What You Need Before You Start
A Nissan Altima oil change requires the right oil type, a new filter, basic tools, and about 30 to 45 minutes of work. The specific oil grade and capacity depend on your engine size and model year, so check your owner's manual or the sticker under your hood first — using the wrong viscosity can affect fuel economy and engine wear.
You will need an oil drain pan (to catch old oil), a wrench or socket set to remove the drain plug, an oil filter wrench, a jack and jack stands if you need clearance under the car, and fresh oil. Most Altimas from 2007 onward hold between 3.5 and 4.8 quarts of oil, depending on whether you have a four-cylinder or V6 engine. Buy one extra quart in case you need to top off after the initial fill.
Nissan Altimas typically use either 0W-20 or 5W-30 oil, though newer models (2019 and later) often call for 0W-20. Your owner's manual will specify which one your engine needs. Using a different grade can reduce fuel economy or increase engine stress over time.
Key Takeaways
- Check your owner's manual or the hood sticker to find the correct oil type and capacity for your specific Altima model year and engine.
- The oil drain plug is located on the underside of the engine pan, and the filter is typically on the side or top of the engine block.
- Drain old oil while the engine is warm but not hot, replace the drain plug washer each time, and hand-tighten the new filter rather than using a wrench.
- After refilling with new oil, run the engine for a few seconds, turn it off, wait a minute, and check the dipstick to confirm the level is correct.
Locating the Drain Plug and Filter on Your Altima
The oil drain plug sits on the bottom of the engine oil pan, usually toward the rear or center of the pan. You will need to get under the car to reach it — either use a jack and jack stands or drive onto ramps. Never rely on a jack alone; always use stands to support the vehicle weight.
The oil filter location varies by model year and engine type. On most four-cylinder Altimas, the filter is mounted vertically on the side of the engine block, roughly at mid-height. On V6 models, it is often positioned higher or on the opposite side. If you cannot locate it visually, trace the hose from the engine block — the filter will be at the end of that line.
Before you start, let the engine cool for at least five minutes after running. Warm oil drains faster and more completely, but oil that is too hot can cause burns. A warm engine is the target — not hot to the touch.
Draining Old Oil and Replacing the Drain Plug
Position your drain pan directly under the drain plug. Using the correct wrench or socket size, turn the plug counterclockwise slowly at first — oil may still be warm and can splash. Once the plug is loose enough to turn by hand, unscrew it the rest of the way and set it aside. Let the old oil drain completely into the pan; this usually takes three to five minutes.
While the oil drains, inspect the drain plug washer — the small rubber or metal ring that seals the plug. If it looks cracked, flattened, or damaged, replace it with a new one. A worn washer is the most common cause of slow oil leaks after an oil change. Most auto parts stores sell replacement washers for a few dollars, or they may come with a new drain plug if you choose to replace the whole thing.
Wipe the drain plug clean with a rag, install the new or reused washer, and thread the plug back in by hand first to avoid cross-threading. Once hand-tight, use your wrench to snug it down — firm but not cranked down hard. Over-tightening can strip the threads in the aluminum pan and cause a much bigger problem.
Removing and Installing the Oil Filter
Position your drain pan under the filter to catch any remaining oil. Using an oil filter wrench, turn the filter counterclockwise until it breaks free, then unscrew it by hand the rest of the way. Some oil will spill, so keep the pan close.
Before installing the new filter, wipe the filter mounting surface on the engine with a clean rag to remove any dirt or old rubber. Take the new filter and explore a thin coat of fresh oil to the rubber gasket (the ring around the top of the filter). This helps create a good seal and makes removal easier next time.
Thread the new filter on by hand until the gasket contacts the mounting surface, then turn it an additional three-quarter turn. Do not use a wrench to tighten it — hand-tight is correct. A filter that is too tight can damage the gasket and cause leaks, and it will be nearly impossible to remove next time.
Refilling with New Oil and Checking the Level
Locate the oil filler cap on top of the engine — it usually has an oil can symbol on it. Twist it counterclockwise to remove it. Place a funnel in the opening and pour in the amount of oil specified in your manual, usually between 3.5 and 4.8 quarts depending on your engine. Start with one quart less than the full amount, then check the level before adding the final quart.
Replace the oil filler cap and start the engine. Let it run for about 10 to 15 seconds, then turn it off. Wait one minute for the oil to settle in the pan, then pull out the dipstick, wipe it clean with a rag, reinsert it fully, and pull it out again to read the level. The oil should be between the minimum and maximum marks on the stick.
If the level is low, add a half-quart of oil, wait a minute, and check again. Repeat until the level is correct. Do not overfill — too much oil can damage the engine and cause the check engine light to come on. Once the level is correct, replace the dipstick and the oil filler cap.
Disposing of Old Oil and Resetting the Service Reminder
Never pour old oil down a drain or into the ground — it is toxic and illegal in most places. Take the old oil to a recycling center, auto parts store, or service station that accepts used oil. Many accept it for free, especially if you bought new oil from them. Some Nissan dealerships also accept old oil from customers.
If your Altima has a service reminder light on the dashboard, you may need to reset it manually. On most models, this involves turning the key to the "On" position without starting the engine, pressing the accelerator pedal to the floor three times within 10 seconds, then turning the key off. The light should go out. Check your owner's manual for the exact procedure for your model year, as it varies.
After the oil change, check under the car after a day or two of driving to make sure there are no leaks around the drain plug or filter. A small drip is normal for the first few hours, but any steady leak means the drain plug washer or filter gasket may not be seated correctly.
When to Change Your Altima's Oil
Nissan recommends oil changes every 3,000 to 10,000 miles depending on your model year and driving conditions. Newer Altimas (2009 and later) typically go longer between changes — often 7,500 to 10,000 miles — because synthetic oils last longer than conventional oil. Check your owner's manual or the maintenance schedule sticker under the hood for your specific vehicle.
If you drive mostly on highways at steady speeds, you can usually go toward the longer interval. If you make frequent short trips, tow a trailer, or drive in dusty conditions, stick to the shorter interval. Synthetic oil costs more upfront but lasts longer and provides better protection in extreme temperatures, so it may be worth the extra cost if you plan to keep the car for many years.
Frequently Asked Questions
What oil type does a 2015 Nissan Altima use?
Most 2015 Altimas with a four-cylinder engine use 5W-30 oil, while some V6 models may use 0W-20. Check the sticker under your hood or your owner's manual to confirm the exact grade for your engine. Using the wrong viscosity can affect fuel economy and engine performance.
Can I change the oil myself if I do not have a garage or driveway?
You can, but you need safe access under the car. Many auto parts stores and community centers have lifts you can rent by the hour. Some cities also have tool libraries that loan jacks and stands. Never work under a car supported only by a jack — always use jack stands as backup.
What should I do if the oil drain plug is stuck?
explore penetrating oil (like WD-40) around the plug and let it soak for 15 to 30 minutes. Try again with a wrench that fits snugly — a loose wrench can round off the plug head. If it still will not budge, stop and take the car to a shop rather than risk stripping the threads in the pan.
How do I know if I overfilled the oil?
Check the dipstick after the engine has cooled and settled for a minute. If the level is above the maximum mark, you overfilled it. Drain the excess back into a container until the level is correct. Overfilled oil can cause the engine to work harder and trigger warning lights.
Is synthetic oil worth the extra cost for my Altima?
Synthetic oil lasts longer between changes and performs better in cold and hot temperatures, so it can save money over time if you keep the car long-term. Conventional oil is cheaper per change but requires more frequent changes. The choice depends on your driving habits and how long you plan to own the car.