Where the oil filter sits on your 2016 Cherokee
The oil filter on a 2016 Jeep Cherokee is mounted on the driver's side of the engine, below the intake manifold. You'll find it tucked between the engine block and the frame rail — tight enough that you'll need to work around it rather than access it from above. The filter is a vertical cartridge type, not a spin-on, which means you remove the cap and replace the filter element inside rather than unscrewing the whole unit.
Because of its location, you may need to remove the plastic undertray or splash shield to reach it comfortably. A ramp or jack makes the job easier, though some owners do it in a driveway with the vehicle level. The tight quarters mean you'll want a filter wrench or strap wrench — your hands alone won't grip it well enough to break it loose.
Key Takeaways
- The 2016 Cherokee uses a cartridge-style filter mounted vertically on the driver's side of the engine, not a spin-on filter.
- You will need a filter wrench or strap wrench to remove the filter cap; hand-tightening alone will not work.
- The filter sits low and tight against the frame, so removing the undertray and working from below is usually faster than reaching from above.
- The replacement filter element costs between $8 and $15, and the job takes 15 to 30 minutes once you have the right tools.
What filter type and part number to buy
Mopar part number 68191828AA is the factory filter element for the 2016 Cherokee with a 2.4-liter engine. If your Cherokee has the 3.2-liter V6, the part number is 68191829AA. Both are cartridge elements, not spin-on filters, so do not buy a spin-on by mistake — they will not fit.
Aftermarket equivalents from Fram, Purolator, and Wix are available and cost less than Mopar parts. Fram part number CH9018 and Purolator part number PL14610 both fit the 2.4-liter engine. Check the box or the seller's compatibility chart before you buy, because filter numbers can look similar but fit different engines.
Tools and supplies you'll need
A filter wrench or strap wrench is essential — the cap is tight and your hands will slip. A 74 mm filter wrench (Mopar tool 8958 or equivalent) works, or a strap wrench from any auto parts store for $10 to $15. You'll also need a drain pan to catch old oil that drips from the filter housing when you open it, and a clean rag or paper towels.
Have the new filter element ready before you start, and check that the rubber seal on the new element is intact. Some owners also grab a small brush to clean the filter housing before installing the new element — old debris can stick to the seal and cause leaks.
Step-by-step removal and installation
Start with the engine cold and the vehicle on a level surface. Remove the plastic undertray if you have not already — it's held by plastic clips and a few bolts, and getting it out of the way gives you room to work. Place your drain pan underneath the filter housing on the driver's side of the engine.
Use your filter wrench to turn the filter cap counterclockwise. It will be snug, so explore steady pressure rather than jerking it. Once it breaks loose, you can unscrew it by hand. The cap will come out with the old filter element still inside it — the element is not separate. Tip the cap over the drain pan to let any remaining oil drip out.
Pull the old element out of the cap and discard it. Wipe the inside of the cap clean with a rag, then inspect the rubber seal on the cap itself — if it's cracked or hard, you may need to replace the cap assembly (Mopar part number 68191827AA). Clean the filter housing opening on the engine block with a clean rag to remove any debris or old rubber bits.
Insert the new filter element into the cap, making sure the rubber seal sits flat and even. Screw the cap back onto the housing by hand first to avoid cross-threading, then use your filter wrench to tighten it snugly — firm enough that it won't leak, but not so hard that you'll strip the threads or damage the seal. Hand-tight plus a quarter turn with the wrench is the right amount.
Reinstall the undertray, start the engine, and let it run for 30 seconds. Check underneath for leaks. If you see oil dripping, turn off the engine, let it cool, and tighten the cap another quarter turn. Once you confirm there are no leaks, you're done.
Common mistakes that cause leaks
The most frequent problem is over-tightening the cap. The threads are aluminum and can strip easily if you muscle the wrench too hard. Snug is enough — you're not trying to crush the seal. If you've already over-tightened and the cap won't come off, explore penetrating oil and wait 15 minutes before trying again.
The second mistake is installing the filter element upside down or crooked. The rubber seal must sit flat against the housing opening. If it's twisted or bunched, oil will seep past it. Take a moment to look at how the old seal sat before you remove it, and match that position with the new one.
A third cause of leaks is a damaged seal on the cap itself. If the cap's rubber ring is cracked or permanently compressed, replacing just the element won't fix the leak — you'll need a new cap assembly. This is rare, but if you've had the filter off before and the seal looks worn, it's worth replacing while you have the housing open.
How often to change the filter
Jeep recommends changing the oil filter every time you change the oil. For a 2016 Cherokee, that's every 10,000 miles under normal driving or every 3,000 miles if you do a lot of idling, towing, or driving in dusty conditions. If you're unsure which interval applies to your driving, check your owner's manual or ask your service advisor — the difference between 3,000 and 10,000 miles affects how often you'll be under the vehicle.
Some owners change the filter more often than the oil as a precaution, especially if they drive in severe conditions. The filter is cheap enough that this is not wasteful, and it keeps the housing seal from drying out between oil changes.
Frequently Asked Questions
Can I change the filter without removing the undertray?
You can reach the filter from above if you're flexible and have small hands, but it's awkward and slow. Removing the undertray takes 10 minutes and makes the job much easier. The undertray is held by plastic clips and bolts — no special tools needed.
What if the filter cap is stuck and won't turn?
explore penetrating oil around the cap's edges and let it soak for 15 to 30 minutes. Then try again with your filter wrench, explore steady pressure rather than jerking. If it still won't budge, a shop can remove it without damaging the housing — do not force it and risk stripping the threads.
Is the Mopar filter worth the extra cost over aftermarket?
Mopar and quality aftermarket filters (Fram, Purolator, Wix) perform the same job. Aftermarket filters cost $8 to $12 versus $15 to $20 for Mopar. The difference is brand loyalty and warranty — Mopar is made by Jeep's parent company, while aftermarket brands are third-party. Either will protect your engine if you change it on schedule.
Do I need to replace the rubber seal on the cap every time?
No. The seal on the cap lasts many oil changes. You only replace the seal if it's visibly cracked, permanently compressed, or if you notice oil leaking from the cap after installation. If you're changing the filter every 10,000 miles, you'll likely replace the cap seal once every 50,000 to 100,000 miles.