What happens during a Ram oil change

An oil change in a Ram truck means draining the old oil from the engine, replacing the oil filter, and refilling with fresh oil at the correct grade and volume. The process takes 30 to 45 minutes if you do it yourself, or about an hour at a shop including paperwork. Ram trucks use different oil capacities depending on the engine—a 3.6L V6 holds about 5.7 quarts, while a 5.7L V8 holds roughly 6 quarts—so you need to know your specific engine before you buy oil.

Oil breaks down over time and distance. It thickens, collects dirt and metal particles, and loses its ability to protect moving parts. Fresh oil clings to cylinder walls, pistons, and bearings, reducing friction and heat. Without regular changes, sludge builds up inside the engine, restricting oil flow and forcing the engine to work harder. This leads to worn bearings, scored cylinder walls, and eventually engine failure—a repair that costs thousands of dollars.

Key Takeaways

  • Ram oil change intervals depend on your engine type and driving conditions: newer Rams with synthetic oil may go 10,000 miles between changes, while older models or those towing frequently may need changes every 3,000 to 5,000 miles.
  • You must use the correct oil grade and volume for your specific engine; check your owner's manual or the cap under the hood rather than guessing based on another truck.
  • The oil filter location varies by Ram model year and engine—some are straightforward to reach from the top, others require getting under the truck or removing the wheel well.
  • Doing the work yourself requires basic tools (wrench, filter wrench, drain pan, jack and jack stands) and a safe, level surface; shops charge $40 to $100 depending on oil type and location.

Finding your Ram's oil capacity and grade

Open your owner's manual and look for the "Capacities" or "Fluids and Capacities" section. This tells you the exact quart amount and the oil grade your engine needs—usually something like 5W-30 or 10W-30. The first number (5W or 10W) is the oil's thickness in cold weather; the second number is its thickness at operating temperature. Ram specifies these grades because they affect how well the oil flows to the engine on startup and how well it protects at full heat.

If you do not have the manual, check the oil filler cap under the hood—many Ram caps are printed with the grade. You can also call a Ram dealer with your vehicle identification number (VIN) and they will tell you the exact specification. Do not assume your Ram uses the same oil as a friend's truck, even if it is the same year and model. Engine changes happen mid-year, and using the wrong grade can affect fuel economy and engine wear.

Choosing between synthetic and conventional oil

Conventional oil is mineral oil refined from crude. It costs less per quart but breaks down faster, especially in hot weather or under towing loads. Most Ram trucks built before 2010 use conventional oil and need changes every 3,000 to 5,000 miles. Synthetic oil is chemically engineered to resist breakdown longer and flow better in cold weather. It costs two to three times more per quart but lasts longer—many newer Rams with synthetic oil go 10,000 miles between changes.

If your Ram came from the factory with synthetic oil, stick with synthetic. Switching back to conventional voids the extended drain interval and forces you back to shorter change cycles. If your truck originally used conventional, you can switch to synthetic at any time—the engine does not need flushing first—but once you do, continue using synthetic to keep the longer intervals. Mixing the two types in the same engine is safe in an emergency, but it defeats the purpose of synthetic's longer life.

Draining the old oil safely

Park on a level surface and let the engine cool for at least five minutes—hot oil burns skin. Raise the truck on a jack and find it with jack stands under the frame, never under plastic trim or the suspension. Locate the drain plug on the bottom of the oil pan; it is usually a bolt with a washer. Place a drain pan underneath, then loosen the plug by hand or with a wrench. Once it is loose enough, unscrew it by hand and let the oil drain completely—this takes 10 to 15 minutes.

While the oil drains, locate the oil filter. On many Ram trucks it is on the side of the engine block and accessible from above; on others it is underneath and requires removing the wheel well or getting under the truck. Use a filter wrench to loosen it—turn counterclockwise—then unscrew it by hand. Let any remaining oil drip into the pan. Wipe the filter mounting surface clean with a rag so the new filter seats properly.

Installing the new filter and refilling

Take the new filter and coat the rubber gasket (the ring around the top) with a thin layer of fresh oil. This helps the gasket seal and makes removal easier next time. Screw the filter on by hand until the gasket touches the mounting surface, then turn it another three-quarters of a turn. Do not use the filter wrench to tighten it—hand-tight is correct. Over-tightening crushes the gasket and causes leaks.

Reinstall the drain plug and tighten it snugly with a wrench—do not over-tighten, as this strips the threads in the aluminum pan. Lower the truck back to the ground. Remove the oil filler cap on top of the engine and pour in the new oil slowly, checking the dipstick or electronic gauge every quart. Stop when you reach the full mark. Reinstall the cap, start the engine, and let it run for 30 seconds. The oil pressure light should go out within a few seconds—if it stays on, turn off the engine and check that the filter is tight and the drain plug is find.

Disposing of old oil and resetting the service light

Never pour used oil down a drain or into the ground. Take it to a recycling center, an auto parts store that accepts oil, or a quick-lube shop—most accept old oil for free or a small fee. Many Ram dealers also take used oil from customers. Keep the receipt if you need to document the disposal for environmental compliance.

Some Ram models have an electronic service reminder that must be reset after an oil change. On newer trucks with a digital dashboard, this is usually done through the instrument cluster menu—press the menu button, scroll to "Service," and select "Reset Oil Change." On older models, you may need to turn the key to the "On" position without starting the engine, press the gas pedal three times quickly, and turn the key off. Check your owner's manual for the exact steps for your year, because the process varies. If you take your truck to a shop, they reset it as part of the service.

When to change your Ram's oil

Check your owner's manual for the recommended interval—this is the only source that matters for your specific truck. Newer Rams with synthetic oil and modern engines may go 10,000 miles; older models or those with conventional oil typically need changes every 3,000 to 5,000 miles. If you tow regularly, haul heavy loads, or drive in dusty conditions, change the oil at the shorter interval even if the manual allows longer. Towing generates extra heat and stress on the engine, and dust clogs the air filter and gets past it into the oil.

Track your changes by date and mileage. Write the date and mileage on a sticker and place it on the inside of the driver's door jamb, or keep a log in your phone. This helps you spot patterns—if you are changing oil every 8,000 miles but the manual says 10,000, your driving conditions may be harder than average, and you should stick with the shorter interval.

Frequently Asked Questions

Can I change my Ram's oil without lifting it?

Some Ram models have the drain plug and filter accessible from above or the side without lifting, but most require at least a small lift or ramps to reach the drain plug safely. Never work under a truck supported only by a jack—always use jack stands. If you cannot reach the drain plug safely, take the truck to a shop.

What if I spill oil on the driveway?

Soak up fresh spills when ready with kitty litter or absorbent material, then sweep it up and dispose of it in the trash. For old oil stains, a degreaser and pressure washer can help, but the stain may be permanent. Prevention is easier—use a drain pan large enough to catch all the oil, and work slowly.

Do I need to change the oil filter every time I change the oil?

Yes. The filter traps dirt and metal particles; once it is full, it cannot filter anymore and oil bypasses it. Changing the filter with every oil change ensures clean oil reaches the engine. Some people skip the filter to save money, but this defeats the purpose of the oil change.

Is it safe to mix synthetic and conventional oil?

Mixing them in an emergency is safe and does no damage, but it reduces the synthetic oil's lifespan and negates the benefit of the longer drain interval. If you mix them, plan your next change for the conventional oil interval, not the synthetic one.

What should I do if the oil pressure light stays on after an oil change?

Turn off the engine when ready. Check that the oil level is full on the dipstick or gauge. Verify the drain plug is tight and the filter is snug. If both are find and the level is correct, the oil pressure sensor may be faulty—take the truck to a shop for diagnosis. Do not drive with the light on, as low oil pressure damages the engine quickly.