Front strut replacement typically costs between $400 and $1,200 per side, depending on your vehicle, the shop, and whether you replace one or both at once.
A strut is a shock absorber combined with a spring and mounting hardware — it's a single assembly that handles both suspension support and ride comfort. When one fails, you'll notice the car bouncing excessively, dipping hard when you brake, or leaning into turns. Replacing struts is not optional once they wear out; a failed strut affects braking distance and handling.
The total bill breaks into three parts: the strut assembly itself, labor, and any related parts that wear out during the job. Labor typically runs $150 to $300 per side. The strut assembly — the part you're actually buying — ranges from $150 to $600 per side depending on whether you choose an economy, mid-range, or premium brand. Some shops also replace the strut mount, bearing plate, or bump stop while they're in there, which adds $50 to $150 per side.
Key Takeaways
- Front struts usually fail in pairs, so replacing both sides at once costs more upfront but prevents a second repair bill within months.
- Labor makes up roughly half the total cost; the strut assembly itself varies widely by brand and quality level.
- Independent shops often charge less than dealerships for the same strut and the same work, sometimes by $200 to $400 per side.
- Aftermarket struts are cheaper than OEM (original equipment manufacturer) parts but may wear faster or ride differently.
Why struts fail and when replacement becomes necessary
Struts wear out from normal use — every bump, pothole, and braking event compresses them. Most last between 50,000 and 100,000 miles, though this varies by driving conditions. Rough roads, frequent hard braking, and heavy loads speed up wear. A strut that leaks fluid, makes a clunking noise over bumps, or causes the car to sit lower on one side has failed and needs replacement.
Waiting to replace a worn strut costs you money in other ways. A bad strut throws extra stress on the wheel bearing, brake pads, and tires — you may end up replacing those sooner than planned. It also reduces your ability to steer and brake safely, especially in emergency situations. Most mechanics recommend replacing both front struts at the same time, even if only one is obviously worn, because the second one is usually close behind and will fail within a few thousand miles.
Labor costs at different shop types
A dealership typically charges $200 to $350 per side in labor. An independent repair shop usually charges $150 to $250 per side. A chain shop like Firestone or Midas falls somewhere in between, usually $175 to $300 per side. These ranges vary by region — labor rates in urban areas and on the coasts run higher than in rural areas.
The labor difference reflects overhead and warranty policies, not the quality of the work. An independent shop with good reviews will often do the job as well as a dealership for less money. Ask for a written estimate before work begins, and confirm whether the estimate includes replacing the strut mount and bump stop or if those are extra.
Strut assembly prices: OEM versus aftermarket
An OEM strut (original equipment manufacturer) is made by the company that built your car or a licensed supplier. It matches the original part exactly. OEM struts typically cost $300 to $600 per side. An aftermarket strut is made by a third-party manufacturer like KYB, Bilstein, or Monroe. Aftermarket struts usually cost $150 to $300 per side.
The price difference reflects durability and tuning. OEM struts are engineered to match your specific car's weight, suspension geometry, and ride characteristics. Aftermarket struts are engineered to fit a range of vehicles and may prioritize cost over precision. Some aftermarket struts ride harsher or wear faster; others are nearly identical to OEM in performance. Bilstein and KYB struts, for example, are widely used as OEM suppliers and often perform well as aftermarket replacements. Monroe struts are cheaper but may not last as long.
If your car is under warranty, using OEM parts keeps the warranty intact. If your car is older or you plan to keep it only a few more years, an aftermarket strut from a reputable brand is usually the better value.
Additional parts that may need replacement during the job
When a shop removes the strut, they often find other parts that are worn or damaged. The strut mount (also called the strut bearing or top mount) sits at the top of the strut and allows the wheel to turn. It wears out over time and may need replacement at the same time as the strut. Cost: $50 to $150 per side. The bump stop is a rubber cushion that prevents the suspension from bottoming out; it often cracks and should be replaced when the strut is out. Cost: $20 to $50 per side.
The wheel bearing may also be worn if the strut has been bad for a long time. A failing bearing makes a grinding or humming noise that gets louder when you turn. If the shop finds a bad bearing, replacing it adds $150 to $400 per side depending on whether it's pressed on or bolted on. Ask the shop to inspect these parts and give you a separate estimate for any additional work before they start.
Comparing one side versus both sides
Replacing both struts at once is almost always the right choice. The second strut is usually within 10,000 to 20,000 miles of failure, so you'll be back at the shop soon if you replace only one. The labor cost to remove and install is the same whether you do one or two, so the only savings from doing one side is the cost of the strut assembly itself — typically $150 to $300. That savings disappears when you pay labor again a few months later.
If you replace both struts together, your total cost runs $600 to $1,100 for labor and assemblies combined. If you replace one now and one later, you'll pay roughly the same labor cost twice, turning a $600 to $1,100 job into a $900 to $1,650 job spread across two visits. The only scenario where replacing one side makes sense is if the other strut is visibly new or you genuinely cannot afford both at once.
How to reduce the cost
Get quotes from at least two independent shops and one dealership. Independent shops often beat dealership prices by $200 to $400 total. Ask each shop whether they charge extra for the strut mount and bump stop or include them in the labor estimate.
Choose an aftermarket strut from a known brand like KYB or Bilstein instead of OEM if your car is out of warranty. The difference in cost is often $100 to $200 per side with no noticeable difference in ride quality or durability. Avoid the cheapest struts on the shelf; they often fail within 30,000 to 40,000 miles.
If you have an older car with high mileage, ask the shop to inspect the wheel bearings and strut mounts before they start work. Catching a bad bearing early costs less than replacing it after the new strut is installed and the old one is already gone.
Frequently Asked Questions
Can I replace just the shock absorber part and keep the spring?
No. A strut is a single assembly; you cannot separate the shock from the spring in most vehicles. Some shops offer "strut cartridge" replacements, which replace only the internal shock part and reuse the outer housing and spring. This costs less upfront ($200 to $400 per side) but is rarely done because the outer housing and spring often wear at the same rate as the shock. Most mechanics recommend replacing the entire strut.
How long does a strut replacement take?
One to two hours per side, so two to four hours for both sides. Some vehicles are harder to access and may take longer. Ask the shop for a time estimate when you get the quote. Most shops can complete both sides in a single day.
Will my car ride differently after new struts?
Yes, usually better. A worn strut makes the car bounce and lean; a new one restores the original ride. If you choose a different brand or quality level than the original, the ride may feel slightly firmer or softer, but the difference is usually small. Aftermarket struts from major brands feel nearly identical to OEM.
Do I need new struts if the car is only bouncing a little?
If the bounce is noticeable, the strut is worn enough to replace. Worn struts reduce braking distance and steering response even if the bounce is mild. Waiting until the strut completely fails risks losing control in an emergency. Have a shop inspect it; if they confirm it's worn, replace it.
What's the difference between a strut and a shock absorber?
A shock absorber is just the damping part. A strut combines the shock, spring, and mounting hardware into one assembly. Most modern cars use struts on the front and shocks on the rear. Replacing a strut is more involved than replacing a shock because you're removing a structural part of the suspension.