What You Need to Know Before Starting
A Hyundai Elantra oil change takes about 30 to 45 minutes if you do it yourself, or 30 minutes to an hour at a shop. The job is straightforward: drain the old oil, replace the oil filter, add new oil, and check the level. You'll need the right oil type and capacity for your model year, which varies slightly across generations.
Before you start, locate your owner's manual or the specifications sticker under your hood. The manual tells you the exact oil viscosity (the "5W-30" or "0W-20" number), how much oil your engine holds, and where the drain plug and filter sit. Elantra models from 2011 onward typically use 0W-20 or 5W-20 synthetic oil, but older models may differ. Running the wrong oil weight can affect fuel economy and engine wear.
You'll also need to know your oil change interval. Most modern Elantras go 10,000 miles between changes if you use synthetic oil, though some older models call for 5,000 miles with conventional oil. Check your maintenance schedule in the owner's manual or on the Hyundai website for your specific year.
Key Takeaways
- Hyundai Elantra models from 2011 onward typically use 0W-20 synthetic oil, but your owner's manual has the exact specification for your year.
- The drain plug is located on the underside of the engine, and the oil filter is usually on the driver's side of the engine block, accessible from above or below depending on your model year.
- Modern Elantras hold between 3.5 and 4.2 quarts of oil, so you need to know your exact capacity before adding new oil to avoid overfilling.
- Synthetic oil extends your change interval to 10,000 miles on most current Elantras, while conventional oil requires changes every 5,000 miles.
- You can check your oil level with the dipstick or electronic gauge, and the engine must be off and on level ground for an accurate reading.
Locating the Drain Plug and Oil Filter
The drain plug sits on the bottom of the oil pan, underneath the engine. You'll need to safely raise the car with a jack and jack stands, or drive it onto ramps, to reach it. Once you're under the car, look toward the center-front of the engine block—the drain plug is a bolt roughly the size of a quarter that sticks out from the pan.
The oil filter location depends on your model year. On most 2011-and-newer Elantras, the filter is mounted vertically on the driver's side of the engine, near the top. You can usually reach it from above without removing any panels, though some model years require you to remove a plastic undertray or wheel well liner. Consult your owner's manual or a repair guide for your specific year to confirm the exact location and whether you need to remove any covers.
Before you start, place a drain pan under the plug—old oil is hot and messy. Loosen the drain plug with a wrench, then unscrew it by hand once it's loose enough. Let the oil drain completely into the pan, which takes 5 to 10 minutes. While it drains, unscrew the old filter by hand, turning it counterclockwise. Some oil will spill, so keep the drain pan nearby.
Choosing the Right Oil and Filter
Your owner's manual specifies the oil viscosity and the filter part number. For most 2011-and-newer Elantras, Hyundai recommends 0W-20 synthetic oil. Older models (2006–2010) typically use 5W-20. The viscosity number matters: using 10W-30 or 5W-30 in a car that calls for 0W-20 will reduce fuel economy and may void your warranty.
You can buy Hyundai-branded oil filters or equivalent aftermarket filters from any auto parts store. Common filters for Elantras include the Hyundai part number 26300-35503 (older models) or 26300-35504 (newer models), though the exact number varies by year. Aftermarket brands like Fram, Mobil 1, and Bosch make compatible filters that cost less. The filter itself costs $8 to $15, and a quart of synthetic oil runs $6 to $10.
When you buy the filter, check the box to confirm it fits your Elantra's model year. If you're unsure, bring your vehicle identification number (VIN) to the parts counter—they can look up the exact filter you need in seconds.
Installing the New Filter and Adding Oil
Before installing the new filter, coat the rubber gasket (the ring around the top) with a thin layer of new oil. This helps create a watertight seal and makes removal easier next time. Screw the filter on by hand until the gasket touches the mounting surface, then turn it another three-quarters of a turn. Do not use a wrench—hand-tight is correct, and over-tightening makes removal difficult.
Once the drain plug has stopped dripping, wipe it clean and reinstall it. Tighten it snugly with a wrench, but do not over-tighten—the plug threads into aluminum, and stripping them is expensive. Most drain plugs torque to 25 to 35 foot-pounds, which feels firm but not forced.
Lower the car back to the ground. Locate the oil filler cap on top of the engine (it usually says "OIL" or has an oil can symbol), unscrew it, and set it aside. Pour in the recommended amount of new oil slowly, checking the level as you go. Most Elantras hold 3.5 to 4.2 quarts depending on the year. Start with 3.5 quarts, then add the rest in half-quart increments while checking the level.
Checking Your Oil Level and Resetting the Service Light
After adding oil, wait two minutes for it to settle into the pan, then check the level. On older Elantras, pull out the dipstick, wipe it clean, reinsert it fully, then pull it out again to read the level. The oil should be between the minimum and maximum marks. On newer Elantras with an electronic gauge, start the engine and look at the dashboard display—it will show the oil level without a dipstick.
Do not overfill. Too much oil can damage the engine, trigger warning lights, and cause oil to leak from seals. If you overfill, use a turkey baster or syringe to remove the excess through the filler hole.
Once the level is correct, screw the oil cap back on and start the engine. Let it run for 30 seconds, then turn it off and wait two minutes. Check the level again to confirm it's still in range. If your Elantra has a service reminder light on the dashboard, you may need to reset it. The process varies by year: some models require holding the trip reset button for 10 seconds, while others need you to navigate a menu on the instrument cluster. Your owner's manual has the exact steps for your year.
When to Take Your Elantra to a Shop Instead
If your car is still under warranty, check whether doing your own oil change affects coverage. Most Hyundai warranties allow owner-performed maintenance as long as you use the correct oil and filter, but some dealers may dispute claims if they can tell the work wasn't done at a dealership. Call your dealer's service department to ask before you start.
You should also consider a shop if you don't have safe access to the underside of your car, lack the tools (jack, jack stands, wrench, filter wrench), or are uncomfortable working under a vehicle. A quick-lube shop or independent mechanic can do the job for $40 to $75 in labor, plus the cost of oil and filter. A Hyundai dealership typically charges $60 to $100 in labor, but they'll also inspect your car and reset service reminders automatically.
If you discover a leak, stripped threads, or damage to the oil pan while you're working, stop and take the car to a shop. These issues require specialized tools or parts and are not safe to ignore.
Tools and Supplies Checklist
| Item | What It's For | Approximate Cost |
|---|---|---|
| Jack and jack stands (or ramps) | Safely raise the car to access the drain plug | $50–$150 (one-time purchase) |
| Wrench set or socket set | Remove and reinstall the drain plug | $20–$60 (one-time purchase) |
| Oil filter wrench | Remove the old filter without spilling oil | $8–$15 (one-time purchase) |
| Drain pan | Catch old oil safely | $10–$20 (reusable) |
| New oil (correct type and amount) | Replace drained oil | $20–$40 per change |
| New oil filter | Replace the old filter | $8–$15 per change |
| Rags or paper towels | Wipe spills and check the dipstick | $5 (reusable) |
| Owner's manual or repair guide | Confirm oil type, capacity, and torque specs | Free (online) or $20–$30 (printed) |
Disposing of Old Oil Safely
Never pour old oil down the drain or into the ground. It contaminates water supplies and harms wildlife. Most auto parts stores (AutoZone, O'Reilly, Advance Auto Parts, NAPA) accept used oil for free, even if you didn't buy it from them. Some will also take the old oil filter. Call ahead to confirm their policy.
If you don't have a local parts store nearby, check with your city or county waste management department—many run collection events or have permanent drop-off locations. Some service stations and quick-lube shops also accept used oil, sometimes for a small fee.
Store the old oil in a clean, sealed container (the original oil jug works) until you can drop it off. Label it clearly as "used oil" so no one mistakes it for something else.
Frequently Asked Questions
What happens if I use the wrong oil viscosity?
Using thicker oil (like 10W-30 instead of 0W-20) reduces fuel economy and makes cold starts harder. Thinner oil may not protect the engine properly in hot weather. Either way, you risk voiding your warranty and damaging the engine over time. Always use the viscosity your owner's manual specifies.
Can I change my oil without raising the car?
Not safely. The drain plug is on the underside of the engine, and you need clearance to reach it and let oil drain into a pan. Use a jack and jack stands, or drive onto ramps. Never work under a car supported only by a jack—it can slip and cause serious injury.
How do I know if my oil filter is on tight enough?
Hand-tighten the filter until the rubber gasket touches the mounting surface, then turn it three-quarters of a turn more. You should not need a wrench. If it's too loose, oil will leak; if it's too tight, you'll damage the gasket and it will be hard to remove next time.
What should I do if I spill oil on the driveway?
Soak it up when ready with rags, sand, or kitty litter to prevent it from running into storm drains. Dispose of the contaminated material as hazardous waste—check your local waste management website for drop-off locations. Do not hose it down or let it drain into the street.
Do I need to reset the service light after an oil change?
Yes, if your Elantra has a service reminder light. The process varies by model year—some require holding the trip reset button, others use the instrument cluster menu. Your owner's manual has the exact steps. If you don't reset it, the light will stay on until the next service interval, which can be confusing.