Steel tubing is the foundation of any DIY pushrod setup, and its diameter and wall thickness determine how much load your suspension can handle
A pushrod suspension transfers suspension forces through a rod under compression or tension to a spring and damper mounted elsewhere on the frame — usually inboard. The pushrod itself is almost always steel tubing, typically 4130 chromoly or mild steel DOM (drawn over mandrel) tubing. The choice between them affects cost, weight, and how much abuse the system can take before failing.
4130 chromoly is stronger and lighter than mild steel, which means you can use a smaller diameter or thinner wall and still handle the same load. It costs roughly 40 to 60 percent more than mild steel. Mild steel DOM is heavier but cheaper and easier to weld without special equipment. Most DIY builders use 1-inch to 1.25-inch diameter tubing with 0.058-inch to 0.095-inch wall thickness, depending on the vehicle weight and suspension geometry.
You will also need rod ends (also called heim joints) at both ends of the pushrod to connect it to the control arm and the bellcrank or spring perch. Rod ends come in male and female versions, with different thread sizes. A typical setup uses a 5/8-inch or 3/4-inch rod end. Mismatched sizes or poor-quality rod ends are a common failure point in DIY suspensions because they wear quickly under load and can seize or collapse.
Key Takeaways
- 4130 chromoly tubing is lighter and stronger than mild steel but costs more; mild steel DOM is heavier and cheaper but requires less welding skill.
- Rod ends connect the pushrod to the control arm and bellcrank, and they wear out faster than the tubing itself, so buy quality and plan to replace them.
- Bellcranks are lever arms that redirect pushrod motion and must be sized so the mechanical advantage matches your spring rate and desired suspension travel.
- Coil-over springs and dampers bolt to the bellcrank or frame and must be rated for the load your suspension will see, not just the vehicle weight.
- Fasteners, spacers, and bushings are small parts that fail silently; use Grade 8 bolts and polyurethane or rubber bushings rated for suspension use.
Bellcranks and their role in motion transfer
A bellcrank is a lever arm that pivots on a shaft and converts the vertical motion of the pushrod into the motion needed to compress your spring and damper. It sits between the pushrod and the spring perch. The ratio of the distances from the pivot to the pushrod attachment point and from the pivot to the spring attachment point is called the mechanical advantage, and it directly affects how stiff your suspension feels and how much travel you get.
If the spring attachment is twice as far from the pivot as the pushrod attachment, the mechanical advantage is 2:1 — the pushrod moves half as far as the spring, but the spring sees twice the force. A higher ratio gives you a softer ride and more travel for the same spring rate. A lower ratio (closer to 1:1) gives you a stiffer feel and less travel. Most DIY builders use ratios between 1.5:1 and 2.5:1.
Bellcranks are usually made from aluminum or steel plate, welded or bolted together. Aluminum is lighter but weaker; steel is heavier but can handle more abuse. The pivot shaft is typically 5/8-inch or 3/4-inch diameter steel, and it must be supported by pillow blocks or brackets bolted to the frame. A bellcrank that flexes or moves under load will cause your suspension geometry to change mid-corner, which makes the car unpredictable.
Springs, dampers, and coil-over assemblies
The spring and damper (shock absorber) are bolted to the bellcrank or to a separate spring perch on the frame. Most DIY builders use coil-over assemblies — a spring wrapped around a damper — because they are compact and straightforward to mount. Coil-overs come in different lengths and spring rates, measured in pounds per inch (lb/in).
The spring rate you choose depends on the vehicle weight, the suspension geometry, and how much load the pushrod will transfer to it. A rough starting point is to divide the vehicle weight by four (to get the load on one wheel), then divide that by the expected suspension travel in inches. A 3,000-pound car with 4 inches of travel per wheel needs roughly 150 lb/in springs. But the mechanical advantage of your bellcrank changes this: if your bellcrank has a 2:1 ratio, the spring only needs to be half as stiff, so 75 lb/in.
Dampers must match the spring rate and the suspension travel. A damper that is too soft will allow the car to bounce; one that is too stiff will make the tires lose contact with the road. Most DIY builders buy adjustable dampers so they can tune the compression and rebound separately. Cheap dampers leak or fail within a season; mid-range dampers last a few years with maintenance.
Fasteners and bushings that hold everything together
Every connection in a pushrod suspension is a potential failure point. Use Grade 8 bolts (marked with six radial lines on the head) for all structural connections — the bellcrank pivot, the rod end attachments, and the spring perch bolts. Grade 5 bolts are cheaper but weaker and can shear under hard cornering or bumps.
Bushings isolate the suspension from the frame and allow controlled movement. Rubber bushings are cheap and quiet but wear out in a few years and allow more movement than polyurethane. Polyurethane bushings last longer, allow less movement, and transmit more noise and vibration into the cabin. For a DIY suspension, polyurethane is usually the better choice because it is more predictable and lasts longer. Make sure the bushings are rated for suspension use, not just general automotive use.
Spacers and shims adjust the geometry of your suspension and keep parts from rubbing. They are straightforward to overlook, but a missing spacer can cause a bolt to bend or a rod end to bind. Buy a variety of spacer sizes and keep extras on hand.
Welding and joining methods
Most pushrod tubing is welded, not bolted. If you are welding 4130 chromoly, you need to preheat the tubing to 400 to 500 degrees Fahrenheit before welding and let it cool slowly afterward, or the heat-affected zone will become brittle and crack under load. Mild steel does not require preheating but benefits from it. A MIG welder works for both materials, but TIG welding produces stronger, cleaner welds.
If you do not have welding equipment or experience, you can have the tubing welded by a local shop, or you can use bolted connections with rod ends and clevises (U-shaped brackets). Bolted connections are weaker than welds and require more maintenance because the bolts loosen over time, but they are easier to adjust and repair.
Measuring and sourcing materials
Before you buy anything, draw your suspension geometry to scale on paper or in a CAD program. Mark the pivot points, the attachment points for the pushrod and spring, and the expected range of motion. This tells you the tubing diameter and wall thickness you need, the bellcrank ratio, and the spring rate. Many DIY builders skip this step and end up with a suspension that is too stiff, too soft, or binds at full travel.
Tubing, rod ends, and bellcrank materials are available from online suppliers like Speedway Motors, Summit Racing, and Jegs. Local steel suppliers can cut and bend tubing to your specifications. Coil-over assemblies are available from suspension shops and online retailers; expect to pay $200 to $500 per corner for mid-range quality. Rod ends and fasteners are cheaper — $20 to $50 per rod end, and Grade 8 bolts are a few dollars each.
Common mistakes in material selection
Undersizing the tubing to save weight is the most common mistake. A pushrod that is too thin will flex under load, changing your suspension geometry and making the car unpredictable. It will also fatigue and crack after a few thousand miles. If weight is a concern, use 4130 chromoly instead of mild steel, not thinner walls.
Buying cheap rod ends is another false economy. A rod end that wears out or seizes will leave you stranded and force you to replace the entire pushrod. Spend the extra money on quality rod ends from brands like Speedway or QA1, and plan to inspect and replace them every season if you drive hard.
Mismatching the spring rate to the bellcrank ratio is also common. If your bellcrank has a 2:1 ratio but you buy springs rated for a 1:1 ratio, your suspension will be too stiff and the car will bounce. Use the formula above to calculate the spring rate, then buy springs that match.
Frequently Asked Questions
Can I use aluminum tubing instead of steel?
Aluminum is lighter but much weaker than steel and fatigues faster under repeated loads. For a pushrod that sees suspension forces every time you drive, steel is the safer choice. Aluminum is sometimes used for bellcranks to save weight, but the tubing itself should be steel.
What is the difference between DOM and seamless tubing?
DOM (drawn over mandrel) tubing is stronger and more consistent in wall thickness than seamless tubing because it is drawn through a die after being formed. For suspension use, DOM is the better choice. Seamless tubing is cheaper but has more variation and is weaker.
Do I need to heat-treat the tubing after welding?
If you are welding 4130 chromoly, yes — preheat to 400 to 500 degrees and cool slowly, or have a shop do a stress-relief heat treatment after welding. Mild steel does not require it but benefits from slow cooling. Skipping this step with chromoly will cause the welds to crack under load.
How often do rod ends need to be replaced?
Rod ends wear faster than the tubing because they move constantly. On a car driven hard every weekend, expect to replace them every season or two. On a street car, they may last several years. Inspect them regularly for play or grinding sounds, and replace them before they seize.
What spring rate should I start with if I am not sure?
Use the formula: vehicle weight divided by four, divided by expected suspension travel in inches. For a 3,000-pound car with 4 inches of travel, that is 150 lb/in. Then divide by your bellcrank mechanical advantage ratio. Start conservative — a stiffer spring is easier to soften than a spring that is too soft.