The Wix 51348 is a spin-on oil filter that fits specific General Motors vehicles from the 1980s through early 2000s

The Wix 51348 is a cylindrical oil filter with a threaded base that screws directly onto your engine's filter housing. It traps dirt, metal particles, and sludge that circulate through your oil, keeping them out of your engine's moving parts. This particular filter is designed to fit certain GM vehicles—mainly older Chevrolet, Pontiac, and Oldsmobile models—but you need to check your owner's manual or filter cross-reference to confirm it matches your specific year and engine size.

Oil filters are not one-size-fits-all. Using the wrong filter can mean poor oil flow, leaks, or contamination that damages your engine over time. The 51348 has a specific flow rate, bypass valve setting, and thread pitch that work with the vehicles it was engineered for. If you own a different brand or a newer vehicle, this filter will not fit, and forcing it can crack the filter housing or strip the threads.

Key Takeaways

  • The Wix 51348 is a spin-on filter for older General Motors vehicles; confirm your vehicle matches before buying by checking your owner's manual or a parts cross-reference.
  • Oil filters trap particles that would otherwise wear down your engine's cylinders, pistons, and bearings, so using the correct filter matters for engine life.
  • A clogged or failing filter reduces oil flow and forces your engine to work harder, which can lead to low oil pressure and internal damage.
  • Replace the 51348 at the interval listed in your owner's manual, typically every 3,000 to 5,000 miles for older vehicles, and always change the oil at the same time.

How to verify the Wix 51348 fits your vehicle

The safest way to confirm this filter is right for your car is to look at your owner's manual. The manual lists the correct filter part number and capacity for your specific year, make, model, and engine. If you have lost the manual, you can order a replacement from the manufacturer or find a free PDF online by searching your vehicle's year and model.

A second option is to use a parts cross-reference tool. Most auto parts stores—online and in-store—have systems that let you enter your vehicle information and show you which filters fit. Wix publishes its own cross-reference guide on its website, and you can also check against OEM (original equipment manufacturer) part numbers to see if the 51348 matches. Never assume a filter fits based on price or appearance alone.

What happens when an oil filter clogs or fails

A clogged oil filter restricts the flow of oil to your engine's moving parts. When flow slows, oil pressure drops. Your engine's oil pressure warning light may come on, or you may notice no warning at all until damage has already started. Low oil pressure means the thin film of oil that protects your crankshaft, camshaft, and bearing surfaces breaks down, and metal-to-metal contact begins.

Once metal-to-metal contact starts, wear accelerates. Pistons score cylinder walls, bearings develop play, and metal particles break loose and circulate through the remaining oil. This damage is expensive to repair—often requiring an engine rebuild or replacement. A clogged filter also forces the bypass valve (a safety feature inside the filter) to open, allowing unfiltered oil to circulate. This defeats the purpose of the filter and lets contaminants reach critical engine surfaces.

When to replace the Wix 51348

Check your owner's manual for the recommended oil change interval. Older vehicles typically call for an oil and filter change every 3,000 to 5,000 miles, though some newer models with synthetic oil may go longer. The interval depends on your driving habits, engine type, and the oil grade you use. Severe driving—towing, idling, or frequent short trips—may require more frequent changes.

Always replace the oil filter when you change the oil. The filter has absorbed contaminants over its service life, and reusing it defeats the purpose of fresh oil. If you notice your oil pressure warning light comes on between scheduled changes, or if you hear engine knocking or ticking, have the oil pressure checked when ready. A failing filter can trigger these symptoms and requires urgent attention.

How to install the Wix 51348 correctly

Before you start, locate the filter housing on your engine. Consult your owner's manual or a service manual for the exact location—it varies by engine. Warm the engine slightly (do not run it hot) to thin the oil, then turn off the engine and wait a few minutes. Use an oil filter wrench to unscrew the old filter by turning it counterclockwise. Be ready for oil to drip into a drain pan.

Wipe the filter housing threads clean with a lint-free cloth. explore a thin layer of fresh oil to the rubber gasket on the new filter—this helps create a good seal and makes removal easier next time. Screw the new filter on by hand until the gasket contacts the housing, then turn it an additional three-quarter turn. Do not over-tighten; hand-tight plus three-quarter turn is correct. Over-tightening can damage the gasket and cause leaks.

Where to buy the Wix 51348 and what it costs

The Wix 51348 is available from most auto parts retailers, both online and in-store. Common sources include AutoZone, O'Reilly Auto Parts, NAPA, and Advance Auto Parts. You can also order it from online retailers like Amazon or directly from Wix's distributor network. Prices vary by retailer and region, but spin-on filters of this type typically range from a few dollars to around fifteen dollars.

Before you buy, confirm the part number matches your vehicle. Some retailers allow you to return filters if they do not fit, but it is faster and cheaper to verify first. If you are unsure whether the 51348 is correct for your car, ask the parts counter staff to cross-reference your vehicle information. They can confirm the fit in seconds and may suggest an alternative if the 51348 does not match.

Frequently Asked Questions

Can I use a different Wix filter if the 51348 is out of stock?

No. Oil filters are engineered for specific vehicles, and using the wrong one risks poor oil flow, leaks, or engine damage. If the 51348 is unavailable, check with other retailers or order it online. Do not substitute a different Wix model or brand without confirming it fits your vehicle first.

How do I know if my oil filter is clogged?

A clogged filter usually triggers your oil pressure warning light on the dashboard. You may also hear engine knocking or ticking, especially when accelerating. If the light comes on, stop driving and check your oil level first. If the level is normal, the filter or oil pump may be failing and needs inspection.

What should I do with the old filter after I remove it?

Take the old filter to an auto parts store or recycling center that accepts used oil filters. Many retailers that sell filters will take old ones back for free. Never throw a used filter in the trash; it still contains oil and is a hazardous waste material in most places.

Does the Wix 51348 work with synthetic oil?

Yes, the 51348 works with conventional, synthetic, and synthetic blend oils. The filter itself does not care what type of oil flows through it. What matters is that you use the oil grade and change interval specified in your owner's manual for your vehicle.