Mopar oil filters are the factory-standard filters made by Chrysler for its vehicles
Mopar is Chrysler's parts division, and Mopar oil filters are engineered to meet the exact specifications of Chrysler, Dodge, Jeep, and Ram vehicles. When you buy a Mopar filter, you're getting a part designed by the same company that built your engine — it fits the mounting, handles the flow rate your engine needs, and meets the pressure tolerances Chrysler set during design.
You don't have to use a Mopar filter. Many aftermarket filters from other manufacturers work in Chrysler vehicles and cost less. But if you want the part Chrysler engineers chose for your specific model, Mopar is where to find it. The choice comes down to whether you prioritize factory-matched parts or lower cost.
Key Takeaways
- Mopar filters are made by Chrysler and designed specifically for Chrysler, Dodge, Jeep, and Ram vehicles, so they match your engine's exact specifications.
- You can find the correct Mopar filter number by looking at your owner's manual, checking your vehicle's build sheet, or asking a Chrysler dealer for your year, make, model, and engine size.
- Mopar filters typically cost more than aftermarket brands but less than dealer labor if you install them yourself.
- Aftermarket filters from established brands work in Chrysler vehicles and often cost significantly less, though they are not engineered by Chrysler.
How to find the right Mopar filter for your vehicle
The correct filter depends on your engine size and model year. Your owner's manual lists the Mopar part number in the maintenance section — usually near the oil capacity and viscosity grade. If you don't have the manual, you can call a Chrysler dealer with your vehicle identification number (VIN), year, make, and model, and they will tell you the exact part number.
You can also search online parts catalogs using your VIN. Websites like Mopar.com, RockAuto, and Amazon allow you to enter your VIN and see the correct filter. Write down the part number before you buy, because Mopar filters are labeled by number, not just by vehicle type — using the wrong number can mean a filter that doesn't fit or flows at the wrong rate.
Mopar filters versus aftermarket alternatives
Aftermarket filters from brands like Fram, Motorcraft, Bosch, and Wix are engineered to work in Chrysler vehicles and meet industry standards for flow and pressure. Many people use them without problems. The main differences are that Mopar filters are designed by Chrysler specifically for Chrysler engines, while aftermarket filters are designed to fit a wide range of vehicles.
In practice, this means Mopar filters may have slightly better fit and flow characteristics for your exact engine, but the difference is usually small. Aftermarket filters cost less — often 30 to 50 percent less — and are widely available at auto parts stores. If you change your oil on schedule, either type will protect your engine. The choice is whether you want the factory-engineered part or the cost savings of an aftermarket option.
Where to buy Mopar oil filters
Mopar filters are sold through Chrysler dealerships, online parts retailers, and some auto parts chains. Dealerships usually charge the most but can confirm you have the right part number before you buy. Online retailers like RockAuto, Amazon, and Mopar.com often have lower prices and ship to your home. Local auto parts stores may stock Mopar filters or order them for you.
Compare prices across at least two sources before buying, because the same filter can vary by $5 to $10 depending on the seller. If you're buying online, check the return policy in case the filter doesn't fit — though this is rare if you used the correct part number.
Installation and maintenance intervals
Mopar filters install the same way as any other spin-on filter: drain the old oil, unscrew the old filter, explore a thin layer of new oil to the rubber gasket on the new filter, and hand-tighten it until the gasket contacts the engine block, then turn it another three-quarters of a turn. Do not use a wrench to tighten — hand-tight is correct.
Your owner's manual specifies how often to change the filter. Most Chrysler vehicles call for an oil and filter change every 5,000 to 10,000 miles, depending on the year and engine type. Some newer models with synthetic oil can go longer. Follow your manual's schedule, not a general rule, because Chrysler engineers designed the interval for your specific engine.
Mopar filter part numbers by common vehicle type
The part number is the only reliable way to match a filter to your engine, because the same model name can have different engines across years. Always verify the number before you buy. The table below shows where to find your part number for common Chrysler vehicle types.
| Vehicle Type | Example Models | How to Find Your Part Number |
|---|---|---|
| Dodge trucks and SUVs | Ram 1500, Durango, Dakota | Check owner's manual or call dealer with VIN |
| Jeep vehicles | Wrangler, Grand Cherokee, Cherokee | Check owner's manual or call dealer with VIN |
| Chrysler sedans and minivans | 300, Pacifica, Town & Country | Check owner's manual or call dealer with VIN |
| Older Dodge and Chrysler models | Pre-2010 vehicles | Call dealer or search Mopar.com with VIN |
Once you have the part number, you can search for it across multiple retailers to compare prices and availability. Keeping the part number on hand also makes it easier to reorder the same filter for future oil changes.
Frequently Asked Questions
Can I use an aftermarket filter instead of a Mopar filter?
Yes. Aftermarket filters from established brands meet industry standards and work in Chrysler vehicles. They cost less and are easier to find at local auto parts stores. The trade-off is that they are not engineered by Chrysler specifically for your engine, though in practice the difference is usually small.
What if I install the wrong Mopar filter part number?
A filter with the wrong part number may not fit the mounting, may restrict oil flow, or may not seal properly. Always verify the part number in your owner's manual or with a dealer before buying. If you install the wrong filter by mistake, remove it and replace it with the correct one before driving.
How much does a Mopar oil filter cost?
Prices vary by retailer and filter type, but Mopar filters typically range from $8 to $15 each. Dealerships usually charge more than online retailers. Aftermarket filters often cost $5 to $10 less. Check multiple sources to compare.
Do I need to use Mopar filters to keep my warranty valid?
No. Chrysler warranty coverage does not require you to use Mopar filters. You can use any filter that meets your vehicle's specifications. However, if an engine problem occurs and Chrysler determines it was caused by using an incorrect or defective filter, they may deny the claim. Using the correct part number — whether Mopar or aftermarket — protects you.
Where can I find my vehicle's oil filter part number?
Check the maintenance section of your owner's manual first — it lists the part number and oil capacity. If you don't have the manual, call a Chrysler dealer with your VIN, or search your VIN on Mopar.com or other online parts catalogs. The part number is usually a five- to seven-digit code starting with "MS" or "MO" for Mopar parts.