to replace the filter

Honda recommends changing the oil and filter every 10,000 miles under normal driving conditions, or every 5,000 miles if you drive in severe conditions (towing, dusty roads, frequent short trips, or extreme temperatures). The 2016 Pilot has an oil life monitoring system on the dashboard that tells you when service is due. When the system shows 15% oil life remaining or less, it's time to change both the oil and filter.

Some owners change the filter more often than the oil — for example, every other oil change — but this is not necessary on the Pilot. The cartridge filter is designed to last the full service interval, and changing it with the oil is the standard approach.

Common mistakes to avoid

The most common error is forgetting the new crush washer. If you install the cap without a fresh washer, the seal won't be tight and you'll get an oil leak around the housing. Always replace the washer every time you change the filter.

Another mistake is over-tightening the cap. The 29 foot-pound specification exists because the aluminum housing can crack if you crank too hard. If you don't have a torque wrench, tighten until snug and then give it a quarter turn more — that's usually close enough. You can also take it to a shop if you're unsure about the torque.

Some people accidentally buy the wrong filter type. The 2016 Pilot does not use a spin-on filter, so double-check the part number before you buy. If the listing says "cartridge" or "top-mounted" and lists the Pilot as compatible, you have the right one.

Tools and supplies checklist

ItemPurposeNotes
Cartridge oil filter (Honda 15400-PLM-A02 or equivalent)Replacement filter elementCheck part number matches 2016 Pilot
Rubber crush washer (Honda 90430-R70-003)Seal for filter housing capMust be new each time
Cartridge filter wrenchRemove and install housing cap$8–$15, essential tool
Drain panCatch dripping oilHolds 1–2 quarts
Lint-free rags or paper towelsClean housing interiorPrevents debris in engine
Torque wrench (optional)Tighten cap to 29 ft-lbsHelpful but not required

Frequently Asked Questions

Can I change just the filter without changing the oil?

Yes, you can. The filter can be replaced independently, though it's not common practice. Most people change both at the same time because the filter is already off and the job is quick. If you do change only the filter, you'll still need the new crush washer and the same tools.

What happens if I over-tighten the filter cap?

Over-tightening can crack the aluminum housing or damage the rubber seal, leading to oil leaks. It can also make the cap very difficult to remove next time. Stick to 29 foot-pounds or hand-tight plus a quarter turn if you don't have a torque wrench.

Is the OEM Honda filter better than aftermarket?

The OEM filter is designed specifically for the Pilot and is reliable. Quality aftermarket filters from brands like Fram, Mobil 1, or Bosch perform similarly and often cost less. The key is buying a cartridge filter rated for the 2016 Pilot, not the cheapest option you find.

How much oil drips out when I remove the filter?

Usually less than a quart, but it varies. Have a drain pan ready and expect some spillage. If you're also changing the oil, you'll be draining the pan anyway, so this is a minor concern.

Do I need to prime the new filter with oil before installing it?

No. Unlike spin-on filters, cartridge filters do not need to be pre-filled with oil. straightforward install the dry filter and the engine will circulate oil through it on startup.