Check your oil with the engine off, on level ground, using the dipstick
Checking your oil takes about two minutes and tells you whether you have enough to keep your engine safe until your next oil change. You pull out a long metal rod called a dipstick, wipe it clean, reinsert it fully, then pull it out again and read where the oil level sits against the markings. The oil should reach the "full" line or fall between the "full" and "low" marks. If it's below the low mark, you add oil before driving.
The reason this matters: oil circulates through your engine to lubricate moving parts, cool them, and carry away debris. Without enough oil, metal parts grind together, heat builds up, and your engine can seize or fail. A seized engine cannot be repaired—it must be replaced, which costs thousands of dollars. Checking oil every month or before a long drive catches a slow leak or burn-off before it becomes a crisis.
Key Takeaways
- Always check oil when the engine is cold and the car sits on level ground, because hot oil gives a false high reading and an uneven surface skews the dipstick.
- Pull the dipstick all the way out, wipe it on a clean rag or paper towel, reinsert it fully until it seats, then pull it out again to read the true level.
- Oil between the low and full marks is normal; below the low mark means you need to add oil before your next drive.
- If you add oil and the level drops again within a few weeks, your car has a leak or is burning oil, and you should have it inspected.
Locate the dipstick under your hood
Open your hood and look for a long rod with a yellow, orange, or red handle. The handle is usually plastic and stands out against the engine. On most cars, the dipstick sits on the driver's side of the engine, near the front or middle. Your owner's manual shows the exact location if you cannot spot it.
If your car is a newer model—roughly 2010 or later—it may not have a traditional dipstick. Some manufacturers replaced it with an electronic oil-level sensor that displays the reading on your dashboard. Check your manual to confirm. If you have no dipstick and no dashboard display, contact your dealership or a mechanic to learn how to check your specific model.
Pull the dipstick and wipe it clean
Grasp the handle firmly and pull the dipstick straight out. Oil will coat the rod. Take a clean rag, paper towel, or old cloth and wipe the oil off completely. You need to see the bare metal or markings underneath. Wipe from the base toward the tip so you remove all the oil residue.
Do not use a rag that is wet or damp—moisture on the dipstick will mix with the oil and give you a false reading. A dry cloth or paper towel works best. If you do not have one handy, use the inside of your shirt or a dry leaf, but avoid anything that will leave lint or debris on the rod.
Reinsert the dipstick fully and remove it again
Push the clean dipstick back into its tube. Push it all the way down until it seats at the bottom—you will feel slight resistance when it is fully inserted. Do not force it, but do not stop short either. A dipstick that is not fully seated will give a false high reading because the tip is not in the oil.
Wait a few seconds, then pull it straight out again. This second pull is the one you read. The oil will have coated the rod again, and this time the level is accurate because the dipstick was fully inserted.
Read the oil level against the markings
Look at the rod and find the two marks or lines near the tip. One is labeled "full" or "max," and the other is labeled "low" or "min." The oil will have coated the rod up to a certain height. If the oil reaches the full line, your level is correct. If it sits between the full and low marks, you are still within the safe range. If the oil is below the low mark, you need to add oil.
Some dipsticks use a crosshatched or textured zone instead of two distinct lines. The oil should reach into or above this zone. If the rod is dry above the zone, your oil is low. Check your owner's manual if you are unsure how to read your specific dipstick.
Add oil if the level is below the low mark
If the oil is low, you will need to add the correct type and amount. Your owner's manual specifies the oil grade—usually something like 5W-30 or 10W-40. Buy a quart of that grade from any auto parts store or gas station. Do not mix grades or use the wrong viscosity, because it can affect engine performance and protection.
Locate the oil filler cap on top of your engine. It usually has an oil can symbol printed on it. Twist it counterclockwise to remove it. Pour the quart slowly into the opening. Wait a minute for the oil to settle, then check the dipstick again using the same process: wipe, reinsert fully, remove, and read. Add more oil in half-quart increments if needed until the level reaches the full mark. Replace the filler cap when you are done.
Check oil when the engine is cold and on level ground
Always check oil at least five minutes after the engine has been off, or better yet, in the morning before you drive. Hot oil expands and coats the dipstick higher than the true level, giving you a false reading. If you check when ready after driving, you may think you have more oil than you actually do, and you could miss a real shortage.
Park on flat, level ground before checking. A car parked on a slope or incline will tilt, and the oil will pool to one side of the pan, making the dipstick read inaccurately. A driveway or parking lot is fine; a steep hill is not. Level ground ensures the oil settles evenly and the dipstick reads true.
Frequently Asked Questions
How often should I check my oil?
Check it once a month or before a long drive. If you notice the level dropping between oil changes, check it more often to catch a leak or excessive burn-off early. Some newer cars with synthetic oil can go longer between checks, but monthly is a safe habit for most vehicles.
What does it mean if oil keeps dropping even after I add it?
A slow drop over weeks is normal—engines burn a small amount of oil during operation. A rapid drop or puddles under your car point to a leak. Either way, have a mechanic inspect the engine to rule out a crack, loose drain plug, or worn seals. Driving on low oil risks engine damage.
Can I check oil while the engine is warm?
You can, but the reading will be higher than the true level because warm oil expands. If you must check a warm engine, add a little extra caution to your reading and plan to recheck when it cools. Cold checks are always more reliable.
What if I cannot find the dipstick?
Check your owner's manual for the exact location—it varies by make and model. If your car has no dipstick, it likely has an electronic sensor that displays oil level on the dashboard or infotainment screen. Consult your manual or a dealership to learn how to read it.
Is it okay to drive if my oil is slightly below the low mark?
Not for long. Driving on low oil increases friction and heat in the engine. Add oil before your next drive, even if it is just a quart. Repeated driving on low oil accelerates wear and can lead to engine failure.