The 2017 Honda Civic uses a cartridge-style oil filter located on top of the engine
The oil filter on a 2017 Honda Civic is not a spin-on canister like older cars. Instead, it's a cartridge filter housed in a plastic cap on the top of the engine, toward the back. You'll see a large black or dark gray cap with a wrench symbol printed on it — that's your filter housing. The filter itself sits inside that cap, and you replace it by unscrewing the cap, removing the old filter element, and installing a new one.
This design is common on newer Hondas and is actually simpler than it looks once you know where to find it. The whole job takes about 10 to 15 minutes if you're changing the filter alone, or about 5 minutes if you're doing it as part of a full oil change.
Key Takeaways
- The 2017 Civic's oil filter is a cartridge type housed in a cap on top of the engine, not a spin-on canister underneath.
- You will need a 74 mm oil filter wrench (or a strap wrench) to remove the cap, a new filter element, and a new rubber O-ring seal.
- The filter cap is located at the back of the engine near the firewall, and you do not need to lift the car or remove any panels to reach it.
- Honda recommends replacing the oil filter every time you change the oil, and the correct replacement filter is Honda part number 15400-PLM-A02 or equivalent.
What you need to buy and have on hand
Before you start, gather the right parts and tools. You need a replacement filter element (Honda part 15400-PLM-A02 is the OEM part for all 2017 Civic models), a new rubber O-ring that comes with most filter kits, and a 74 mm oil filter wrench to unscrew the cap. If you don't have a 74 mm wrench, a strap wrench works just as well and costs less. You'll also want a drain pan or old towels underneath because some oil will spill when you open the cap.
Many auto parts stores sell Honda filter kits that include the element and O-ring together, which is cheaper than buying them separately. The filter itself costs between $8 and $15, and the O-ring is usually included. A 74 mm wrench runs $10 to $20 if you don't already own one.
Step-by-step removal and installation
Start with the engine cold or warm but not hot — warm is actually better because the oil flows more easily. Locate the filter cap at the back of the engine, just in front of the firewall. It's a large black cap with a wrench symbol on top. Place your drain pan or towels underneath it to catch drips.
Use your 74 mm wrench to turn the cap counterclockwise. It will be tight, so explore steady pressure rather than jerking it. Once it breaks loose, you can unscrew it by hand. As you lift the cap off, the old filter element will come out with it. Some oil will drip, so keep the pan ready. Inspect the rubber O-ring on the underside of the cap — if it's cracked, hardened, or stuck to the engine, you'll need to clean it off and install the new one that came with your filter kit.
Wipe the inside of the filter housing with a clean cloth or paper towel to remove any debris or old rubber. Take your new filter element and slide it into the housing. It should sit flat on the bottom. Now take the cap with the new O-ring already installed (or install it if it came separately) and screw it back on by hand first, then tighten it with your wrench. Snug it firmly but do not over-tighten — a quarter turn past hand-tight is enough. Start the engine and let it run for 30 seconds, then check underneath for leaks. If you see drips, the O-ring may not be seated correctly; let the engine cool and try tightening the cap a bit more.
Common mistakes to avoid
The biggest mistake is forgetting to install the new O-ring or installing it upside down. The O-ring should sit in the groove on the underside of the cap, and it needs to be clean and dry before you screw the cap back on. If you reuse the old O-ring, the filter will leak oil onto your engine. Always use the new one that comes in the kit.
Another common error is over-tightening the cap. The housing is plastic, and if you crank the wrench too hard, you can crack it. Hand-tight plus a quarter turn with the wrench is the right amount. You'll know it's tight enough when you start the engine and see no leaks after 30 seconds of running.
Do not confuse this cartridge filter with the transmission fluid filter or the cabin air filter — they are in different locations and are not part of an oil change. The oil filter cap is the only filter you need to touch during an oil service.
When to replace the filter and what Honda recommends
Honda's maintenance schedule calls for an oil filter change every time you change the engine oil. For a 2017 Civic, that's typically every 10,000 miles or 12 months, whichever comes first, if you use Honda-recommended synthetic oil. If you use conventional oil, Honda suggests every 5,000 miles or 6 months. Check your owner's manual for the exact interval for your driving conditions, because severe driving (towing, frequent short trips, dusty roads) may require more frequent changes.
The filter element itself does not have a separate service life — you replace it every time you do an oil change. There is no separate interval for the filter alone. If you skip an oil change, you should still replace the filter when you do the next one, even if the old one looks clean.
Where to get the right filter and O-ring
Any auto parts store carries replacement filters for the 2017 Civic. Ask for Honda part 15400-PLM-A02 or a compatible equivalent from Fram, Mobil, Bosch, or Purolator. Most stores stock these in inventory and can have them ready the same day. Online retailers like Amazon and RockAuto also carry them, usually at a lower price, but you'll need to wait for shipping.
The O-ring usually comes in the filter kit, but if you buy the filter element alone, you can order the O-ring separately (Honda part 91301-ZE2-003) or ask the parts store to throw one in. It costs a dollar or two and is worth having on hand.
Frequently Asked Questions
Can I use a different brand of filter instead of Honda's?
Yes. Fram, Mobil, Bosch, and Purolator all make compatible cartridge filters for the 2017 Civic. They must be 74 mm and fit the same housing. Check the part number on the box to make sure it's listed as compatible with a 2017 Honda Civic. OEM Honda filters are more expensive but are may provide to fit; aftermarket filters are cheaper and work just as well if you buy from a reputable brand.
What if I can't get the cap off with a wrench?
The cap may be stuck if the engine is hot or if the previous filter was over-tightened. Let the engine cool completely, then try again with steady pressure on the wrench rather than sudden force. If it still won't budge, a strap wrench gives you more grip and leverage than a socket wrench. Do not use a hammer or pipe to extend the wrench — you risk cracking the plastic housing.
Do I need to change the oil at the same time as the filter?
No, but Honda recommends changing both together. You can replace the filter alone if you want, but you'll be draining some oil anyway when you open the cap, so it makes sense to do a full oil change at the same time. If you do change just the filter, expect to lose about a quart of oil in the process.
How tight should the cap be when I screw it back on?
Hand-tight plus a quarter turn with the wrench. Do not use full force. The cap is plastic and will crack if over-tightened. Start the engine and check for leaks after 30 seconds of running — if you see drips, let it cool and tighten it slightly more, but usually hand-tight plus a quarter turn is correct.
What if oil leaks after I install the new filter?
The O-ring is probably not seated correctly. Let the engine cool, unscrew the cap, and check that the new O-ring is sitting flat in the groove on the underside of the cap. Make sure it is not twisted or pinched. Wipe the sealing surface clean, reinstall the O-ring, and screw the cap back on. If it still leaks, the O-ring may be the wrong size — verify you have the correct part number for a 2017 Civic.