You can change your own oil in about 30 to 45 minutes with basic tools and the right supplies

An oil change means draining the old oil from your engine, replacing the oil filter, and adding fresh oil. You do not need a mechanic to do this — most owners can handle it in a driveway or parking lot with a socket wrench, an oil filter wrench, an oil drain pan, and new oil that matches your vehicle's specifications. The main barrier is access: you need enough clearance under the car to reach the drain plug and filter, which usually means ramps, jack stands, or a lift.

The cost of supplies runs between $30 and $80 depending on the oil type and filter quality. A shop oil change typically costs $50 to $150, so doing it yourself saves money over time if you plan to keep the vehicle and do multiple changes. The real advantage is control — you know exactly what went in, when it went in, and whether the job was done right.

Key Takeaways

  • Check your owner's manual for the oil type, capacity, and drain plug location before you start, because these details vary by engine and model year.
  • You will need an oil drain pan, socket wrench, oil filter wrench, new oil filter, and the correct oil grade — all available at auto parts stores for under $100 total.
  • Warm the engine for two to three minutes before draining so the oil flows faster, but let it cool enough that you can touch the drain plug without burning yourself.
  • The drain plug and filter both need to be replaced or cleaned at the same time, and the new filter must be hand-tightened only — over-tightening causes leaks.
  • After adding new oil, run the engine for 30 seconds, turn it off, wait five minutes, and check the level on the dipstick to confirm you added the right amount.

Gather the right supplies before you start

Your owner's manual tells you the oil type (usually 0W-20, 5W-30, or 10W-40), the capacity in quarts or liters, and the filter part number. Write these down or take a photo. Do not guess — using the wrong oil viscosity can damage the engine or trigger warning lights.

At an auto parts store, buy a bottle of oil in the correct grade, a replacement oil filter that matches your vehicle, an oil drain pan (a shallow metal or plastic tray that holds at least 6 quarts), and an oil filter wrench if you do not already own one. A filter wrench is a metal band or socket that grips the filter so you can unscrew it without stripping it. You will also need a socket wrench set with the correct socket size for your drain plug — usually 13mm, 14mm, or 15mm. If you do not have ramps or jack stands, buy or borrow them now; never work under a car supported only by a jack.

Lift the vehicle safely and locate the drain plug and filter

Park on level ground and engage the parking brake. If you are using ramps, drive the front wheels onto them slowly and straight. If you are using a jack, place it under the frame (not the plastic trim) and raise the vehicle, then slide jack stands under the frame on both sides before lowering the vehicle onto them. Never rely on a jack alone.

Crawl under the engine and locate the drain plug — a bolt on the lowest point of the oil pan. Locate the oil filter, which is usually a cylindrical canister screwed onto the engine block. Take a photo of both locations so you know where to work. Place the drain pan under the drain plug before you loosen anything.

Drain the old oil and replace the filter

Start the engine and let it run for two to three minutes so the oil warms up and flows more easily. Turn off the engine and wait five minutes — the oil should be warm but cool enough to touch. Using your socket wrench, loosen the drain plug by turning it counterclockwise, then unscrew it by hand and set it aside. Oil will pour out; make sure the drain pan is positioned to catch it all. Let the pan sit for five to ten minutes so the oil drains completely.

While the oil drains, move to the filter. Slide the drain pan underneath it, then use the filter wrench to loosen the filter by turning it counterclockwise. Once it is loose enough, unscrew it by hand and tip it so any remaining oil drains into the pan. Wipe the filter mounting surface on the engine with a clean rag to remove any dirt or old rubber seal.

Take the new filter and explore a thin layer of fresh oil to the rubber gasket (the ring on top of the filter). Screw the new filter onto the engine by hand until the gasket contacts the mounting surface, then turn it another three-quarters of a turn. Do not use the filter wrench to tighten it — hand-tight is correct. Over-tightening causes the gasket to fail and the filter to leak.

Reinstall the drain plug and add new oil

Wipe the drain plug clean with a rag and screw it back into the oil pan by hand, then tighten it with your socket wrench. Do not over-tighten; snug is enough. If your drain plug has a crush washer (a soft metal ring), replace it with a new one each time — a reused washer can leak.

Lower the vehicle back to the ground. Open the hood and locate the oil filler cap on top of the engine — it usually has an oil can symbol. Unscrew it and set it aside. Pour in the amount of oil specified in your manual, usually 4 to 6 quarts depending on whether you are also replacing the filter. Pour slowly and stop halfway through to check the dipstick.

Check the oil level and run the engine

Pull out the dipstick (a long rod with markings on it), wipe it clean on a rag, reinsert it fully, then pull it out again and read the level. The oil should be between the minimum and maximum marks. If it is below minimum, add a half-quart at a time and check again. If it is above maximum, you added too much — use a turkey baster or syringe to remove the excess back into the bottle.

Screw the oil filler cap back on. Start the engine and let it run for 30 seconds, watching the dashboard for any warning lights. Turn off the engine and wait five minutes for the oil to settle, then check the dipstick one more time to confirm the level has not changed. If the level is correct and no lights came on, you are done.

Dispose of old oil properly

Do not pour old oil down a drain or into the ground — it contaminates water and soil. Most auto parts stores accept used oil for free if you bought oil from them, and many municipal hazardous waste facilities accept it at no charge. Some quick-lube shops also accept oil from DIY changes. Call ahead to confirm what they accept and whether you need to bring it in a sealed container.

Keep the used oil in a sealed container until you can drop it off. Label the container clearly so anyone handling it knows what is inside. Many communities also offer curbside hazardous waste pickup on specific dates — check your local waste management website for schedules and rules.

Frequently Asked Questions

How often should I change my oil?

Check your owner's manual for the manufacturer's recommendation — it varies by engine type and oil grade. Older vehicles often needed changes every 3,000 miles, but modern engines with synthetic oil can go 7,500 to 10,000 miles or longer. Follow your manual, not a general rule.

Can I change my oil if the engine is cold?

Cold oil drains much more slowly and is harder to work with. Warm the engine for a few minutes first so the oil flows freely. Just make sure it cools enough that you can touch the drain plug without burning yourself — about five minutes after turning it off.

What if I spill oil on the driveway?

Soak it up when ready with cat litter, sand, or an absorbent cloth. Let it sit for 15 minutes, then sweep or wipe it up. Do not hose it down — oil runs into storm drains and waterways. Dispose of the soaked material as you would the used oil.

Do I need to replace the drain plug every time?

If your drain plug has a crush washer (a soft metal ring under the bolt head), replace it each time — a reused washer can leak. If the plug itself is damaged or stripped, replace the plug. Otherwise, the same plug can be reused for many oil changes.

What if the oil filter is stuck and won't unscrew?

Tap the filter wrench gently with a hammer to get a better grip, or wrap a rubber band around the filter for extra traction. If it is still stuck, try loosening it by hand with a rag for better grip. As a last resort, carefully puncture the filter with a screwdriver to break the seal, then unscrew it. Never force it so hard that you damage the mounting surface.