What a 22mm bumpstop is and why it matters
A bumpstop is a rubber or polyurethane block that sits at the end of your suspension travel and stops your suspension from bottoming out completely. Energy Suspension makes a 22mm version—that's the diameter of the rod it fits onto—and it's one of the most common sizes for street vehicles. When your suspension compresses all the way down, the bumpstop is what prevents metal-to-metal contact between your suspension components, which would damage them and send a harsh jolt through the chassis.
The 22mm size fits vehicles with a 22mm diameter suspension rod, typically found on many street cars, light trucks, and older performance vehicles. Without a working bumpstop, your suspension can bottom out during hard braking, rough roads, or when the vehicle is fully loaded. That impact doesn't just feel bad—it can crack welds, bend suspension arms, and damage the shock absorber itself.
Key Takeaways
- A 22mm bumpstop prevents your suspension from bottoming out by cushioning the final inches of compression travel.
- Energy Suspension bumpstops are polyurethane, which lasts longer than rubber and resists oil and heat better.
- You need a new bumpstop when the old one is cracked, compressed flat, or missing—signs include a harsh clunking at the end of suspension travel.
- Bumpstops work alongside shocks and springs; a worn bumpstop can make a vehicle feel unstable on bumpy roads or during hard stops.
- Installation is straightforward on most vehicles and takes 30 minutes to an hour per corner.
How a bumpstop works in your suspension system
Your suspension has a range of motion—it extends when you hit a bump, and it compresses when you brake hard or load weight into the vehicle. Shocks and springs control most of that movement, but they can only do so much. When the suspension reaches the absolute end of its travel, the bumpstop takes over and absorbs the final impact.
Think of it like a shock absorber's backup. The shock does the heavy lifting across the middle of the suspension's range, but the bumpstop is there for the extreme ends. Without it, the suspension arm or strut would slam directly into the frame or chassis, which creates a loud clunk and transfers all that force directly into the vehicle's structure. Over time, that repeated impact cracks welds, bends metal, and wears out the shock faster.
Energy Suspension's polyurethane material is stiffer than OEM rubber bumpstops and doesn't compress permanently. Rubber bumpstops flatten out after a few years of use, especially in hot climates or if the vehicle sits in the sun. Once they're flat, they no longer cushion the impact—they just let the suspension bottom out. Polyurethane resists that permanent compression and lasts longer.
Signs your 22mm bumpstop needs replacement
A worn or failed bumpstop usually announces itself with sound and feel. The most obvious sign is a loud clunking or banging noise that happens at the very end of suspension travel—when you hit a pothole, brake hard, or load weight into the trunk. That noise is the suspension bottoming out because the bumpstop is no longer doing its job.
Look at the bumpstop itself if you can access it. If it's cracked, split, or visibly compressed flat, it needs to be replaced. A healthy bumpstop should have some give when you press it by hand, but it should spring back. If it stays compressed or feels like hard plastic, it's worn out. You might also notice the vehicle feels harsher over bumps, or the suspension seems to bottom out more easily than it used to.
Some vehicles have bumpstops on the front struts and rear shocks, while others have them only on certain corners. Check your vehicle's suspension layout to know which ones to inspect. If you've recently replaced shocks or springs and the clunking persists, the bumpstops are likely the culprit.
How to install an Energy Suspension 22mm bumpstop
Installation depends on whether your bumpstop sits on a shock rod (most common) or is mounted to the frame. For a shock-mounted bumpstop, the process is straightforward: compress the shock by hand or with the vehicle's weight on it, slide the old bumpstop off the rod, and slide the new one on. The bumpstop should sit at the very top of the shock rod, where it contacts the shock's upper mount or the frame when the suspension is fully compressed.
On some vehicles, you'll need to remove the shock or strut to access the bumpstop easily. If that's the case, support the vehicle safely with jack stands, remove the wheel, unbolt the shock from the frame and suspension arm, and then remove the bumpstop from the rod. Install the new Energy Suspension bumpstop, reinstall the shock, and torque all bolts to the vehicle's specification.
The whole job usually takes 30 minutes to an hour per corner if you're working on one shock at a time. You don't need special tools—just a jack, jack stands, and a socket set. If you're not comfortable working under the vehicle, a shop can do this in under an hour and charge accordingly. Always replace bumpstops in pairs (both fronts or both rears) so the suspension compresses evenly.
Energy Suspension polyurethane versus OEM rubber bumpstops
OEM (original equipment manufacturer) bumpstops are usually made of rubber, which is softer and cheaper to produce. They work fine when new, but rubber degrades in sunlight and heat, and it compresses permanently over time. After three to five years, depending on climate and use, rubber bumpstops flatten out and lose their cushioning effect.
Energy Suspension's polyurethane bumpstops are harder and more durable. They resist UV damage, oil, and heat better than rubber, and they don't compress permanently. The trade-off is that polyurethane is slightly stiffer, so the final bump at the end of suspension travel feels a bit firmer. For most street vehicles, that difference is barely noticeable—you're still getting a cushion, just a more durable one.
Polyurethane bumpstops typically last 8 to 10 years or longer, compared to 3 to 5 years for rubber. If you live in a hot climate or your vehicle spends a lot of time in the sun, polyurethane is the better choice. The cost difference is usually $10 to $20 per bumpstop, which is worth it for the longer lifespan.
What happens if you ignore a worn bumpstop
Driving on a failed bumpstop doesn't cause when ready catastrophic failure, but it accelerates wear on other suspension parts. Every time the suspension bottoms out without cushioning, the shock absorber takes the full impact. That repeated shock can crack the shock's internal seals and damage the piston rod, leading to a leaking shock that loses its damping ability.
The suspension arms and frame also take repeated impacts, which can crack welds or bend metal over time. You might notice the vehicle becoming less stable on bumpy roads, or the suspension feeling "loose" because the worn bumpstop isn't controlling the final bit of travel. In extreme cases, a completely failed bumpstop can allow the suspension to bottom out so hard that it damages the shock rod itself, which is expensive to repair.
The cost of replacing a bumpstop is low—usually $30 to $80 in parts and labor combined. Ignoring it and letting it damage a shock or suspension arm can cost $300 to $800 or more. Replacing bumpstops as part of regular maintenance is one of the cheapest ways to protect the rest of your suspension.
Frequently Asked Questions
Can I drive with a cracked or missing bumpstop?
Yes, but you shouldn't for long. A cracked bumpstop no longer cushions the suspension, so you'll hear clunking and the suspension will bottom out more easily. This accelerates wear on shocks and suspension arms. Replace it as soon as you notice the problem.
Do I need to replace both front bumpstops at the same time?
Yes. If one is worn, the other likely is too, and replacing them in pairs ensures even suspension compression. If you replace only one side, the suspension will compress unevenly, which can affect handling and stability.
Is a 22mm bumpstop the right size for my vehicle?
The 22mm refers to the diameter of the shock rod it fits onto. Check your shock's rod diameter or look up your vehicle's specification. Using the wrong size won't fit properly and won't protect your suspension. A parts shop or mechanic can confirm the correct size for your vehicle.
Will a polyurethane bumpstop make my ride harsher?
Slightly, but most drivers don't notice the difference. Polyurethane is firmer than rubber, so the final bump at the end of suspension travel feels a bit more solid. For normal driving, this is negligible. The benefit of durability usually outweighs the minor change in feel.
How often should bumpstops be replaced?
Rubber bumpstops typically last 3 to 5 years, while polyurethane lasts 8 to 10 years or longer. Replace them when you notice clunking, visible cracks, or permanent compression. If you're replacing shocks, it's a good time to replace bumpstops too.