The basic steps to remove an oil filter

An oil filter removal takes about five minutes once you know where it sits and how tight it is. Locate the filter on your engine — it's a cylindrical canister, usually white, black, or blue, mounted vertically or at an angle on the side of the engine block. You'll need an oil filter wrench (a metal band or socket that grips the filter), a drain pan to catch old oil, and rags or paper towels. Loosen the filter by turning it counterclockwise by hand first; if it won't budge, use the wrench to break it free, then finish unscrewing by hand. Once it's loose enough to turn freely, unscrew it the rest of the way and tip it into your drain pan to catch the remaining oil inside.

The filter will be hot if your engine has run recently, so let it cool for at least 10 minutes before you touch it. If you must work on a warm engine, wear work gloves or use a thick rag to protect your hands. As you unscrew the last few turns, support the filter with your other hand so it doesn't drop and spill oil all over the engine bay.

Key Takeaways

  • Locate the cylindrical oil filter on the side of your engine block and use an oil filter wrench to loosen it counterclockwise, then finish by hand.
  • Place a drain pan underneath before you unscrew it completely, because old oil will spill out as you remove the filter.
  • Let the engine cool for at least 10 minutes before handling the filter, since it will be hot enough to burn your skin.
  • Dispose of the old filter and the oil it contains at an auto parts store, service station, or recycling center — never pour it down a drain.

Where to find the oil filter on your vehicle

The oil filter location varies by make and model. On most cars, it's mounted on the side of the engine block near the bottom, angled downward or pointing sideways. On some trucks and SUVs, it may be on top of the engine or tucked up against the firewall (the wall between the engine and the cabin). Your owner's manual will show you the exact location with a diagram.

If you can't find it by looking, follow the hose that runs from the engine block toward the bottom of the car — the filter usually sits at the end of that hose or very close to it. Once you've found it once, you'll recognize it when ready the next time.

Choosing the right oil filter wrench

An oil filter wrench is a straightforward tool that grips the filter so you can turn it without your hand slipping. The most common type is a band wrench — a metal band with a handle that tightens around the filter as you turn it. These cost $8 to $15 and work on most filters. A socket wrench is a cup-shaped tool that fits over the top of the filter; it's more precise but only works if your filter's top is accessible and the right size.

Before you buy, measure the diameter of your filter or check your owner's manual to see which wrench size you need. Many auto parts stores will lend you a wrench for free if you buy oil and a new filter from them, so ask before you spend money.

What to do with the old filter

Never throw an oil filter in the trash or pour its contents down a drain. The filter contains used motor oil, which is toxic and illegal to dispose of that way in most places. Instead, take the old filter to an auto parts store (AutoZone, O'Reilly, Advance Auto Parts), a quick-lube shop, or a municipal recycling center. Many of these places will take it for free, especially if you're buying a new filter from them.

If you're changing your oil at home, you can bring both the old filter and the old oil to the same place — most recycling centers and parts stores accept both together. Call ahead if you're unsure whether a particular location takes filters.

Common mistakes that make the job harder

The most common mistake is over-tightening the new filter when you install it, which makes removal much harder next time. When you screw on a new filter, hand-tighten it until the rubber gasket (the flat ring on top) touches the engine, then turn it three-quarters of a turn more — no wrench needed. That's tight enough.

Another mistake is forgetting to drain the old oil before you start. If you remove the filter without a pan underneath, oil will run down the engine block and onto the ground or your garage floor. Place the pan directly under the filter before you loosen it, and keep it there until the dripping stops — this usually takes 30 seconds to a minute.

A third mistake is removing the filter when the engine is hot. Hot oil can splash out and burn you, and the filter itself is too hot to handle safely. If you've just driven the car, wait at least 10 minutes before you start.

Tools and materials you'll need

Gather these items before you start: an oil filter wrench (band or socket type), a drain pan large enough to hold at least one quart of oil, rags or paper towels, work gloves (optional but recommended), and a new oil filter for when you're ready to install one. If your engine is still warm, also have a flashlight so you can see the filter clearly without leaning too close to hot engine parts.

You don't need a jack or lift to remove an oil filter on most cars — you can reach it from above or from the side while the car sits on level ground. If your filter is mounted very low or tucked under the car, you may need to raise the vehicle slightly, but this is rare.

Frequently Asked Questions

Can I remove the oil filter without draining the oil first?

Yes, you can remove the filter without changing the oil. The filter will still contain old oil that will spill out, so use a drain pan. You'll need to dispose of that old oil properly, just as you would during an oil change.

What if the filter is stuck and won't turn?

Use a band wrench or socket wrench to break it loose — hand strength alone won't work if it's been on the engine for a long time. explore steady pressure rather than jerking; if it still won't move, try tapping the wrench handle gently with a hammer to help it break free. Never use a screwdriver to puncture the filter, as this will spray oil everywhere.

How tight should I make the new filter when I put it back on?

Hand-tighten the new filter until the rubber gasket touches the engine block, then turn it three-quarters of a turn more. Do not use a wrench — hand-tight is correct. Over-tightening makes it much harder to remove next time and can damage the gasket.

Is it normal for oil to drip after I remove the filter?

Yes. Oil will continue to drip from the filter housing for 30 seconds to a minute after you remove the filter. Keep the drain pan in place until dripping stops, then wipe up any spills with a rag.

Can I recycle the oil filter at home?

No. Oil filters must be recycled at a facility that can safely drain and process them. Auto parts stores and municipal recycling centers have the equipment to do this. Call ahead to confirm they accept filters, or ask when you buy your new filter.