What happens when you change your engine oil
An engine oil change means draining the old oil from your engine, replacing the oil filter, and filling the engine with fresh oil. The old oil has picked up dirt, metal particles, and moisture over months of running your engine. Fresh oil lubricates moving parts, reduces friction, and helps your engine run cooler and last longer.
You can do this work yourself in a driveway or garage, or take your vehicle to a shop. The job takes 30 minutes to an hour if you have done it before, longer if this is your first time. You will need basic tools, a safe way to lift the vehicle, and a place to dispose of the old oil responsibly.
Key Takeaways
- Drain the old oil while the engine is warm but not hot, then replace the oil filter before refilling with the correct type and amount of new oil.
- Your owner's manual tells you the exact oil type, viscosity grade, and capacity your engine needs — do not guess or use what worked for someone else's vehicle.
- You will need a wrench, oil filter wrench, oil drain pan, jack and jack stands (or ramps), and a way to dispose of old oil at a recycling center or auto parts store.
- Check your oil level with the dipstick after the engine has sat for five minutes, and top up if needed before driving.
- Most vehicles need an oil change every 5,000 to 10,000 miles, but check your owner's manual for your specific interval.
Gather the right tools and materials before you start
Before you lift the vehicle, collect everything you will need. You need an oil drain pan large enough to hold all the old oil without spilling, a wrench that fits your drain plug, an oil filter wrench sized for your filter, a new oil filter, and new oil in the type and amount your manual specifies. You also need a way to safely lift and support the vehicle — either a floor jack with jack stands or ramps rated for your vehicle's weight.
Have shop towels or old rags on hand to wipe spills and check the dipstick. If you do not own an oil filter wrench, you can buy one for $10 to $20, or some auto parts stores will loan one free if you buy oil from them. Do not skip the jack stands — a vehicle supported only by a jack can slip and cause serious injury.
Lift the vehicle safely and locate the drain plug
Park on level ground and engage the parking brake. If using a floor jack, position it under a frame point (not the plastic undercarriage), lift the vehicle, and place jack stands under solid frame points on both sides. Lower the vehicle onto the stands and verify it is stable before getting underneath. If using ramps, drive slowly up both ramps and set the parking brake.
Locate the oil drain plug underneath the engine — it is a bolt sticking down from the oil pan. Consult your owner's manual if you cannot find it. Place the drain pan directly under the plug. Loosen the plug with your wrench by turning counterclockwise, then unscrew it by hand once it is loose enough. Oil will flow out, so be ready. Let the oil drain completely — this takes 5 to 10 minutes. Wipe the drain plug clean with a rag and reinstall it, tightening it snugly but not so hard that you strip the threads.
Remove and replace the oil filter
The oil filter is a cylindrical canister bolted or screwed onto the engine block. Locate it using your manual. Position the drain pan underneath it to catch residual oil. Use your oil filter wrench to loosen the filter by turning counterclockwise, then unscrew it by hand. Some oil will spill, so work slowly. Once removed, wipe the filter mounting surface on the engine clean with a rag.
Take your new filter and coat the rubber gasket (the ring on top) lightly with fresh oil. This helps the gasket seal properly. Screw the new filter on by hand until the gasket touches the engine, then turn it an additional three-quarter turn. Do not use the wrench to tighten it — hand-tight is correct. Over-tightening makes the filter hard to remove next time and can damage the gasket.
Lower the vehicle and refill with new oil
Lower the vehicle back to the ground using the jack, or back slowly down the ramps. Locate the oil filler cap on top of the engine — it usually has an oil can symbol. Unscrew it and set it aside. Place a funnel in the opening and pour in the amount of new oil specified in your owner's manual. Start with slightly less than the full amount, then check the level before adding the final bit.
Screw the oil filler cap back on. Start the engine and let it run for 30 seconds to circulate the new oil through the filter and engine. Turn it off and wait five minutes for the oil to settle back into the pan. This waiting period is important — if you check the level when ready after running the engine, the reading will be inaccurate.
Check the oil level and dispose of old oil properly
After waiting five minutes, pull out the dipstick, wipe it clean with a rag, reinsert it fully, then pull it out again to read the level. The dipstick has marks showing the minimum and maximum levels. The oil should be at or near the maximum mark. If it is below the minimum, add a small amount of oil and recheck. If it is above the maximum, you have overfilled — drain a little out through the drain plug.
Do not pour old oil down a drain, into the ground, or into the trash. Take it to a recycling center, auto parts store, or quick-lube shop — most accept old oil for free or a small fee. Many stores that sell oil will take it back. Seal the drain pan or pour the oil into a clean container with a tight lid before transport.
Common mistakes to avoid
Using the wrong oil type or viscosity is the most common error. Your owner's manual specifies the exact grade — for example, 5W-30 or 10W-40. The numbers matter. Using a thinner oil than recommended can cause engine wear; using a thicker oil can make cold starts difficult and reduce fuel economy. If you are unsure, call your vehicle's manufacturer or consult the manual.
Overfilling the oil is another frequent mistake. Too much oil can damage the engine by creating excess pressure and foaming. Underfilling starves the engine of lubrication. Always check the level with the dipstick after the engine has cooled and settled. Do not rely on the amount you poured in — different engines hold different amounts, and some oil remains in the old filter.
Forgetting to replace the drain plug washer is straightforward to overlook. Many drain plugs have a small crush washer that seals the plug. If your plug has one, replace it with a new washer each time. A worn washer can cause slow leaks. Also, do not overtighten the drain plug — you can strip the threads in the aluminum oil pan, which is expensive to repair.
When to change your oil and what to track
Check your owner's manual for the recommended oil change interval for your vehicle. Older vehicles often needed changes every 3,000 miles, but modern engines with synthetic oil can go 7,500 to 10,000 miles or longer between changes. Some newer vehicles use oil-life monitoring systems that calculate when a change is due based on driving conditions. If your vehicle has this system, follow the dashboard message rather than a fixed mileage interval.
Keep a record of each oil change — the date, mileage, oil type used, and filter type. This log helps you remember when the next change is due and provides proof of maintenance if you sell the vehicle. Write the date on the new filter with a marker before installation so you can see at a glance when it was last changed.
Frequently Asked Questions
Can I change my oil if the engine is cold?
Cold oil drains slowly and incompletely, leaving more old oil in the pan. Warm oil flows faster and drains more thoroughly. Start the engine, let it run for a minute or two, then turn it off and wait a few minutes before draining. The oil should be warm but not so hot that you cannot touch the drain pan safely.
What should I do if I spill oil on the driveway?
Clean it up when ready with absorbent material like kitty litter, sand, or oil absorbent pads. Sweep up the material and dispose of it in the trash. Do not hose it down — oil runs into storm drains and harms waterways. For large spills, contact your local environmental agency for guidance.
Is synthetic oil better than conventional oil?
Synthetic oil lasts longer between changes and performs better in extreme temperatures, but it costs more per quart. Conventional oil is cheaper and works fine if you change it at the recommended interval. Your owner's manual specifies which type your engine requires or recommends — follow that guidance rather than choosing based on price alone.
How do I know if I have the right oil filter?
The filter part number is printed on the side of the old filter. Take the old filter to an auto parts store and match the number, or look up your vehicle's year, make, and model in the store's system. Filters are inexpensive — buying the correct one takes five minutes and prevents leaks or bypass problems.
What if oil leaks from the drain plug after I reinstall it?
The drain plug washer may be worn or missing. Turn off the engine, let it cool, and remove the drain plug again. Check whether a washer is present. If not, install a new crush washer before reinstalling the plug. If a washer is present but the leak continues, the threads may be stripped — take the vehicle to a shop to have the pan repaired or replaced.