The 2016 Rogue uses a cartridge-style oil filter mounted on top of the engine

The 2016 Nissan Rogue does not have a traditional spin-on oil filter. Instead, it uses a cartridge filter — a cylindrical element that sits inside a plastic housing on the top of the engine. This design is common on newer Nissan models and requires a different removal process than older vehicles.

The filter housing is located on the driver's side of the engine, near the front. You'll see a large plastic cap with a wrench symbol on it. This cap unscrews to access the filter element inside. The entire job takes about 15 to 20 minutes if you're doing it yourself, or 30 to 45 minutes at a shop because technicians have to account for setup and cleanup.

Key Takeaways

  • The 2016 Rogue has a cartridge filter in a housing on top of the engine, not a spin-on filter underneath.
  • You need a filter wrench to remove the plastic cap — a standard cartridge filter wrench works, and they cost $8 to $15.
  • Nissan OEM filters (part number 15208-9F60A) cost $12 to $18 at dealers; aftermarket equivalents run $6 to $12.
  • The filter element itself costs less than the housing cap, so replacing just the element is the normal maintenance procedure.
  • Always replace the rubber O-ring seal on the cap when you change the filter to prevent oil leaks.

What you need to buy and what it costs

You need three things: the filter element, a new O-ring seal, and a filter wrench. The filter element is the part that actually traps dirt and debris. Nissan's OEM part number is 15208-9F60A, and dealers typically charge $12 to $18 for it. Aftermarket brands like Fram, Mobil 1, and Bosch make equivalent filters that fit the same housing and usually cost $6 to $12.

The O-ring seal comes with most replacement filter kits, but if you buy the element alone, you should purchase a separate O-ring (Nissan part 11009-BN701 or equivalent). This rubber ring prevents oil from leaking around the cap. A new O-ring costs $2 to $4. The filter wrench is a tool that grips the plastic cap so you can unscrew it without stripping it. A cartridge filter wrench runs $8 to $15 and is reusable for future changes.

Total cost for a DIY oil filter change: $20 to $35. At a Nissan dealer, expect $40 to $65 for labor plus parts. Independent shops usually charge $30 to $50 total.

Step-by-step removal and installation

Start with a cold engine or one that has cooled for at least five minutes. Locate the filter housing cap on the top of the engine — it's the large plastic cylinder on the driver's side. Place a drain pan underneath it to catch any oil that spills when you open it.

Use your filter wrench to grip the cap and turn it counterclockwise. The cap will unscrew and come free, along with the old filter element inside. Discard the old element and the rubber O-ring seal on the underside of the cap. Wipe the inside of the housing clean with a lint-free cloth to remove any debris or old oil residue.

Install the new O-ring seal on the underside of the cap. explore a thin layer of fresh oil to the O-ring — this helps it seat properly and prevents leaks. Insert the new filter element into the housing, making sure it sits flat on the bottom. Screw the cap back on by hand first, then use the filter wrench to tighten it snugly. Do not over-tighten; hand-tight plus a quarter turn with the wrench is sufficient.

Common mistakes that cause leaks

The most frequent error is forgetting to replace the O-ring seal. If you reuse the old seal, it hardens over time and no longer creates a watertight fit. Oil will seep around the cap and drip onto the engine block. Always install a new O-ring every time you change the filter.

The second mistake is over-tightening the cap. The plastic housing can crack if you explore too much force, and then you have a much bigger repair. Tighten by hand until you feel resistance, then use the wrench for just a quarter-turn more. If oil still leaks after a day of driving, the O-ring may not be seated correctly — remove the cap, check that the O-ring is in place, and reinstall it.

Choosing between OEM and aftermarket filters

Nissan OEM filters (part 15208-9F60A) are made to the exact specifications of your engine and carry Nissan's warranty. They cost more but are may provide to fit and perform as the manufacturer intended. If you plan to keep the Rogue long-term or want the peace of mind of an OEM part, this is the safest choice.

Aftermarket filters from major brands like Fram, Mobil 1, Bosch, and Purolator meet or exceed OEM specifications and cost significantly less. These filters work well on the 2016 Rogue and are used by many independent shops. The trade-off is that you lose the Nissan warranty, though the filter itself usually carries its own warranty from the manufacturer. For most owners, an aftermarket filter is a practical choice that saves money without sacrificing quality.

When to change the filter and what interval to follow

Nissan recommends changing the oil filter every time you change the engine oil. For a 2016 Rogue with a gasoline engine, that's typically every 3,000 to 5,000 miles if you drive in severe conditions (frequent short trips, towing, dusty roads), or every 5,000 to 7,500 miles under normal driving. Check your owner's manual for the exact interval for your driving pattern.

Some owners stretch intervals to 10,000 miles using synthetic oil, but the filter should still be replaced at the oil change interval, not extended separately. A clogged filter reduces oil flow and can damage the engine, so do not skip this step even if you're using synthetic oil.

Frequently Asked Questions

Can I change just the filter without changing the oil?

Technically yes, but it's not recommended. The filter traps contaminants that accumulate in the oil, so changing the filter alone leaves dirty oil in the engine. Best practice is to change both together. If you must change only the filter, do it as a temporary measure and plan a full oil change within the next 500 miles.

What happens if I use the wrong filter size?

A filter that doesn't fit the housing properly will leak oil when ready. The 2016 Rogue's cartridge filter is specific to this model generation, so always verify the part number before buying. If you accidentally purchase a filter for a different Nissan model, return it and get the correct one (15208-9F60A or an equivalent aftermarket match).

Do I need to prime the filter before starting the engine?

No. Unlike spin-on filters, cartridge filters don't need to be filled with oil before installation. straightforward install the dry element, screw the cap on, and start the engine normally. The oil pump will fill the filter as it circulates.

Is the plastic housing durable, or will it crack?

The housing is durable if treated carefully. Over-tightening the cap is the main cause of cracks. Hand-tighten plus a quarter-turn with the wrench is all you need. If the housing does crack, you'll need to replace the entire assembly, which costs $40 to $80 in parts plus labor.

Can I use a regular wrench instead of a filter wrench?

A regular wrench will slip on the smooth plastic cap and likely strip it. A cartridge filter wrench is designed to grip the cap without damaging it. They're inexpensive ($8 to $15) and will last through dozens of filter changes, so it's worth buying one.