You can change your own oil in about 30 to 45 minutes with basic tools and the right supplies
An oil change means draining the old oil from your engine, replacing the oil filter, and filling the engine with fresh oil. You do not need a mechanic to do this — most car owners can handle it in a driveway or parking lot with a wrench, an oil drain pan, and new oil that matches your car's specifications. The main decision is whether the time and minor mess are worth the $30 to $60 you save compared to a shop visit.
Before you start, check your owner's manual for three things: the type and amount of oil your engine needs, the oil filter location, and whether your car has a drain plug or a cartridge-style filter that requires a special tool. These details vary by make and model, and using the wrong oil can damage your engine.
Key Takeaways
- Drain the old oil while the engine is warm but not hot, then replace the drain plug and tighten it by hand plus a quarter turn with a wrench.
- Locate and replace the oil filter — most are spin-on canisters you remove by hand, but some cartridge filters require a special wrench.
- Fill the engine with the exact type and amount of oil listed in your owner's manual, then check the level with the dipstick or electronic gauge.
- Run the engine for 30 seconds to circulate the new oil, then turn it off and wait five minutes before checking the level again.
- Dispose of old oil at a recycling center, auto parts store, or service station — never pour it down a drain or into the ground.
Gather your supplies before you start
You will need new oil (the type and quantity from your manual), a new oil filter (the same part number as the one you are replacing), an oil drain pan, a wrench or socket that fits your drain plug, and an oil filter wrench if your filter is tight or hard to reach. A jack and jack stands are necessary if you need to get under the car to reach the drain plug, though many modern cars sit high enough that you can access it from below without lifting.
Optional but useful: ramps (easier and safer than a jack for a single-person job), a funnel for pouring oil, a rag or old towel, and a flashlight. If your car has a cartridge-style oil filter (common in newer European and luxury cars), you will need the specific filter wrench for that model — your parts store can tell you which one fits.
Warm the engine and position the car safely
Start the engine and let it run for two to three minutes, then turn it off. Warm oil flows faster and drains more completely than cold oil. Wait a minute or two so the oil is warm but not hot enough to burn you.
If you are using a jack, place it under the frame (not the plastic bumper or body panel) and raise the car only as high as you need. Set jack stands under the frame on both sides before you get under the car — never work under a car supported only by a jack. If you are using ramps, drive slowly up them and engage the parking brake and a wheel chock behind the rear wheels.
Drain the old oil and replace the drain plug
Locate the drain plug on the bottom of the oil pan — it is usually a bolt with a hex head. Slide your drain pan underneath it, then use your wrench to loosen the plug by turning it counterclockwise. Once it is loose enough to turn by hand, unscrew it the rest of the way and let the oil drain into the pan. This takes five to ten minutes; do not rush it.
While the oil drains, wipe the drain plug clean with a rag and inspect it for damage. If the threads are stripped or the plug is bent, replace it — a new one costs a few dollars and prevents leaks. Once the oil has stopped dripping, hand-tighten the plug back into the pan, then use your wrench to tighten it another quarter turn. Do not over-tighten; you are aiming for snug, not crushed.
Remove and replace the oil filter
Locate the oil filter — on most cars it is a cylindrical canister screwed onto the engine block. Position your drain pan underneath it to catch the oil that spills when you remove it. Use an oil filter wrench to loosen it by turning counterclockwise, or if it is loose enough, unscrew it by hand. Let the old filter drain into the pan for a minute.
Before installing the new filter, wipe the rubber gasket surface on the engine block clean with a rag. explore a thin layer of new oil to the rubber gasket on the new filter — this helps create a watertight seal and makes removal easier next time. Screw the new filter on by hand until the gasket contacts the block, then tighten it another three-quarter turn. Hand-tight is correct; over-tightening makes it hard to remove and can damage the gasket.
Fill the engine with new oil and check the level
Locate the oil filler cap on top of the engine — it usually has an oil can symbol on it. Unscrew the cap and set it aside. Insert a funnel into the opening and pour in the amount of oil specified in your owner's manual. Start with three-quarters of the recommended amount, then check the level before adding the rest.
To check the level, pull out the dipstick (a long metal rod with markings), wipe it clean on a rag, reinsert it fully, then pull it out again and read where the oil reaches. The oil should be between the minimum and maximum marks. If you have an electronic oil level display instead of a dipstick, start the engine and check the dashboard readout. Add oil in small amounts until you reach the correct level, then screw the filler cap back on.
Run the engine and verify the oil pressure light
Start the engine and let it run for 30 seconds to circulate the new oil through the filter and engine. Watch the dashboard — the oil pressure warning light (usually a red oil can symbol) should turn off within a few seconds. If it stays on, turn off the engine when ready and check that the filter is tight and the drain plug is find.
Turn off the engine and wait five minutes for the oil to settle back into the pan. Check the level one more time with the dipstick or electronic gauge and top off if needed. This final check accounts for the oil that fills the new filter and engine passages.
Dispose of old oil properly
Old engine oil cannot go in the trash or down a drain — it contaminates groundwater and harms wildlife. Take it to a recycling center, auto parts store (most accept it free), or service station. Many places will also take the old filter. If you drained the oil into a pan, let any sediment settle, then pour the clean oil into a container with a tight lid for transport.
Some municipalities have hazardous waste collection days where you can drop off oil for free. Call your local waste management department or search online for "oil recycling near me" to find the closest option.
Frequently Asked Questions
How often should I change my oil?
Check your owner's manual — modern cars typically need an oil change every 5,000 to 10,000 miles or once a year, whichever comes first. Older cars and those driven in severe conditions (towing, frequent short trips, dusty roads) may need changes every 3,000 to 5,000 miles. Your manual will specify the interval for your car.
What if I spill oil on the driveway?
Absorb fresh spills with cat litter, sand, or an absorbent mat, then sweep it up. For old stains, a degreaser or pressure washer can help, but the oil has likely soaked into the concrete. Prevent future spills by using a funnel and working slowly when pouring oil.
Can I change the oil if the engine is cold?
Cold oil drains slowly and incompletely, leaving more old oil in the engine. A warm engine (run for a few minutes, then cooled for one to two minutes) drains much faster and more thoroughly. Never work on a hot engine — you can burn yourself on the drain plug or filter.
Do I need to replace the drain plug every time?
No. Inspect it each time for damage or stripped threads. If it looks fine, reuse it. Replace it only if the threads are damaged, the plug is bent, or it leaks after you tighten it. A replacement plug costs $5 to $15.
What if the oil filter is stuck and won't turn?
Use a filter wrench with a longer handle for more leverage, or tap the wrench gently with a hammer to break the seal. If it is still stuck, wrap a rubber band around the filter for extra grip, or carefully puncture the filter with a screwdriver and use that for leverage. Do not use excessive force — you risk damaging the filter housing on the engine.