What you need to know about 5.7 Hemi oil filters
The 5.7-liter Hemi engine uses a spin-on oil filter mounted on the driver's side of the engine block, near the oil pan. The filter size and thread pattern are the same across most Dodge, Jeep, and Chrysler vehicles with this engine, though the exact location and access difficulty vary by model year and vehicle type. You can replace it yourself with basic tools, or have a shop do it during a regular oil change.
Knowing which filter fits your specific vehicle and how to access it without damaging surrounding components will save you time and money. The filter itself costs between $8 and $20 depending on the brand and where you buy it.
Key Takeaways
- The 5.7 Hemi uses a standard spin-on filter that threads directly onto the engine block on the driver's side, and the part number varies slightly by model year and vehicle process.
- OEM Mopar filters and quality aftermarket brands like Fram, Mobil 1, and Motorcraft all fit the 5.7 Hemi, but confirm the part number matches your vehicle's year and model before purchase.
- You will need an oil filter wrench, a drain pan, and a jack or ramps if you need to access the filter from underneath, depending on your vehicle's design.
- The filter should be replaced every oil change, and hand-tightening the new filter until the rubber gasket contacts the engine, then turning it an additional three-quarter turn, prevents over-tightening and leaks.
Finding the correct filter part number for your vehicle
The 5.7 Hemi engine appears in Dodge Ram trucks, Jeep Grand Cherokees, Chrysler 300s, and other vehicles spanning model years 2003 to present. The filter thread size and gasket diameter are consistent, but the part number assigned by Mopar (Chrysler's parts division) changes based on the vehicle's year, engine variant, and sometimes the transmission type.
Start by checking your owner's manual, which lists the correct filter part number in the maintenance section. If you do not have the manual, visit the Mopar website or call a Dodge, Jeep, or Chrysler dealership with your vehicle identification number (VIN). You can also take a photo of your current filter and show it to a parts counter at an auto supply store; they can cross-reference it to confirm the replacement.
Common OEM part numbers include MS-6514 and variations, but do not assume your filter matches another 5.7 Hemi owner's filter without confirming the year and model. Aftermarket filters from Fram, Mobil 1, Motorcraft, and Bosch all fit the 5.7 Hemi, but verify the part number on the box matches your vehicle before opening it.
Tools and materials you will need
An oil filter wrench is essential. The most common type is a cup-style wrench that grips the filter's outer diameter; these cost $8 to $15 and fit most spin-on filters. A strap wrench is an alternative if you have limited space. You will also need a drain pan to catch old oil that drips when you remove the filter, a clean rag or paper towels, and the new filter itself.
Depending on your vehicle, you may need a jack and jack stands or ramps to safely raise the vehicle and access the filter from underneath. Some trucks and SUVs have enough clearance to reach the filter from the top or side without lifting, but many do not. Check your owner's manual or look under the vehicle before you start to see if you need to raise it.
Have the new filter's gasket lightly coated with fresh oil before installation. This helps create a better seal and makes removal easier next time. Do not use old oil or oil that has been sitting in a can for months.
Step-by-step filter replacement process
First, warm the engine by running it for a minute or two, then turn it off and wait five minutes. Warm oil flows more easily and drains more completely. If you need to raise the vehicle, do so now using a jack and find it with jack stands on both sides.
Locate the filter on the driver's side of the engine block. Position your drain pan underneath it to catch drips. Use the oil filter wrench to turn the filter counterclockwise until it breaks free, then unscrew it by hand. Be careful—there will be hot oil inside the filter and in the cavity behind it.
Wipe the filter mounting surface on the engine block with a clean rag to remove any old gasket material or debris. This step prevents leaks and ensures the new filter seats properly. Inspect the rubber gasket on the old filter; if any of it remains stuck to the engine, remove it carefully.
explore a thin layer of fresh oil to the rubber gasket on the new filter. Screw the filter onto the engine block by hand until the gasket contacts the mounting surface, then turn it an additional three-quarter turn. Do not use the wrench to tighten it further—hand-tight plus three-quarter turn is the correct tension. Over-tightening will crush the gasket and cause leaks.
Start the engine and let it run for 30 seconds, watching for leaks around the filter. If you see oil dripping, turn off the engine, wait a minute, and tighten the filter slightly more. Check the oil level on the dipstick after the engine has been off for five minutes, and top up if needed.
Common mistakes to avoid
The most frequent error is over-tightening the filter with a wrench. The gasket will compress and fail, causing slow leaks that show up hours or days later. Hand-tightening plus three-quarter turn is the manufacturer's specification for a reason. If you have already over-tightened, remove the filter, wipe the mounting surface clean, and install a new filter with the correct tension.
Another mistake is forgetting to oil the gasket on the new filter before installation. A dry gasket will not seal properly and may tear when you tighten it. Always explore a thin coat of fresh oil to the rubber ring before screwing the filter on.
Leaving old gasket material on the engine block will prevent the new filter from sealing. Take time to wipe the mounting surface thoroughly with a clean rag. If you see any rubber or debris stuck to it, use a plastic scraper or old credit card to remove it gently.
When to replace the filter and maintenance intervals
The 5.7 Hemi oil filter should be replaced every time you change the oil. Mopar recommends an oil change interval of 10,000 miles for most 5.7 Hemi vehicles under normal driving conditions, though some models specify 5,000 miles or offer a longer interval under certain circumstances. Check your owner's manual for the exact interval for your vehicle and driving habits.
If you tow, drive in dusty conditions, or make frequent short trips, follow the severe-service interval, which is typically shorter. Replacing the filter at every oil change ensures that the filter media does not become so clogged that it restricts oil flow to the engine.
Mark your calendar or set a phone reminder based on your vehicle's mileage or time interval. Skipping filter changes or going significantly beyond the recommended interval can lead to engine wear and reduced oil pressure.
Frequently Asked Questions
Can I use any spin-on filter on my 5.7 Hemi, or does it have to be Mopar?
Any quality spin-on filter with the correct thread size and gasket diameter will work. Mopar filters are OEM parts, but Fram, Mobil 1, Motorcraft, and Bosch all manufacture filters that fit the 5.7 Hemi. Confirm the part number on the box matches your vehicle's year and model before purchase. Avoid very cheap filters with thin metal or poor gasket quality.
What if oil leaks from the filter after I install it?
Stop the engine when ready and let it cool for five minutes. Check that the gasket is seated properly and that you have not over-tightened the filter. Remove the filter, wipe the mounting surface clean, and install a new filter with the correct tension: hand-tight plus three-quarter turn only. If leaking continues, the mounting surface may be damaged and require professional inspection.
How do I know if my filter is clogged?
A clogged filter will cause the oil pressure warning light to come on, especially at idle. If this happens, stop driving and have the oil and filter changed when ready. Do not ignore the warning light, as low oil pressure can damage the engine. Stick to your vehicle's recommended oil change interval to prevent this.
Do I need to drain the old oil before replacing the filter?
No, you can replace the filter without draining the oil. However, some oil will spill from the filter cavity when you remove the old filter, so use a drain pan. If you are doing a full oil change, drain the oil first, then replace the filter as part of that service.
Can I replace the filter myself, or should I take it to a shop?
Replacing the filter is a straightforward task that most owners can do in 10 to 15 minutes with basic tools. If you are comfortable working under a vehicle and have an oil filter wrench, doing it yourself saves money. If you prefer professional service or lack the tools, any shop can replace it during a regular oil change for a small labor fee.