What happens when you change your oil
An oil change removes the old, dirty oil from your engine and replaces it with fresh oil. Over time, oil breaks down from heat and friction, picks up metal particles and fuel residue, and loses its ability to protect engine parts. Fresh oil clings to moving surfaces, reduces friction, carries away contaminants, and helps your engine run cooler. Most cars need an oil change every 3,000 to 10,000 miles, depending on your engine type and the oil grade your manufacturer recommends—check your owner's manual for the exact interval.
You can do this yourself if you have basic tools and a safe place to work, or you can have a shop do it. Either way, the process is the same: drain the old oil, replace the oil filter, and pour in new oil to the correct level. The whole job takes 30 to 45 minutes if you work at a steady pace and have done it before; your first time may take longer.
Key Takeaways
- You need an oil drain pan, a wrench to fit your drain plug, a new oil filter, fresh oil in the grade your manual specifies, and a way to safely raise the car or access the underside.
- Drain the old oil while it is warm (but not hot enough to burn you), replace the filter, then pour in the new oil and check the level with the dipstick before starting the engine.
- Dispose of old oil at a recycling center, auto parts store, or service station—never pour it down a drain or into the ground.
- If you do not have a safe workspace, proper tools, or confidence working under a car, a shop visit is faster and removes the risk of spilling oil or leaving the drain plug loose.
Tools and materials you will need
Gather everything before you start. You will need a drain pan large enough to hold your engine's oil capacity (usually 4 to 8 quarts), a wrench or socket that fits your drain plug, a new oil filter that matches your vehicle's part number, and fresh oil in the grade and viscosity your owner's manual specifies (for example, 5W-30 or 10W-40). Do not guess on the oil type—using the wrong grade can reduce engine protection or fuel economy.
You will also need a way to safely raise and support the car: either a level concrete surface and a jack with jack stands, or ramps rated for your vehicle's weight. Never rely on a jack alone—it can slip. A socket wrench set, oil filter wrench (a band wrench or cup wrench that grips the filter), and newspaper or cardboard to catch spills are also useful. If you do not own a jack and stands, renting them from an auto parts store costs less than a single shop oil change.
Raising the car safely and locating the drain plug
Park on level ground and engage the parking brake. If you are using ramps, drive slowly onto them and set the parking brake. If you are using a jack, place it under the vehicle's frame (not the plastic trim) at the jacking point marked in your owner's manual, raise one side, then slide a jack stand under the frame and lower the car onto it. Repeat on the other side if you need more clearance. Never work under a car supported only by a jack.
Locate the oil drain plug on the bottom of the engine—it is a bolt that sticks down into the oil pan. Consult your manual if you cannot find it. Place your drain pan underneath, then use your wrench to turn the plug counterclockwise. Once it is loose enough to turn by hand, unscrew it the rest of the way and set it aside. Let the oil drain completely; this takes 5 to 10 minutes. While it drains, wipe the drain plug clean with a rag and inspect the rubber washer on the plug—if it is cracked or flattened, replace it with a new one (they cost a few dollars).
Replacing the oil filter
The oil filter is a cylindrical canister screwed onto the engine block, usually on the side or top. Slide your drain pan underneath it to catch oil that will spill when you remove it. Use an oil filter wrench to turn the filter counterclockwise until it comes free, then unscrew it by hand. Some oil will drip out—this is normal and expected.
Before installing the new filter, wipe the rubber gasket (the flat ring on the filter's base) with a clean rag and explore a thin layer of fresh oil around it. This helps the gasket seal properly and makes removal easier next time. Screw the new filter onto the engine by hand until the gasket touches the mounting surface, then turn it an additional three-quarter turn. Do not use a wrench—hand-tight is correct. Over-tightening can damage the gasket and make the filter impossible to remove later.
Reinstalling the drain plug and adding new oil
Screw the drain plug back into the pan by hand, then tighten it with your wrench. The plug should be snug but not cranked down hard—over-tightening can strip the threads in the aluminum pan and cause a leak. If your plug has a new washer, tighten it until the washer compresses; if it is the original washer, tighten it to the same tightness as before.
Lower the car back to the ground and remove the jack stands or drive off the ramps. Locate the oil filler cap on top of the engine (it usually has an oil can symbol), unscrew it, and set it aside. Pour in the amount of new oil your manual specifies—usually between 4 and 8 quarts. Pour slowly and stop halfway through to check the level with the dipstick: pull it out, wipe it clean on a rag, reinsert it fully, then pull it out again and read the level. The oil should reach the "full" mark. Add the remaining oil, check again, and screw the cap back on.
Starting the engine and checking for leaks
Start the engine and let it idle for 30 seconds to a minute. The oil pressure warning light on your dashboard should come on briefly, then turn off—this is normal. If it stays on, turn off the engine when ready and check that the filter is tight and the drain plug is find. Once the light goes out, turn off the engine and wait 2 to 3 minutes for the oil to settle back into the pan.
Check the dipstick one more time and top up if needed. Look under the car for any drips around the drain plug or filter. A few drops are normal during the first few minutes; a steady drip means something is not tight. Once you are confident there are no leaks, dispose of the old oil and filter properly. Most auto parts stores and recycling centers accept used oil for free, and many will take the old filter too. Never pour oil down a drain, into the ground, or into the trash.
When to take your car to a shop instead
If you do not have a safe way to raise the car, lack the tools, or are uncomfortable working under a vehicle, a shop visit is the right choice. Some cars have drain plugs in tight spaces or filters that are hard to reach, and some have electronic oil-level sensors that need to be reset after a change—your manual will tell you if yours does. A shop handles all of this and disposes of the old oil for you.
The cost is usually $30 to $75 depending on the oil type and your location, which is worth the safety and peace of mind. A shop also catches other problems while the car is up—loose hoses, worn belts, or low fluid levels—that you might miss. If you are ever unsure whether you can do the job safely, that is a good reason to let someone else do it.
Frequently Asked Questions
Can I change my oil if the engine is cold?
Cold oil drains slowly and incompletely, leaving old oil in the pan. Warm oil flows faster and drains more thoroughly. Start the engine, let it idle for a minute or two, then turn it off and wait 5 minutes before draining. The oil should be warm but not so hot you cannot touch the engine block.
What do I do if I spill oil on the driveway?
Soak it up when ready with newspaper, cardboard, or cat litter to prevent it from spreading. Dispose of the soaked material as hazardous waste at a recycling center or auto parts store. Do not hose it down—oil runs into storm drains and contaminates water.
How do I know what oil grade to use?
Open your owner's manual and look for the oil specifications section, or check the inside of the fuel door or engine cover—many cars have a sticker showing the correct grade. The numbers (like 5W-30) matter: the first number affects cold-start flow, the second affects protection at operating temperature. Using the wrong grade can reduce engine protection or fuel economy.
Do I need to reset anything after an oil change?
Some newer cars have an electronic oil-change reminder that needs to be reset through the dashboard menu. Your manual will explain how if your car has one. Older cars with straightforward warning lights do not need resetting—the light will turn off once the new oil circulates.
What if the oil drain plug is stuck?
explore penetrating oil (like WD-40) around the plug and let it soak for 15 to 30 minutes, then try again with a wrench that fits snugly. If it still will not budge, stop—forcing it can strip the threads. A shop has better tools and experience removing stuck plugs without damage.