What you need before you start
An oil change takes 30 minutes to an hour if you have the right tools and know where things are under your hood. You will need an oil drain pan (to catch the old oil), a wrench or socket set that fits your drain plug, an oil filter wrench, fresh oil in the weight your car needs, a new oil filter, and jack stands if you are working under the car. A creeper (a low wheeled board) makes lying under the vehicle easier but is not required.
Before you buy anything, check your owner's manual or look up your vehicle on a parts retailer's website to find out what oil weight your car takes — this is usually something like 5W-30 or 10W-40 — and how many quarts you need. The manual also tells you where the drain plug and filter are located, which varies by engine. Some cars have the filter on top where you can reach it standing up; others hide it underneath.
If you do not have a safe way to lift the car or get under it, or if you are not comfortable working with tools, a shop can do this job for $30 to $75 in labor alone. That is worth considering before you commit to doing it yourself.
Key Takeaways
- Drain the old oil while the engine is warm but not hot, then replace the drain plug and tighten it by hand plus a quarter turn with a wrench.
- Remove the old filter by turning it counterclockwise by hand, then coat the rubber gasket on the new filter with a thin layer of fresh oil before screwing it on until it just touches the engine block.
- Pour in the amount of new oil your manual specifies, then wait a minute and check the dipstick to confirm the level is in the safe range.
- Start the engine, let it run for 30 seconds, turn it off, wait a minute, and check the dipstick again to make sure the level has not dropped.
- Dispose of old oil at a recycling center, auto parts store, or quick-lube shop — never pour it down a drain or into the ground.
Step 1: Warm the engine and drain the old oil
Start the engine and let it idle for two or three minutes so the oil warms up. Warm oil flows faster and drains more completely than cold oil. Then turn the engine off and wait five minutes — you want the oil warm enough to flow but cool enough that you will not burn yourself.
Locate the drain plug underneath the engine (consult your manual if you cannot find it). Position your drain pan directly under it, then use a wrench to turn the plug counterclockwise. Once it is loose enough, unscrew it the rest of the way by hand, being careful because a little hot oil may still drip out. Let the old oil drain completely — this usually takes five to ten minutes. While you wait, you can locate the oil filter and prepare to remove it.
Step 2: Replace the drain plug
Once the oil has stopped dripping, wipe the drain plug clean with a rag and screw it back in by hand. Tighten it with a wrench — turn it about a quarter turn past hand-tight. Do not over-tighten; you are just sealing it, not crushing it. If you strip the threads by turning too hard, the plug will leak and you will have a bigger problem.
Some drain plugs have a rubber or metal washer that gets crushed each time you remove the plug. If your plug has one, replace it with a new washer when you reinstall the plug. Your parts store can sell you a replacement washer for a few cents if you need one.
Step 3: Remove and replace the oil filter
Locate the oil filter — it is a cylindrical canister about the size of a soda can, usually mounted on the side of the engine. Use an oil filter wrench to turn it counterclockwise until it comes free, then unscrew it the rest of the way by hand. Some oil will spill, so keep your drain pan underneath. Empty the old filter into the pan if it is not already empty.
Take the new filter and coat the rubber gasket (the ring at the top) with a thin layer of fresh oil from your new oil jug. This helps the gasket seal properly. Screw the new filter on by hand until the gasket touches the engine block, then turn it another three-quarters of a turn. You should be able to tighten it with your hand alone — if you need a wrench, you have turned it too far.
Step 4: Add new oil and check the level
Locate the oil filler cap on top of the engine — it usually has an oil can symbol on it. Unscrew it and set it aside. Pour in the amount of new oil your manual specifies, usually between four and six quarts depending on the engine. Pour slowly so you do not splash oil around the engine bay.
Wait about a minute for the new oil to settle, then pull out the dipstick (a long thin rod with markings on it), wipe it clean on a rag, reinsert it all the way, and pull it out again. The oil should reach the "full" mark or fall between the minimum and maximum marks. If it is low, add a little more and check again. If it is overfull, you will need to drain some out — do not run the engine with too much oil.
Step 5: Start the engine and recheck
Screw the oil filler cap back on, then start the engine and let it run for about 30 seconds. This circulates the new oil through the engine and fills the new filter. Turn the engine off and wait a minute for the oil to settle again, then check the dipstick one more time. The level should still be at or near the full mark. If it has dropped noticeably, add a small amount more.
Look under the car and around the drain plug and filter to make sure neither is leaking. If you see drips, turn off the engine and tighten the plug or filter slightly. Once everything looks dry, you are done.
Disposing of old oil safely
Never pour old oil down a drain, into the ground, or into a storm sewer. Oil is toxic and persists in the environment. Instead, pour it into a clean container with a tight lid and take it to a recycling center, an auto parts store (most accept it free), or a quick-lube shop. Many shops will take old oil even if you did not have them do the work.
The old oil filter can usually go in the regular trash, but some recycling centers prefer you to bring it with the oil. Call ahead if you are unsure.
Frequently Asked Questions
How often should I change my oil?
Check your owner's manual — newer cars often go 7,500 to 10,000 miles between changes, while older cars may need a change every 3,000 to 5,000 miles. Some manufacturers recommend synthetic oil, which lasts longer than conventional oil. Your manual will tell you which type your car needs.
What if I spill oil on the driveway?
Soak it up with cat litter, sand, or old rags as soon as possible. Let it sit for a few hours, then sweep it up and dispose of it as hazardous waste. Do not hose it down — that spreads it and sends it into storm drains. For large spills, contact your local environmental agency for guidance.
Can I change the oil if the engine is completely cold?
You can, but warm oil drains faster and more completely. If you must work on a cold engine, just expect the process to take longer and more oil to remain in the pan at the bottom of the engine.
Do I need to change the oil filter every time I change the oil?
Yes. The filter traps dirt and debris, and a clogged filter reduces oil flow. Replacing it at every oil change is standard practice and costs only $8 to $15.
What should I do with the old drain plug if I replaced the washer?
Keep the old plug in case you need it later, or recycle it as scrap metal. Do not throw it in the trash — metal should go to a recycling center.