Electric coilovers let you raise or lower your vehicle's ride height from inside the cabin, without tools or a trip to the shop
Electric height-adjustable coilovers are suspension components that combine a shock absorber and spring into one unit, with a motor that changes the spring's compression electronically. Instead of manually adjusting your suspension at each corner—a job that requires tools, knowledge, and time—you press a button or use a phone app to raise the vehicle for highway driving or lower it for cornering and appearance. The motor tightens or loosens the spring perch in real time, so the change happens while you drive.
This is different from traditional coilovers, which you adjust by hand using a wrench on the spring perch, and different from air suspension, which uses pressurized air instead of a mechanical spring. Electric coilovers give you the convenience of air suspension with the durability and tuning precision of a traditional coil spring.
Key Takeaways
- Electric coilovers adjust ride height by motor without stopping the vehicle, so you can lower the car for a show stance and raise it for speed bumps or rough roads.
- The motor, wiring harness, and control module add weight and cost compared to manual coilovers, and the electrical system can fail independently of the suspension itself.
- Installation requires running power and signal wires through the vehicle, integrating with the car's electrical system, and often reprogramming the vehicle's computer to recognize the new suspension.
- Electric coilovers work best on vehicles with existing aftermarket suspension knowledge, because tuning the spring rate and damping still requires the same informed as manual coilovers.
- Repair costs are higher than manual coilovers because a failed motor or control module means replacing the entire coilover unit or sending it to a specialist for rebuilding.
How the motor and control system actually work
Each coilover has a small electric motor mounted to the body of the shock. When you press the button or send a command through an app, the motor turns a threaded rod that moves the spring perch up or down. The amount of rotation determines how much the ride height changes—a quarter turn might lower the car half an inch, while a full turn could change it by two inches or more, depending on the coilover's design.
The control module—a box that sits under the dash or in the engine bay—receives your input and sends power to the motors at each corner. Most systems let you adjust all four corners together or control the front and rear separately. Some allow individual corner adjustment, though that requires four separate buttons or a touchscreen interface. The module also has safety logic built in: it will not let you lower the car so far that the tire rubs the fender, and it will not raise it so high that the suspension runs out of travel.
Power comes from your vehicle's battery, so the system draws current whenever you make an adjustment. A full adjustment cycle at all four corners typically uses less power than running the headlights for an hour, but repeated adjustments during a long drive will show up on the battery if the alternator is not keeping up.
Installation and electrical integration challenges
Installing electric coilovers is not a bolt-on job. The coilovers themselves bolt to the suspension the same way manual ones do, but the electrical work is where the complexity lives. A technician has to run power and signal wires from the battery through the firewall, along the frame rails, and to each corner of the vehicle. Those wires need proper routing, fusing, and grounding to avoid electrical noise that can interfere with the car's other systems.
The control module has to be mounted somewhere accessible—usually under the dash or in the trunk—and connected to the coilover motors with multi-pin connectors. If your vehicle has a modern computer-controlled suspension or stability control system, the new coilover system may need to communicate with that computer so the vehicle knows the suspension height has changed. Some vehicles require reprogramming or a custom interface module to make everything talk to each other.
Professional installation typically takes eight to twelve hours, depending on how much wiring already exists in the vehicle and whether the car's computer needs recalibration. DIY installation is possible if you have experience with automotive wiring and electrical troubleshooting, but a mistake can leave you with a non-functional suspension or a vehicle that will not start.
Tuning the spring rate and damping still requires suspension knowledge
Electric height adjustment is separate from spring stiffness and shock damping. Raising or lowering the car changes the ride height, but it does not change how soft or stiff the suspension feels. You still have to choose the right spring rate when you buy the coilovers, and you still have to adjust the damping (compression and rebound) by hand using adjustment knobs on the shock body.
This means electric coilovers are not a shortcut to a properly tuned suspension. You need to understand what spring rate your vehicle needs based on its weight, how much you plan to lower it, and what kind of driving you will do. You need to know how to adjust damping to prevent the car from bouncing or wallowing. If you are new to suspension tuning, electric coilovers will not make the learning curve any easier—they just add a button to the process you already have to learn.
Some aftermarket shops offer pre-tuned electric coilover packages with recommended settings for specific vehicles, which can save time. But if you want to dial in the suspension yourself, you will still need a flat parking lot, a way to measure ride height, and patience to test different settings.
Cost and repair considerations
Electric coilovers cost more than manual ones—typically 40 to 60 percent more for the coilover units themselves, plus another 500 to 1500 dollars for the control module, wiring, and installation labor. A complete four-corner setup with installation can run 3000 to 6000 dollars depending on the brand and your vehicle.
Repair costs are where the expense really shows. If a motor fails, you cannot just replace the motor—most manufacturers require you to replace the entire coilover unit. A single replacement coilover can cost 800 to 1500 dollars. If the control module fails, that is another 500 to 1000 dollars. A wiring harness failure or connector corrosion can cost 300 to 800 dollars to diagnose and repair.
Some shops specialize in rebuilding electric coilover motors and can do it for less than a full replacement, but this is not available everywhere. Before buying, ask the manufacturer or installer what the warranty covers and whether replacement parts are available locally or if they have to be shipped from overseas.
When electric coilovers make sense versus when they do not
Electric coilovers are worth the cost and complexity if you regularly switch between different ride heights—for example, if you lower the car for car shows or track days and raise it for daily driving on rough roads. They are also useful if you want to adjust the car's stance for different loads, like lowering it when the car is empty and raising it when you are carrying passengers and cargo.
They do not make sense if you plan to set the ride height once and leave it. A manual coilover or a traditional air suspension system will do the same job for less money and less electrical complexity. They also do not make sense if your vehicle is older or has a straightforward electrical system, because integrating a new control module can create reliability problems that did not exist before.
Electric coilovers are also not a substitute for a good alignment shop. After installation, you will need a four-wheel alignment to make sure the suspension geometry is correct at your chosen ride height. If you plan to adjust the height frequently, you may need realignment after major changes, which adds to the long-term cost.
Frequently Asked Questions
Can I adjust the ride height while driving at highway speed?
Yes, most systems allow adjustment while moving, though some manufacturers recommend slowing down to under 30 mph for safety. The adjustment happens gradually over a few seconds, so you will feel the car settle or rise, but it will not jolt or destabilize the vehicle. Check your specific system's manual for speed limits.
What happens if the motor fails while I am driving?
The coilover will stay at whatever height it was at when the motor failed. You can still drive the vehicle normally—the suspension will function as a regular coilover. You will just not be able to adjust the height until the motor is repaired or replaced. The vehicle is safe to drive, but you should have it serviced soon to avoid further damage.
Do electric coilovers work with my car's traction control or stability system?
It depends on your vehicle. Some cars have suspension-aware stability systems that need to know the ride height to calculate wheel angles correctly. If your car has this, the installer will need to integrate the coilover system with the vehicle's computer. If your car has a basic stability system, it will work fine without integration, but you should ask the installer to confirm before purchasing.
Can I use a phone app to adjust the height, or do I need buttons in the car?
Most systems come with physical buttons as the primary control, but some manufacturers offer Bluetooth modules that let you adjust height from a phone app. App control is convenient for show cars or when you want to adjust the height without being inside the vehicle, but it adds another component that can fail. Check the specific product to see what control options are included.
Will electric coilovers void my vehicle's warranty?
Aftermarket suspension modifications typically void the manufacturer's suspension and steering warranty, and may void the powertrain warranty if the installer makes a mistake with the electrical system. Check your warranty paperwork or contact the dealer before installation. Some dealers will allow the work if done by a certified shop, but most will not.