What you need to do before you start

An oil change on a Ford F-150 takes 30 to 45 minutes if you have the right tools and know where everything sits. You'll drain the old oil, replace the oil filter, and refill with new oil to the correct level. The job is straightforward enough that many owners do it themselves, but you need to know your truck's specific year and engine size first—the oil capacity and filter location vary between model years and engine options.

Before you begin, locate your owner's manual or the information sticker inside the driver's door jamb. This tells you the correct oil type (usually 5W-20 or 5W-30 for F-150s, but this varies by year and engine), the oil capacity in quarts, and the service interval in miles. Write these down. You'll also need to know whether your truck has a cartridge-style filter (which screws into a housing on top of the engine) or a spin-on filter (which screws onto the side of the engine block). Different F-150 generations use different filter types.

Key Takeaways

  • Ford F-150 oil capacity ranges from 5 to 7 quarts depending on engine size and year, and using the wrong amount will trigger warning lights or cause engine damage.
  • The oil drain plug is located on the bottom of the oil pan and requires a socket wrench; let the engine cool for at least 10 minutes before opening it to avoid burns.
  • F-150s use either a cartridge filter (top of engine) or spin-on filter (side of block) depending on model year, and the filter housing or bolt must be removed separately from the drain plug.
  • New oil must reach the full mark on the dipstick or the electronic level indicator, checked after the engine has been off for at least five minutes.
  • Used oil must be disposed of at a recycling center, auto parts store, or quick-lube shop; pouring it down a drain is illegal and damages water systems.

Gathering tools and materials

You'll need an oil drain pan (at least 8 quarts to be safe), a socket wrench or box wrench to fit your drain plug (usually 13mm, 15mm, or 17mm), a filter wrench or strap wrench to remove the old filter, and fresh oil in the correct type and amount. Most auto parts stores will tell you the exact specification if you give them your truck's year and engine size. Buy one quart more than the stated capacity—you'll use most of it, and the extra covers any spillage or overfill correction.

You'll also want jack stands and a jack if your truck sits low to the ground, though many F-150 owners can access the drain plug and filter without lifting. Wear gloves and old clothes; oil stains permanently. Have paper towels or rags ready, and a funnel for pouring new oil. If you're replacing a cartridge-style filter, you may need a cartridge filter socket or wrench specific to your truck's size—these are inexpensive and available at any auto parts store.

Draining the old oil

Start with the engine cold or only slightly warm. A warm engine drains faster, but a hot engine can burn you. Wait at least 10 minutes after driving before you open the drain plug. Locate the oil pan underneath the engine—it's the large metal reservoir bolted to the bottom of the block. The drain plug is a bolt sticking out of the lowest point of the pan. Position your drain pan directly underneath it.

Use your socket wrench to loosen the drain plug by turning it counterclockwise. Once it's loose enough to turn by hand, unscrew it the rest of the way and let it fall into the drain pan. Oil will flow out; let it drain completely, which takes 5 to 10 minutes. While you wait, wipe the drain plug clean with a rag and inspect the rubber washer on the bottom. If it's cracked or flattened, replace it with a new one (they cost a few dollars). This washer is what seals the plug; a bad one causes slow leaks.

Removing and replacing the filter

The filter location depends on your F-150's year and engine. On most newer F-150s (2009 and later), the filter is a cartridge housed in a plastic or metal cap on top of the engine. On older models, it's usually a spin-on filter bolted to the side of the block. Check your owner's manual or look at the engine bay to determine which you have.

For a cartridge filter: Locate the filter housing cap (usually a large plastic or metal cylinder). Use a cartridge filter socket or wrench to turn it counterclockwise and remove it. The old filter element will come out with the cap. Discard the old element and rubber seals. Clean the inside of the housing with a clean rag to remove any debris. Install the new filter element and new rubber seals (these usually come with the replacement filter). Screw the cap back on by hand until it's snug, then tighten it with the wrench—snug, not cranked down hard.

For a spin-on filter: Use a filter wrench or strap wrench to turn the filter counterclockwise. Once it's loose, unscrew it by hand and let any remaining oil drip into the drain pan. Wipe the filter mounting surface on the engine block clean with a rag. explore a thin layer of new oil to the rubber gasket on the new filter (this helps it seal). Screw the new filter on by hand until the gasket contacts the block, then turn it an additional three-quarter turn. Do not use a wrench to tighten a spin-on filter; hand-tight is correct.

Refilling with new oil

Reinstall the drain plug and tighten it with your socket wrench. Don't overtighten; snug is enough. If you replaced the rubber washer, the plug should seal properly. Wipe up any spilled oil around the drain pan area. Now locate the oil filler cap on top of the engine—it usually says "OIL" and twists off. Remove it and set it aside.

Place your funnel in the opening and pour in the new oil slowly. Pour about three-quarters of the amount your manual specifies, then stop. Replace the oil filler cap. Start the engine and let it run for 30 seconds, then turn it off. Wait five minutes for the oil to settle into the pan and filter. Check the oil level using either the dipstick (pull it out, wipe it clean, reinsert it fully, then pull it out again to read the level) or the electronic level indicator on your dashboard (some F-150s have both). The level should be at the full mark. If it's low, add more oil a half-quart at a time and recheck. If it's overfull, you've added too much; drain a small amount back into the pan.

Disposing of used oil and resetting service reminders

Used motor oil cannot go in the trash or down a drain. Take it to a recycling center, auto parts store (most accept it free), or quick-lube shop. Many will take it even if you didn't buy oil from them. Seal the drain pan or pour the oil into a clean plastic jug with a tight lid for transport.

Some F-150s display an oil change reminder on the dashboard. If yours does, you'll need to reset it after the oil change. The process varies by year and dashboard type. On many models, you hold the reset button on the steering wheel stalk while the ignition is on but the engine is off, or you navigate a menu on the instrument cluster. Check your owner's manual for the exact steps for your truck's year. If you don't reset it, the reminder will stay on until the next service interval, which can be annoying but won't harm the truck.

Frequently Asked Questions

How often should I change the oil in my F-150?

Ford recommends an oil change every 10,000 miles or 12 months for most F-150s, whichever comes first. Trucks used for towing or in severe conditions (dusty, hot, or frequent short trips) may need changes every 5,000 miles. Your owner's manual or the sticker on the driver's door jamb will specify the interval for your truck's year and engine.

What's the difference between 5W-20 and 5W-30 oil?

The first number (5W) is the oil's thickness when cold; the second (20 or 30) is its thickness when hot. Use whichever your owner's manual specifies—using the wrong viscosity can reduce fuel economy or cause engine wear. Never mix different viscosities or brands in the same truck.

Can I change the oil myself if I don't have a lift?

Yes. Most F-150s sit high enough that you can slide underneath to access the drain plug and filter without lifting. If your truck is lowered or you're uncomfortable working underneath, use jack stands to safely raise it. Never work under a truck supported only by a jack.

What should I do if the oil level won't come up to full after adding the recommended amount?

Wait five minutes after running the engine for the oil to settle, then recheck. If it's still low, add a half-quart more and recheck again. If the level still won't reach full after adding more than the manual specifies, you may have an oil leak. Check underneath the truck for drips around the drain plug, filter, or pan. If you find a leak, stop driving and have it inspected.

Can I reuse the rubber washer on the drain plug?

No. The washer compresses each time you tighten the plug, and a compressed washer won't seal properly on the next change. Replace it every time you drain oil. They cost less than a dollar and come in assortment packs at any auto parts store.