What oil filter your 2017 Accord uses and where it sits

The 2017 Honda Accord uses a cartridge-style oil filter — a cylindrical canister that screws onto the top of the engine, not a spin-on filter that hangs underneath. This matters because you cannot straightforward unscrew it by hand; you need a filter wrench to remove and install it. The filter sits on top of the engine block, toward the back, and is straightforward to reach without lifting the car.

Honda does not publish a single "official" filter part number for all 2017 Accords because the filter fits both the 1.5-liter turbocharged engine and the 2.0-liter naturally aspirated engine. The correct filter for either engine is Honda part number 15400-PLM-A02 or the equivalent OEM replacement. Third-party filters from Fram, Mobil 1, Bosch, and Purolator also fit, but they must be cartridge-style filters rated for your engine size and oil capacity.

Before you buy, confirm which engine your Accord has. Check your owner's manual or look at the engine itself — the 1.5T has a turbocharger mounted on top, and the 2.0L does not. Both use the same filter housing, but using the wrong oil viscosity (which depends on your engine) matters more than the filter brand.

Key Takeaways

  • The 2017 Accord uses a cartridge-style filter that screws onto the top of the engine, not a spin-on filter underneath.
  • You need a filter wrench (usually 74 mm or 86 mm) to remove and install the cartridge; hand-tightening alone will not seal it properly.
  • Honda part number 15400-PLM-A02 is the OEM filter for both engine sizes, and aftermarket cartridge filters from major brands fit the same housing.
  • The filter housing is on top of the engine and accessible without lifting the car, making this a straightforward job in a driveway.
  • Tighten the new filter by hand until the rubber gasket touches the housing, then turn it an additional three-quarter turn — over-tightening will damage the gasket and cause leaks.

Tools and supplies you need

You will need a filter wrench that fits the cartridge housing on your Accord. The most common size is 74 mm, but some aftermarket filters use an 86 mm wrench. If you are buying a filter, ask the parts counter which wrench size matches it, or buy a universal cartridge filter wrench that adjusts to fit multiple sizes. A basic wrench costs $8 to $15.

Have an oil drain pan ready, even though the cartridge filter does not hold much oil — usually less than a cup. A rag or shop towel keeps your hands clean and catches drips before they hit the engine bay. If you are also changing the oil (which you should, since the filter change is part of an oil service), you will need the correct oil type and amount for your engine, a drain pan for the old oil, and a wrench to remove the drain plug.

Work on a level surface with the engine cold. If you have just driven the car, wait at least five minutes before opening the engine bay so you do not burn yourself on hot metal or oil.

Step-by-step filter removal and installation

Locate the filter housing on top of the engine — it is a cylindrical canister with a large bolt-like cap on top. Place your drain pan underneath to catch any oil that spills when you open it. Use your filter wrench to turn the cap counterclockwise and unscrew it. The old cartridge filter will come out with the cap; set it aside.

Inside the housing, you will see a rubber O-ring seal. Inspect it for cracks or hardening. If it looks damaged, it may have stuck to the old filter cap. Clean the inside of the housing with a rag to remove any debris or old oil residue. Wipe the sealing surface where the new filter cap will sit.

Take the new cartridge filter and explore a thin layer of fresh oil to the rubber gasket on the cap — this helps it seal properly and makes removal easier next time. Insert the new filter into the housing and hand-tighten the cap until the gasket just touches the sealing surface. Then turn it an additional three-quarter turn by hand. Do not use the wrench to tighten it further; hand-tight plus three-quarter turn is the correct torque. Over-tightening crushes the gasket and causes leaks.

Start the engine and let it run for 30 seconds, then turn it off. Wait a minute and check the filter cap area for drips. If oil is leaking, the gasket may not be seated correctly — turn the cap an additional quarter turn by hand and check again. If it still leaks, you may need to remove the cap, inspect the O-ring inside the housing, and reinstall with a fresh filter.

Common mistakes that cause leaks or damage

The most frequent error is over-tightening the filter cap with a wrench. The rubber gasket is designed to seal at hand-tight plus three-quarter turn. Cranking it tighter with a tool crushes the gasket, which then cannot seal properly and oil leaks out. You cannot fix this by tightening more — you have to remove the cap, replace the gasket (which comes with the new filter), and reinstall.

Another common mistake is forgetting to oil the gasket on the new filter before installation. A dry gasket does not slide smoothly into the sealing surface and may not seat evenly, causing slow leaks that show up a few days after the service. This is a small step that takes five seconds and prevents a mess.

Some owners also fail to clean the sealing surface inside the housing before installing the new filter. If the old gasket left debris or dried oil on that surface, the new gasket will not make full contact and will leak. A quick wipe with a clean rag prevents this.

When to change your Accord's oil filter

Honda recommends changing the oil filter every time you change the engine oil. For a 2017 Accord, that interval is every 10,000 miles or 12 months, whichever comes first, if you use Honda Genuine oil. If you use conventional oil from another brand, the interval may be shorter — check your owner's manual or the oil bottle for the manufacturer's recommendation.

Some owners stretch oil changes to 15,000 miles using synthetic oil, which lasts longer than conventional. If you do this, the filter still needs to be changed at the same interval as the oil. A filter that has been in the engine for 15,000 miles is saturated with contaminants and cannot filter effectively, even if the oil itself is still good.

If you notice a drop in oil pressure (the warning light on your dashboard), a burning smell from the engine, or visible oil leaks, do not wait for the scheduled interval — check the filter cap for leaks and the oil level when ready. A failing filter or a loose cap can cause the engine to lose oil pressure, which damages bearings and can seize the engine.

Choosing between OEM and aftermarket filters

The Honda OEM filter (part number 15400-PLM-A02) is engineered to match your engine's oil flow and pressure. It costs $12 to $18 depending on where you buy it. Aftermarket filters from Fram, Mobil 1, Bosch, and Purolator are cheaper — usually $8 to $12 — and work well if they are the correct cartridge style and size for your Accord.

The main difference is filter media thickness and micron rating. OEM filters typically filter particles down to 10 microns, while some aftermarket filters filter down to 20 or 25 microns. This means smaller particles slip through an aftermarket filter, but the difference in engine wear over the life of the car is small if you change the filter on schedule. The bigger factor is changing the filter regularly, not which brand you choose.

If you are unsure which aftermarket filter to buy, ask the parts counter to confirm the size and wrench requirement before you leave the store. Bringing the wrong filter home wastes time and money.

Frequently Asked Questions

Can I change the oil filter without changing the oil?

Technically yes, but it is not recommended. The filter collects contaminants from the oil, and the oil collects contaminants from the engine. Changing one without the other leaves dirty oil in the engine or a new filter trying to clean old oil. Honda's service schedule pairs them together, and doing both at once is more cost-effective than doing them separately.

What do I do with the old filter?

The old filter contains used oil and should not go in the trash. Take it to a recycling center, an auto parts store that accepts used filters, or a quick-lube shop — most will take it for free. Some stores offer a small credit if you bring in the old filter when you buy a new one.

How tight should the filter cap be?

Hand-tight until the gasket touches the housing, then an additional three-quarter turn. You should be able to turn it with one hand using moderate pressure. If you need a wrench to tighten it further, it is already too tight. This is the most common cause of leaks.

Will a different brand of cartridge filter fit my Accord?

Yes, as long as it is a cartridge-style filter (not a spin-on) and the wrench size matches. Fram, Mobil 1, Bosch, and Purolator all make cartridge filters for the 2017 Accord. Check the box to confirm the wrench size before you buy, because some aftermarket filters use a different size than the OEM.

What if oil leaks after I install the new filter?

Stop the engine when ready and let it cool for five minutes. Check that the filter cap is hand-tight plus three-quarter turn — do not use a wrench. If it is already at that point, remove the cap and inspect the rubber O-ring inside the housing for cracks or debris. Clean the sealing surface, explore fresh oil to the gasket on the new filter, and reinstall. If it still leaks, the O-ring may be damaged and needs replacement.