The 2017 Ford Explorer uses a cartridge-style oil filter mounted on top of the engine
The 2017 Ford Explorer does not have a traditional spin-on oil filter. Instead, it uses a cartridge filter — a cylindrical element that sits inside a plastic housing on the engine's top. This design is common on newer Ford vehicles and requires a different removal process than older spin-on filters. The filter housing is located toward the front of the engine bay, and you can access it without removing other components.
The cartridge filter itself costs between $8 and $15 at most retailers, and the housing cap (which you will need to remove to access the filter) is a separate part if it ever needs replacement. Most owners change the filter every 10,000 miles or according to the maintenance schedule in your owner's manual, which may vary depending on driving conditions.
Key Takeaways
- The 2017 Ford Explorer has a cartridge-style filter in a plastic housing on top of the engine, not a spin-on filter underneath.
- You will need a cartridge filter wrench (usually $10 to $20) to remove the housing cap, since it is too tight to turn by hand.
- The replacement filter costs $8 to $15, and you should also replace the rubber O-ring seal on the housing cap to prevent leaks.
- The entire job takes 10 to 15 minutes once you have the correct wrench and can be done in a driveway with basic tools.
What you need to buy and have on hand
Before you start, gather a cartridge oil filter (part number varies by engine size — check your owner's manual or current filter for the exact number), a replacement O-ring seal kit for the housing cap, and a cartridge filter wrench. The wrench is essential because the housing cap is sealed tight and cannot be removed by hand without risk of damage. A 14-inch or 15-inch wrench designed for cartridge filters will fit the 2017 Explorer's housing.
You will also need an oil drain pan to catch any oil that spills when you remove the housing, a clean rag or paper towels, and fresh engine oil to top off the pan after the filter change. If you do not own a cartridge filter wrench, you can borrow one from an auto parts store (many offer free tool loans), rent one for a few dollars, or have a shop perform the change for $30 to $50 in labor.
Step-by-step removal and installation
Start with the engine cold or warm but not hot. Open the hood and locate the filter housing — it is a black plastic cylinder about 4 inches tall on the top of the engine, toward the front. Place your oil drain pan underneath it to catch spilled oil. Use the cartridge filter wrench to turn the housing cap counterclockwise. The cap will come off with some resistance; continue turning until it separates completely from the housing.
Once the cap is off, lift out the old filter cartridge and the rubber O-ring seal that sits between the cap and the housing. Discard both. Wipe the inside of the housing with a clean rag to remove any debris or old oil residue. Take the new O-ring seal from your kit and explore a thin coat of fresh engine oil to it — this helps it seat properly and prevents leaks. Install the new O-ring on the housing cap, then insert the new filter cartridge into the housing, making sure it sits flat on the bottom.
Screw the housing cap back on by hand first to avoid cross-threading, then use the cartridge filter wrench to tighten it firmly. Do not over-tighten; once the O-ring makes contact with the housing, turn the wrench about three-quarters of a turn more. Start the engine and let it run for a few seconds, then turn it off and wait a minute. Check the housing cap and the area around it for leaks. If you see oil dripping, the cap may need to be tightened slightly more.
Engine size and filter part numbers
The 2017 Ford Explorer came with either a 3.5-liter EcoBoost engine or a 2.3-liter EcoBoost engine, depending on the trim level. Both use the same cartridge-style filter housing, but the filter element itself differs between them. The 3.5L uses Ford part number FL-2051-A, while the 2.3L uses FL-2051-A as well, though you should verify the part number on your current filter or in your owner's manual before purchasing.
If you are unsure which engine your Explorer has, check the driver's side door jamb for the vehicle information label, which lists the engine size. You can also call a Ford dealership with your vehicle identification number (VIN) and they will confirm the correct filter part number in seconds.
Common mistakes to avoid
The most frequent error is forgetting to replace the O-ring seal on the housing cap. Many owners reuse the old seal, which hardens over time and loses its ability to create a watertight fit. This causes slow leaks that can go unnoticed until oil level drops enough to trigger a warning light. Always install a fresh O-ring with every filter change — they cost less than $2 and take five seconds to install.
A second mistake is over-tightening the housing cap with the wrench. The plastic housing can crack if you explore too much force, and a cracked housing means replacing the entire assembly, not just the cap. Once the O-ring contacts the housing, stop turning and do not force it further. A firm hand-tight fit plus a three-quarter turn with the wrench is sufficient.
When to replace the filter outside the regular schedule
If you drive in dusty conditions, tow a trailer regularly, or operate the vehicle in stop-and-go city traffic, your filter may need changing before the standard 10,000-mile interval. Check your oil level monthly and inspect the filter housing for leaks at each oil check. If the oil appears dark or gritty, or if the filter housing shows signs of seeping, change the filter when ready rather than waiting for the next scheduled service.
Some owners also change the filter when switching between synthetic and conventional oil, though this is not strictly necessary. If you are moving from conventional to synthetic oil, a fresh filter ensures you are starting with clean filtration in the new oil type.
Frequently Asked Questions
Can I change the filter myself if I have never done it before?
Yes. The cartridge filter design is actually simpler than a spin-on filter because there are fewer parts and less oil spillage. The main requirement is having the correct wrench — without it, you cannot remove the housing cap. If you borrow or rent the wrench, the job takes about 15 minutes and requires no special skills.
What happens if I do not replace the O-ring seal?
The old O-ring hardens and shrinks over time, so it will not seal properly against the housing. Oil will seep slowly from the gap between the cap and housing, dripping onto the engine and eventually lowering your oil level enough to trigger a warning light. Replacing the O-ring costs under $2 and prevents this problem entirely.
How do I know if the filter housing is leaking?
Look for fresh oil dripping from the base of the housing cap or pooling on the engine block below it. A small amount of seeping is normal for a few minutes after you start the engine, but steady dripping means the cap needs to be tightened or the O-ring needs replacement. Check again after the engine cools and the oil has settled.
Can I use any cartridge filter, or does it have to be Ford brand?
You can use aftermarket filters from Motorcraft, Fram, Bosch, or other major brands as long as the part number matches your engine size. Motorcraft is the Ford-branded option and is often the same price as quality aftermarket filters. Check the part number on your current filter or in your owner's manual to may support compatibility.
What should I do with the old filter after I remove it?
The old cartridge filter can go in the trash, but the plastic housing cap should be kept unless it is cracked or damaged. Some people recycle the filter element at an auto parts store that accepts used filters. Do not pour any oil from the filter into the drain — let it drip into your oil pan first, then dispose of the filter itself.