The 2018 Camry uses a cartridge-style oil filter mounted on top of the engine

The 2018 Toyota Camry does not have a traditional spin-on oil filter. Instead, it uses a cartridge filter — a cylindrical element that sits inside a plastic housing on the top of the engine. This design is common on newer Toyota models and requires a different removal process than older vehicles.

The filter housing is located on the driver's side of the engine, near the back. You'll see a large black plastic cap with a wrench symbol on top. This cap unscrews to access the filter element inside. The whole job takes about 15 to 20 minutes if you're doing it yourself, or 30 to 45 minutes at a shop because they also drain and replace the oil.

Key Takeaways

  • The 2018 Camry's cartridge filter sits under a cap on top of the engine, not on the side like older models.
  • You need a filter wrench to remove the cap — a standard 74mm or 86mm cartridge filter socket works, or a strap wrench if you don't have the socket.
  • Toyota part number 04152-YZZA3 is the OEM filter; aftermarket equivalents from Fram, Mobil 1, and Bosch fit the same housing.
  • The filter change interval is every 10,000 miles or 12 months, whichever comes first, using Toyota 0W-20 synthetic oil.
  • Replacing the rubber O-ring seal on the cap every time you change the filter prevents oil leaks and costs less than $5.

What you need to buy and have on hand

You'll need the filter element itself, a replacement O-ring seal, and a tool to remove the cap. Toyota recommends using their cartridge filter socket (part number 09228-06001), which is a 74mm socket that fits a standard ratchet. If you don't own this socket, a strap wrench works as a substitute — it grips the cap without marring it. Do not use a regular adjustable wrench or pliers on the cap, as they will damage the plastic.

The OEM filter is Toyota part 04152-YZZA3. Aftermarket filters that fit the same housing include Fram TG10158, Mobil 1 M1-110, and Bosch 3323. All of these are cartridge-style filters designed for the same cap housing. The O-ring seal comes with most replacement filters, but if you buy a bulk filter, you'll need to order the seal separately — Toyota part 90301-10001 or a generic 70mm x 3mm nitrile O-ring.

Step-by-step removal and installation

Start with the engine cold or warm but not hot. Locate the filter cap on top of the engine — it's the large black plastic cylinder on the driver's side. Use your filter socket or strap wrench to turn the cap counterclockwise and unscrew it completely. The old filter element will come out with the cap.

Inspect the rubber O-ring seal that sits in the groove at the base of the cap. If it's cracked, hardened, or stuck to the engine, replace it now. Clean the sealing surface on the engine with a clean rag to remove any old oil or debris. Install the new O-ring by pressing it into the groove — it should sit flat and not twist.

Drop the new filter element into the housing, making sure it seats fully at the bottom. Screw the cap back on by hand until the O-ring contacts the engine, then use your wrench to tighten it an additional three-quarter turn. Do not over-tighten — the plastic cap can crack if you force it. Wipe away any spilled oil and start the engine to check for leaks around the cap.

Oil type and change interval for the 2018 Camry

The 2018 Camry requires Toyota 0W-20 synthetic oil regardless of engine size or driving conditions. The 2.5-liter four-cylinder and the 3.5-liter V6 both use the same viscosity. Toyota does not recommend 5W-20 or any other grade for this model year, so check your oil cap or owner's manual to confirm before you pour.

The oil capacity is 3.7 quarts for the four-cylinder and 3.5 quarts for the V6, but always check the dipstick after filling to reach the full mark. Change the oil and filter together every 10,000 miles or 12 months, whichever comes first. If you drive mostly short trips, in stop-and-go traffic, or in dusty conditions, Toyota recommends the 10,000-mile interval. Highway driving on longer trips can stretch to the full 12 months between changes.

Common mistakes that cause leaks or damage

The most frequent error is over-tightening the filter cap. The plastic housing can crack if you use a wrench to tighten beyond the three-quarter turn after the O-ring contacts the engine. This creates a leak that may not show up until the next day, and a cracked housing requires replacing the entire cap assembly — a $40 to $80 part plus labor.

The second mistake is forgetting to replace the O-ring seal. Reusing the old seal causes slow seeps that can go unnoticed for weeks. By the time you spot the leak, you may have lost enough oil to damage the engine. A new O-ring costs under $5 and takes 30 seconds to install, so replace it every time you change the filter.

A third issue is installing the filter element upside down or not seating it fully. The element has a rubber base that must face downward into the housing. Push it down firmly until you feel it stop — it should not rattle or move when you tap the cap. If it's not seated, the cap won't close properly and oil will leak when ready.

Where to get the filter and seal if you're not doing it yourself

Any Toyota dealership carries the OEM filter and O-ring in stock. A dealership oil change typically costs $50 to $75 and includes the filter, oil, and a fluid top-off check. Independent shops and quick-lube chains also stock cartridge filters for the Camry, though they may charge $35 to $60 for the service. Always confirm they're using 0W-20 synthetic oil before you leave.

If you're buying the filter yourself to have a shop install it, bring both the filter and the O-ring seal with you. Some shops will install customer-supplied filters, though a few charge a small fee ($5 to $10) for the service. Call ahead to ask their policy.

Frequently Asked Questions

Can I use a regular spin-on filter instead of the cartridge filter?

No. The 2018 Camry is designed for the cartridge filter system only. A spin-on filter will not fit the housing, and adapters are not recommended because they can cause pressure or flow problems. Stick with the cartridge filter specified in your owner's manual.

How tight should I turn the filter cap?

Hand-tighten the cap until the O-ring seal contacts the engine surface, then use a wrench to turn it an additional three-quarter turn (about 270 degrees). Do not turn it a full rotation or more — that over-tightens the plastic and risks cracking the housing. If you're unsure, err on the side of looser rather than tighter.

What happens if I don't replace the O-ring seal?

The old seal hardens and loses its grip over time. Oil will seep past it slowly, creating a leak that may not be obvious until you've lost a quart or more. A new O-ring costs under $5 and prevents this problem entirely, so it's worth replacing every time you change the filter.

Is there a difference between Toyota OEM filters and aftermarket filters for this model?

Both work fine in the 2018 Camry. OEM filters (Toyota part 04152-YZZA3) are slightly more expensive but may provide to fit perfectly. Aftermarket filters from Fram, Mobil 1, and Bosch are cheaper and perform equally well. The key is buying a cartridge filter rated for the Camry, not a spin-on filter.

Can I change the filter without changing the oil?

Technically yes, but it's not recommended. The filter and oil work together to keep the engine clean. If you change only the filter, the old oil continues to circulate with contaminants. Most shops change both together, and Toyota's maintenance schedule assumes you're doing both at the same time.