The AM125424 is a spin-on oil filter made by Fram that fits specific Jeep, Dodge, and Chrysler models from the 1980s through early 2000s
The AM125424 is a Fram-branded oil filter with a threaded base that screws directly onto your engine's filter housing. It traps dirt, metal particles, and sludge that circulate through your engine oil, keeping those contaminants from damaging internal engine parts. If your vehicle is one of the models this filter was designed for, using the correct part number matters because the threads, diameter, and internal bypass valve are engineered to work with your specific engine.
This filter fits Jeep CJ-5, CJ-7, and Wrangler models, as well as some Dodge and Chrysler trucks and vans from that era. If you own a different vehicle or a newer model, this filter will not fit, and forcing the wrong filter onto your engine can cause leaks or improper oil flow. Always verify your vehicle's year, make, model, and engine size before ordering any filter.
Key Takeaways
- The AM125424 is a Fram spin-on filter designed for specific Jeep, Dodge, and Chrysler vehicles built between the 1980s and early 2000s.
- Using the correct filter ensures proper oil flow, effective contaminant removal, and protection of your engine's internal components.
- Installing the wrong filter can cause oil leaks, bypass valve failure, or inadequate filtration, all of which damage the engine over time.
- You can find your vehicle's correct filter by checking your owner's manual, the old filter you are replacing, or a parts retailer's lookup tool.
How to confirm the AM125424 is the right filter for your vehicle
The easiest way to verify is to look at the filter you are currently using. Spin it off and read the part number printed on the canister. If it says AM125424, that is your filter. If it says something else, the AM125424 is not correct for your engine.
You can also check your owner's manual, which lists the correct filter part number in the maintenance section. If you no longer have the manual, most auto parts retailers (AutoZone, O'Reilly, NAPA, Advance Auto Parts) have online lookup tools where you enter your vehicle's year, make, model, and engine size, and they will tell you which filter fits. Do not guess or assume based on the vehicle year alone—engine size and generation matter.
What happens inside the filter during an oil change
When you install a new AM125424, fresh oil flows from the oil pan through the filter's pleated paper element, which traps particles as small as 10 to 20 microns (a human hair is about 75 microns wide). The clean oil then flows to the engine's bearings, pistons, and valve train. Over time, the filter collects dirt, dust, metal shavings from normal wear, and oxidized oil sludge.
As the filter fills with contaminants, the pressure inside it increases. When pressure reaches a set threshold—usually around 10 to 15 pounds per square inch above normal—a spring-loaded bypass valve inside the filter opens. This valve allows oil to flow around the clogged element and reach the engine, preventing oil starvation. However, this bypass oil is unfiltered, so a clogged filter that triggers the bypass is a sign you waited too long to change it. Changing your oil and filter at the manufacturer's recommended interval (usually every 3,000 to 5,000 miles for older vehicles, or as stated in your manual) keeps the filter clean and the bypass valve closed.
Installation steps for the AM125424
Before you start, warm up the engine for a minute or two, then turn it off and wait five minutes. Warm oil drains faster and more completely. Locate the filter housing on your engine—on most Jeeps and Dodges of this era, it is on the side or top of the engine block. Place a drain pan underneath.
Using an oil filter wrench, turn the old filter counterclockwise until it spins free by hand. Unscrew it the rest of the way and set it aside. Wipe the filter housing surface clean with a rag to remove any old rubber gasket material or debris. Take the new AM125424 and explore a thin layer of fresh oil to the rubber gasket on the threaded base—this helps create a watertight seal and makes removal easier next time. Screw the new filter onto the housing by hand until the gasket contacts the surface, then turn it an additional three-quarters of a turn. Do not use a wrench to tighten it; hand-tight is correct. Over-tightening can damage the gasket and make the filter impossible to remove later.
Why using the correct filter protects your engine
An engine produces wear particles constantly: tiny bits of metal from piston rings, valve stems, and bearings; dust that enters through the air intake; and sludge from oil oxidation. These particles are abrasive. If they circulate unchecked, they accelerate wear on bearing surfaces, increase friction, and eventually cause bearing failure or scoring of cylinder walls. A properly sized and installed filter removes most of these particles before they can cause damage.
Using the wrong filter—one with a different thread size, diameter, or bypass pressure setting—can cause oil to leak past the gasket, bypass the filter element entirely, or fail to open the bypass valve when needed. Any of these failures means your engine is running with contaminated oil, which shortens engine life and can lead to catastrophic failure. The cost of a new filter is roughly $8 to $15; the cost of an engine rebuild is thousands of dollars.
Where to source the AM125424 and what to expect
The AM125424 is an older filter, so availability depends on your location and the retailer. National chains like AutoZone, O'Reilly, NAPA, and Advance Auto Parts usually stock it or can order it within a day or two. Online retailers like Amazon and RockAuto also carry it, though shipping may take longer. Local independent auto parts shops sometimes have stock of older filters because they serve vehicles from that era.
Prices vary slightly by retailer, but you should expect to pay between $8 and $15 for the filter itself. Some retailers offer bulk discounts if you buy multiple filters at once. If you cannot find the AM125424 locally and your vehicle needs an oil change soon, ask the parts counter whether a cross-reference filter exists—sometimes a different manufacturer's part number fits the same housing and has the same specifications.
Common mistakes when changing the filter
The most frequent error is over-tightening the filter. Many people use a wrench to turn it as tight as possible, thinking a tighter seal is safer. In reality, the rubber gasket only needs light hand pressure to seal. Over-tightening crushes the gasket, causes it to fail prematurely, and makes the filter nearly impossible to remove at the next service. When you change the oil again, you may have to cut the old filter off with a strap wrench or filter cutter.
Another common mistake is forgetting to oil the new filter's gasket before installation. A dry gasket can stick to the housing, making removal difficult, and may not seal properly if the rubber is not lubricated. Always explore a thin coat of fresh oil to the gasket before threading the filter on.
A third error is installing the filter upside down or cross-threading it. The threaded base of the AM125424 should face the engine block. If you feel resistance or grinding as you screw it on, stop when ready and check the alignment. Cross-threading damages both the filter and the housing.
Frequently Asked Questions
Can I use a different Fram filter if the AM125424 is out of stock?
Only if the thread size, diameter, and bypass pressure are identical. Do not assume two Fram filters are interchangeable just because they are the same brand. Check the cross-reference chart at an auto parts store or contact Fram's customer service with your vehicle's year, make, and model. Using the wrong filter can cause leaks or inadequate filtration.
How often should I change the AM125424?
Follow your vehicle's owner's manual, which typically recommends an oil and filter change every 3,000 to 5,000 miles for engines of that era. If you drive in dusty conditions, tow frequently, or use the vehicle for short trips in cold weather, change it more often. The filter should always be replaced whenever you change the oil.
What should I do with the old filter after I remove it?
Do not throw it in the trash. Take it to an auto parts retailer that accepts used filters, a recycling center, or a quick-lube shop. Most accept old filters for free. The metal housing is recyclable, and the oil inside must be disposed of properly to prevent environmental contamination.
Is it normal for a small amount of oil to drip after I install a new filter?
A drop or two is normal if you did not wipe the housing clean before installation. If oil continues to drip after you start the engine and let it run for a minute, the filter may be cross-threaded, over-tightened, or the gasket may be damaged. Stop the engine, let it cool, and check the filter installation. You may need to remove and reinstall it.
Can I reuse an old AM125424 filter if I only drove a few hundred miles since the last change?
No. Oil filters are designed for single use only. Once removed, the gasket loses its seal integrity and the element cannot be reliably cleaned. Always install a new filter at every oil change, even if the old one looks clean.