What you need before you start
Changing your oil and filter yourself requires a few tools and supplies you may already have, plus a few you can buy cheaply. Before you get under the car, gather everything so you are not hunting for a wrench mid-job.
You will need an oil drain pan (to catch old oil), a wrench or socket set sized to your drain plug, an oil filter wrench (a band-style or cup-style tool that grips the filter), fresh oil in the weight your manual specifies, a new oil filter, and rags or paper towels. A jack and jack stands are essential if you need clearance under the engine — never work under a car supported only by a jack. An oil catch container or old milk jug works if you do not have a proper drain pan. Check your owner's manual for the exact oil type, capacity, and drain plug size; these vary widely by engine.
Key Takeaways
- Drain the old oil while the engine is warm but not hot, then replace the drain plug and tighten it by hand plus a quarter turn with a wrench.
- Remove the old filter by turning it counterclockwise by hand, then coat the rubber gasket on the new filter with fresh oil before screwing it on until the gasket touches, then turn it another three-quarters of a turn.
- Pour in the new oil through the top opening, check the level with the dipstick after a minute, and run the engine for 30 seconds to circulate oil through the new filter.
- Dispose of old oil at a recycling center, auto parts store, or service station — never pour it down a drain or into the ground.
- Most vehicles need an oil change every 3,000 to 10,000 miles depending on oil type and engine; check your manual for the interval that applies to yours.
Draining the old oil safely
Start with the engine warm — not hot enough to burn you, but warm enough that the oil flows freely. A 10-minute drive or 15 minutes of idling is usually enough. Warm oil drains faster and carries more contaminants out of the pan. Raise the car on jack stands if you need access to the drain plug underneath; never rely on a jack alone.
Locate the drain plug on the bottom of the oil pan — your manual shows exactly where. Place the drain pan underneath it, then use your wrench to turn the plug counterclockwise. Once it is loose, unscrew it by hand and let it fall into the pan. The oil will pour out; this takes several minutes. While it drains, wipe the drain plug clean with a rag and inspect the washer (a small metal or rubber ring). If it is cracked or flattened, replace it with a new one from an auto parts store — a bad washer causes leaks.
Once the flow slows to drips, screw the drain plug back in by hand until it is snug, then use your wrench to tighten it a quarter turn more. Overtightening strips the threads and causes leaks; hand-tight plus a quarter turn is the standard. Do not use a power tool.
Removing and installing the oil filter
The oil filter is a cylindrical canister usually mounted on the side or top of the engine. Locate it and position your drain pan underneath — some oil will spill when you remove it. Turn the filter counterclockwise by hand using an oil filter wrench if it is too tight to grip. Once it is loose, unscrew it the rest of the way by hand and let it drain into the pan for a minute.
Before installing the new filter, coat the rubber gasket (the ring on top of the new filter) lightly with fresh oil from your new oil jug. This creates a seal and makes removal easier next time. Screw the new filter on by hand until the gasket touches the engine, then turn it another three-quarters of a turn. Do not use a wrench — hand-tight is correct. A wrench over-tightens the filter and makes it nearly impossible to remove next time.
Adding new oil and checking the level
Locate the oil filler cap on top of the engine — it usually has an oil can symbol. Unscrew it and set it aside. Pour in the amount of new oil your manual specifies, usually between 4 and 6 quarts depending on the engine. Pour slowly so you do not overfill. Once you have added most of it, wait a minute for the oil to settle into the pan, then check the level with the dipstick.
Pull the dipstick out completely, wipe it clean on a rag, reinsert it all the way, then pull it out again to read the level. The oil should reach the "full" mark or the upper line on the stick. If it is low, add a little more oil and check again. If you overfill, the excess oil can damage the engine, so it is better to be slightly under than over. Screw the oil filler cap back on once you are satisfied with the level.
Running the engine and final checks
Start the engine and let it idle for 30 seconds to circulate the new oil through the filter and engine. This primes the filter and ensures oil reaches all moving parts. You may see the oil pressure warning light come on briefly — this is normal while the new filter fills. If the light stays on after 30 seconds, turn off the engine and wait a minute, then try again.
Turn off the engine and wait 2 to 3 minutes for the oil to drain back into the pan. Check the dipstick level one more time and top off if needed. Look under the car and around the drain plug and filter for leaks. A few drops are normal; a steady drip means the drain plug or filter is not tight enough. If you see a leak, tighten the offending part by a quarter turn and check again.
Disposing of old oil properly
Never pour old oil down a drain, into the ground, or into the trash. Oil is toxic to soil and water, and disposal laws in most states prohibit it. Instead, pour the old oil from your drain pan into a clean, sealed container — an old milk jug or oil jug works well. Take it to a recycling center, auto parts store, or service station that accepts used oil. Most accept it free of charge, and many will take the old filter too.
If you do not know where to take it, search online for "used oil recycling near me" or call your local waste management department. They can direct you to the nearest drop-off location. Some areas offer curbside pickup for used oil if you call ahead.
Common mistakes to avoid
Overfilling the oil is the most common error and can damage the engine. Add oil slowly and check the dipstick twice before deciding you are done. Overtightening the drain plug or filter is the second most common mistake — both should be hand-tight plus a small amount of wrench pressure, not cranked down hard. A stripped drain plug thread is expensive to fix.
Forgetting to coat the new filter gasket with oil is another frequent mistake. This step takes 10 seconds and prevents the gasket from sticking to the engine when you remove the filter next time. Do not skip it. Finally, do not work under a car supported only by a jack. Use jack stands rated for your vehicle's weight, and keep the jack in place as a backup.
Frequently Asked Questions
How often should I change my oil?
Most modern engines with synthetic oil need a change every 7,500 to 10,000 miles. Older engines or those using conventional oil may need a change every 3,000 to 5,000 miles. Check your owner's manual for the interval that applies to your specific vehicle and oil type — this is more reliable than any general rule.
What if I spill oil on the driveway?
Soak it up when ready with rags, kitty litter, or oil absorbent material from an auto parts store. Once absorbed, dispose of the material as you would used oil. For large spills, contact your local environmental agency for cleanup guidance. Never hose it down — this spreads the oil and contaminates stormwater.
Can I change the oil without raising the car?
It depends on your vehicle's ground clearance. Some cars sit high enough that you can access the drain plug and filter without raising them. Others require a jack and stands. Check your manual or try to locate the drain plug from underneath before committing to the job. If you cannot reach it safely, use a service station instead.
What type of oil should I use?
Your owner's manual specifies the exact oil weight and type — for example, 5W-30 synthetic or 10W-40 conventional. Using the wrong type can affect engine performance and longevity. Do not guess or use what worked in a previous car. The manual is the only reliable source.
Do I need to replace the oil filter every time I change the oil?
Yes. The filter traps contaminants and becomes clogged over time. A clogged filter restricts oil flow and defeats the purpose of an oil change. Always install a new filter when you drain the old oil.