What happens when you change your own oil

Changing your oil means draining the old, dirty oil from your engine, replacing the oil filter, and filling the engine with fresh oil. You do this work underneath and around your engine, using basic hand tools and a way to safely lift the car or access the underside. The whole job takes 30 minutes to an hour once you have done it before, and longer the first time.

The reason to do it yourself is cost: a shop charges $40 to $100 for an oil change depending on your car and oil type, while you spend $20 to $50 on oil and a filter. The reason not to is risk—if you don't drain the old oil completely, don't install the filter correctly, or overfill the engine, you can damage the engine. You also need a safe way to get under the car, which means ramps or a jack and jack stands, not just jacking the car up and hoping.

Key Takeaways

  • You need the correct oil type and capacity for your car, found in your owner's manual or on a sticker under the hood, not on a shop receipt or guessed from another car.
  • The oil drain plug is at the lowest point of the engine and will be hot if the engine has run recently, so let the car cool for at least five minutes after driving.
  • The oil filter screws on by hand and should be tight enough that you cannot turn it with your fingers, but not so tight that you need a wrench to remove it next time.
  • Overfilling the engine with oil damages the engine just as much as running low, so check the level with the dipstick after filling and add only what the manual says.
  • Old oil is hazardous waste and cannot go in the trash or down a drain; most shops and recycling centers take it free or for a small fee.

Gather the right oil, filter, and tools before you start

Open your owner's manual and find the section on oil specifications. It will list the oil viscosity (the thickness rating, like 5W-30) and the total capacity in quarts or liters. Write this down. Do not guess based on what another car uses or what a shop told you last time—the wrong oil can reduce fuel economy, increase engine wear, or cause the engine to run too thick in cold weather.

Buy that exact oil type and quantity, plus one oil filter. The filter part number is also in your manual or on the old filter itself. You will also need an oil drain pan (a shallow metal or plastic tray to catch the old oil), an oil filter wrench (a socket-like tool that grips the filter), a wrench or socket set to remove the drain plug, and ramps or a jack with jack stands to safely lift the car. Do not work under a car supported only by a jack.

Lift the car safely and locate the drain plug

Park on level ground and engage the parking brake. If you are using ramps, drive slowly onto them until the front wheels are centered on both ramps. If you are using a jack, place it under the frame (not the plastic bumper or body panel) at the jacking point marked in your manual, raise the car, and slide jack stands under the frame on both sides. Lower the car onto the stands. Never work under a car supported only by a jack.

Look underneath the engine toward the lowest point. The oil drain plug is a bolt, usually between half an inch and one inch across, sticking down from the oil pan (the large metal reservoir at the bottom of the engine). It may have a rubber or plastic washer attached. Place your drain pan directly underneath it. If the engine has run in the last hour, the oil will be hot—touch the engine block first to check, and wait if it is too hot to hold your hand against for five seconds.

Drain the old oil and replace the filter

Using the correct wrench or socket, turn the drain plug counterclockwise to loosen it. Once it is loose enough to turn by hand, unscrew it the rest of the way by hand, letting it fall into the drain pan. The oil will flow out; this takes five to ten minutes. While you wait, locate the oil filter. It is a cylindrical canister, usually white or blue, screwed onto the side of the engine. Place the drain pan underneath it.

Use the oil filter wrench to turn the filter counterclockwise until it comes free. Unscrew it by hand the rest of the way. Oil will spill, so keep the pan under it. Wipe the rubber sealing ring (the flat gasket on the filter) off the engine block with a clean rag. Dip your finger in fresh oil and coat the rubber ring on the new filter lightly. Screw the new filter onto the engine by hand until the rubber ring touches the block, then turn it three-quarters of a turn more. Do not use the wrench to tighten it.

Wipe the drain plug clean with a rag and screw it back in by hand. Once it is snug, use the wrench to tighten it another quarter turn. Do not over-tighten; you will strip the threads and create a leak.

Fill the engine with new oil and check the level

Lower the car back to the ground. Open the hood and locate the oil filler cap on top of the engine—it usually has an oil can symbol on it. Unscrew it and set it aside. Place a funnel in the opening and pour in the amount of oil your manual specified, minus one quart. Let it settle for a minute.

Pull out the dipstick (a long thin rod with markings on it, usually with a yellow or orange handle), wipe it clean on a rag, reinsert it all the way, and pull it out again. The oil level should be between the minimum and maximum marks. If it is below minimum, add a little more oil and check again. If it is above maximum, you have overfilled the engine—do not start it. Instead, place the drain pan under the drain plug, loosen the plug slightly, and let a small amount of oil drain out until the level is correct.

Screw the oil filler cap back on. Start the engine and let it run for 30 seconds, then turn it off. Wait two minutes for the oil to settle, then check the level again with the dipstick. It should still be between the marks. If it has dropped, add a small amount more.

Dispose of old oil safely and record the service

Old motor oil is hazardous waste and cannot be thrown in the trash, poured down a drain, or left on the ground. Most auto parts stores that sell oil will take used oil free of charge. Some recycling centers and municipal hazardous waste facilities also accept it, sometimes for a small fee. Call ahead to confirm they accept oil and what their hours are. Bring the old oil in a sealed container—the drain pan works, or pour it into an old milk jug or oil bottle with a tight cap.

Write down the date, mileage, and oil type in your owner's manual or in a notes app on your phone. This record helps you remember when the next change is due and proves to a future buyer that you maintained the car. Most cars need an oil change every 5,000 to 7,500 miles or every six months, whichever comes first, though some newer cars can go 10,000 miles between changes. Check your manual for the interval that applies to your car.

Common mistakes that damage the engine

The most common mistake is overfilling. Even one quart too much can cause the crankshaft to whip the oil into foam, which cannot lubricate the engine properly and can cause bearing damage. Always check with the dipstick and fill to the mark, not to the top of the filler hole.

The second mistake is installing the filter too tight. If you use a wrench to tighten the filter, you will not be able to remove it by hand next time, and you may crack the filter housing. Tighten by hand only, and only three-quarters of a turn after the rubber ring touches the block.

The third mistake is not draining the old oil completely. If you remove the drain plug and walk away after a few minutes, you leave a quart or more of old oil in the pan. Let it drain for at least ten minutes, and longer if the oil is cold and thick. The fourth mistake is using the wrong oil type. Always check your manual, not a shop receipt or a guess. Using 10W-30 in an engine that calls for 5W-30 can reduce fuel economy and increase wear in cold weather.

Frequently Asked Questions

Do I need to warm up the engine before draining the oil?

A warm engine drains faster and more completely than a cold one, so a short drive or letting the engine idle for a few minutes helps. However, the oil will be very hot when ready after driving, so let the car cool for at least five minutes before you touch the drain plug. Warm oil is better than cold oil, but not so hot that you burn yourself.

What if I can't get the drain plug loose?

If the plug is stuck, explore penetrating oil (like WD-40) around the base and let it soak for 15 minutes. Use a wrench that fits snugly—a wrench that is too small will slip and round off the corners. If it still will not budge, stop and take the car to a shop rather than risk stripping the plug or the threads in the pan.

Can I change the oil without lifting the car?

Some cars with high ground clearance allow you to crawl underneath without lifting, but most do not. Ramps are the safest and cheapest option for a driveway job. Never work under a car supported only by a jack, even for a few minutes.

How do I know if the new filter is on tight enough?

After the rubber ring touches the engine block, turn the filter three-quarters of a turn more by hand. You should not be able to turn it any further without significant effort. If you can still turn it easily, it is not tight enough. If you need a wrench to turn it at all, it is too tight.

What should I do with the old drain plug?

Keep it. The plug is reusable unless it is damaged or the rubber washer is cracked. Wipe it clean and screw it back in. If the washer is damaged or the plug leaks, buy a new one—they cost a few dollars and are available at any auto parts store.