Where the oil filter sits on your 2017 Wrangler
On a 2017 Jeep Wrangler, the oil filter is mounted vertically on the driver's side of the engine block, just below the cylinder head. You'll find it tucked between the engine and the frame rail—close enough that you'll need to work around it, but accessible without removing other major components. The filter housing is a cylindrical canister about 3 inches tall, and it connects directly to the engine's oil passage.
The exact position depends on whether you have a 3.6L petrol engine (standard on most 2017 models) or the less common 2.0L turbocharged engine. Both sit in roughly the same location, but the turbo version's filter is slightly more cramped. If you're working in a driveway rather than a lift, you'll want to approach from underneath or from the side—straight-on access is tight.
Key Takeaways
- The 2017 Wrangler's oil filter is mounted on the driver's side of the engine block, below the cylinder head, and requires a standard spin-on filter wrench to remove.
- Mopar part number 68157646AA is the OEM filter for the 3.6L engine; verify your engine size before ordering because the turbo model uses a different housing.
- The filter sits close to the frame rail, so you may need to remove the driver's side wheel well liner or work from underneath to reach it comfortably.
- Always replace the rubber O-ring seal on the filter housing cap before installing a new filter, because reusing the old seal causes leaks.
- Expect the job to take 20 to 30 minutes once you have the right tools and know where to reach.
What filter your Wrangler needs
The OEM Mopar filter for the 3.6L petrol engine is part number 68157646AA. This is a spin-on canister filter that screws onto the housing mounted on the engine block. If you choose an aftermarket equivalent, look for filters rated for the 3.6L Pentastar engine and check that the thread size and O-ring diameter match—most quality brands like Fram, Motorcraft, or ACDelco make compatible versions, but buying the wrong size wastes time and creates a leak risk.
If your Wrangler has the 2.0L turbocharged engine (less common in 2017 but present in some models), the filter housing is different and requires a different part number. Check your owner's manual or the filter housing cap itself—it will have the part number stamped on it. Never guess on filter size; a filter that doesn't seat properly will either leak oil or fail to seal when you tighten it.
How to access and remove the old filter
Start with the engine cold or warm but not hot—you want to avoid burns but also want the oil to flow freely. Raise the Wrangler on a jack or drive it onto ramps so you have room to work underneath. The filter housing is on the driver's side, so you may need to remove the plastic wheel well liner to reach it comfortably. Unbolt the two or three plastic clips holding the liner and pull it away from the frame.
Once you can see the filter housing, locate the large cap at the top of the canister. This cap has a hexagonal socket on top—use a filter wrench (a socket-style wrench designed for oil filters) to turn it counterclockwise. The wrench grips the cap's outer diameter, so you need the right size for your housing. As you loosen it, oil will begin to drip, so position a drain pan underneath. Once the cap is loose enough to turn by hand, unscrew it the rest of the way and lift it off. The old filter element will come out with it, still attached to the cap.
Inspect the rubber O-ring seal on the cap—it's a small ring of rubber that sits in a groove on the underside of the cap. This seal is what keeps oil from leaking around the cap when you reinstall it. If it's cracked, hardened, or flattened, it must be replaced. Most new filters come with a replacement O-ring, but if yours doesn't, buy one separately. The old seal will not reseal properly and will cause a slow leak within days of driving.
Installing the new filter element and O-ring
Before you install anything, clean the inside of the filter housing cap with a clean rag. Any debris or old rubber bits left inside will interfere with the seal. Then remove the old O-ring from the cap's groove—it may be stuck, so use a plastic scraper or old credit card to pry it out gently. Do not use a sharp metal tool, because you can scratch the groove and ruin the seal surface.
Install the new O-ring by pressing it firmly into the groove all the way around the cap. It should sit flush and not twist or bunch. Then insert the new filter element into the cap—it will slide in and seat against the bottom of the cap. The element is a pleated paper cartridge, so handle it gently and don't squeeze it. Once the element is seated, you're ready to reinstall the cap on the housing.
Screw the cap back onto the housing by hand first—do not use the wrench yet. Hand-tighten it until the O-ring makes contact with the housing surface and the cap begins to resist. At that point, use the filter wrench to tighten it an additional three-quarter turn. Do not over-tighten; the O-ring will seal with moderate pressure, and over-tightening can damage the housing threads or crush the seal. Once it's tight, wipe away any spilled oil and reinstall the wheel well liner.
Checking for leaks and refilling oil
Start the engine and let it idle for 30 seconds. Watch the filter cap area for any drips or seeping. If oil is leaking from where the cap meets the housing, stop the engine when ready and tighten the cap another quarter turn. Wait a minute and check again. If it still leaks, the O-ring may not be seated properly—you'll need to remove the cap, inspect the O-ring and housing surface, and reinstall it.
Once the filter is sealed and not leaking, check your oil level with the dipstick. The filter change itself doesn't remove much oil, but if you drained the pan at the same time, you'll need to refill. The 2017 Wrangler with a 3.6L engine holds about 6 quarts of oil with a filter change. Use the oil grade specified in your owner's manual—typically 5W-30 for most climates. Add oil slowly and recheck the level after each quart to avoid overfilling.
Why the O-ring matters more than you think
The rubber O-ring is the only seal between the filter housing and the cap. If it's old, cracked, or not seated properly, oil will seep past it and drip onto the engine block and exhaust manifold. This creates a fire hazard if the oil reaches hot surfaces, and it also means you're losing oil without knowing it. A slow leak can drop your oil level by a quart over a few hundred miles, which puts your engine at risk of bearing damage or sludge buildup.
Many people reuse the old O-ring to save a few cents, and then spend weeks chasing a leak they can't find. Always replace it. New O-rings cost less than two dollars, and they take 30 seconds to install. It's the cheapest insurance against an oil leak you'll ever buy.
Tools and supplies you'll need
Gather these items before you start: a filter wrench sized for your housing (usually 74 mm or 76 mm for the 2017 Wrangler), a drain pan, clean rags, a plastic scraper or old credit card, the correct replacement filter and O-ring, fresh oil in the correct grade, and a jack or ramps if you're working in a driveway. If you're removing the wheel well liner, you'll also need a socket set or screwdriver to unbolt the clips.
A torque wrench is not necessary for this job—hand-tightening plus a three-quarter turn with the wrench is the correct method. If you don't own a filter wrench, you can rent one from most auto parts stores for a few dollars, or buy a universal wrench that fits multiple sizes. Do not attempt to remove the cap by hand alone; the housing is tight and you'll strip your hands before you loosen it.
Frequently Asked Questions
Can I change the oil filter without draining the oil?
Yes. The filter change and oil drain are separate jobs. You can replace just the filter and leave the old oil in the pan, though most people do both at the same time because you're already underneath the vehicle. If you change only the filter, you'll still need to check and top up the oil level afterward.
What happens if I over-tighten the filter cap?
Over-tightening crushes the O-ring and can strip the threads on the housing. If the threads are damaged, the cap won't seal properly no matter how tight you make it, and you'll have a leak. Tighten by hand until resistance, then use the wrench for three-quarter turn—that's enough.
How often should I change the filter on a 2017 Wrangler?
Jeep recommends changing the oil and filter every 10,000 miles or 12 months, whichever comes first. If you drive in dusty or towing conditions, change it every 5,000 miles. Check your owner's manual for the exact interval for your driving conditions.
Is the Mopar filter worth the extra cost over aftermarket?
Mopar filters are OEM and may provide to fit, but quality aftermarket filters from Fram, Motorcraft, or ACDelco work just as well and often cost less. The important thing is that the filter is rated for your engine size and has the correct thread and O-ring size. Cheap no-name filters are where you save money and create problems.
What should I do with the old filter?
Take it to an auto parts store or recycling center. Most stores accept used filters for free. Do not throw it in the trash—it still contains oil and is a hazardous waste item in most places.