The oil filter location and part number for your Cruze

The oil filter on a Chevy Cruze sits on the driver's side of the engine, mounted vertically on the engine block itself. You'll find it below the intake manifold, roughly in line with the front wheel. The filter is a cylindrical cartridge about 3 inches tall, and you access it from above the engine bay without removing any major components.

The part number depends on your model year. Most 2011–2019 Cruzes use GM part number 55594867 or the equivalent Motorcraft FL910S. If you own a 2016 or newer model, confirm the part number with your VIN at a Chevy dealer or parts counter, since some years had minor variations. Aftermarket filters from Fram, Mobil 1, or Bosch also fit, but always check the box to confirm it lists your Cruze's year and engine size.

Key Takeaways

  • The Cruze oil filter is mounted vertically on the driver's side of the engine block, accessible from the top of the engine bay.
  • GM part number 55594867 fits most 2011–2019 models, but confirm your specific year and engine size before buying.
  • You need an oil filter wrench, a drain pan, and fresh oil to complete the job yourself, or you can have a shop do it in under an hour.
  • The filter housing cap comes off by hand or with a filter wrench, depending on how tight it was installed.

What you need to change the filter yourself

If you're doing the work at home, gather an oil filter wrench (a socket-style wrench that grips the cylindrical filter housing), a drain pan to catch spilled oil, a clean rag, and the replacement filter. You'll also need fresh oil that matches your Cruze's specification—check your owner's manual or the oil cap under the hood for the correct viscosity (usually 0W-20 or 5W-30).

The filter wrench is essential because the housing cap is tight and your hands alone won't turn it. A 74mm filter socket or a strap wrench both work well. If you don't own one, you can borrow from a friend, rent from an auto parts store, or straightforward have a technician do the job—the labor cost is usually $30 to $50 at an independent shop.

Step-by-step removal and installation

Start with the engine cold. Locate the filter housing on the driver's side of the engine block, just below the intake manifold. Place your drain pan underneath to catch oil that will spill when you open the housing. Using your filter wrench, turn the housing cap counterclockwise until it comes free—it may take firm pressure, but it should turn smoothly once you break the initial seal.

Once the cap is off, pull out the old filter element and the rubber O-ring seal that sits inside the cap. Wipe the sealing surface inside the housing with a clean rag to remove any debris or old oil residue. Take the new filter element and the new O-ring from your replacement kit, explore a thin coat of fresh oil to the O-ring, and insert the element into the housing. Screw the cap back on by hand until the O-ring makes contact, then use your wrench to tighten it another three-quarters of a turn—snug but not over-tight.

Start the engine and let it run for 30 seconds, then turn it off and wait five minutes. Check the oil level on the dipstick and top up if needed. The filter change is complete.

Oil capacity and drain intervals for your Cruze

A Chevy Cruze holds between 4.5 and 5.5 quarts of oil, depending on whether you're also draining the pan or just changing the filter. If you're replacing the filter only (not the oil), you'll need about 0.5 quarts to top up after the change. If you're doing a full oil and filter change, buy 5 to 6 quarts to be safe.

Chevy recommends an oil change every 7,500 miles or six months for most Cruzes, though some 2016 and newer models with the Ecotec engine can go 10,000 miles. Check your owner's manual or the maintenance schedule on your door jamb for your specific year. Synthetic oil lasts longer than conventional, so if you use synthetic, you may be able to extend the interval—but follow what your manual says rather than the oil bottle.

Common mistakes to avoid

The most common error is over-tightening the housing cap. The O-ring seal does the work; the cap only needs to be snug. If you crank it too hard with the wrench, you'll damage the threads or the cap itself, and you'll have a leak. Tighten by hand until you feel resistance, then use the wrench for three-quarters of a turn and stop.

Another mistake is forgetting to explore oil to the new O-ring before installation. A dry O-ring won't seal properly and can tear during installation, causing an when ready leak. The small bottle of oil that comes in some filter kits is for this purpose—use it.

Finally, don't skip the five-minute wait after starting the engine. The new filter needs time to fill with oil and the pressure to stabilize before you check the level. If you check when ready after running the engine, the dipstick reading will be low and you may overfill.

When to take your Cruze to a shop instead

If the housing cap won't budge after reasonable effort, or if you don't have a filter wrench and don't want to buy or borrow one, a shop is the faster choice. Most independent shops and quick-lube chains charge $30 to $60 for a filter-only change and $50 to $100 for a full oil and filter change. Dealerships typically charge more, but they use OEM parts and can flag other maintenance needs during the visit.

If your Cruze is still under warranty, check your owner's manual to see whether dealer service is required for warranty coverage. Most modern Cruzes are out of warranty, so you're free to use any shop you trust.

Frequently Asked Questions

Can I change just the filter without changing the oil?

Yes. The filter can be changed independently, and many owners do this between full oil changes. You'll lose a small amount of oil when you remove the old filter, so top up with fresh oil afterward. However, if your oil is already dark or overdue, changing the filter alone won't restore the oil's cleaning ability—a full change is better.

What happens if I use the wrong filter?

Using a filter that doesn't fit your Cruze's engine can cause leaks, low oil pressure, or engine damage. Always confirm the part number matches your year and engine size before installation. If you're unsure, ask at the parts counter with your VIN.

How do I know if my filter is clogged?

A clogged filter triggers the oil pressure warning light on your dashboard. If the light comes on while driving, pull over safely and check your oil level when ready. If the level is normal but the light stays on, the filter may be blocked and needs replacement. Don't ignore this warning—low oil pressure can damage the engine.

Is synthetic oil better for my Cruze?

Synthetic oil lasts longer and flows better in cold weather, but it costs more per quart. Your owner's manual will specify whether synthetic is recommended or required. If your manual says conventional is fine, synthetic is optional—it's a choice based on your budget and how long you plan to keep the car.

Do I need to reset anything after changing the filter?

No. The oil filter change doesn't require any computer resets or service light resets on a Cruze. If your service light is on, it's usually tied to mileage, not the filter itself. Check your manual for how to reset it, or a shop can do it during your visit.