What a rear shock upgrade does on the Engwe M20
The Engwe M20 comes with a basic coil spring rear shock that absorbs bumps but offers no adjustment and little damping control. Upgrading to an air shock or a quality adjustable coil shock changes how the bike handles rough ground, how much energy you feel through the frame, and how predictable the rear wheel stays in contact with the ground. A better shock means fewer jarring impacts on your body, more control when braking hard, and a ride that feels planted rather than bouncy.
The stock shock is adequate for casual riding on smooth surfaces. But if you ride unpaved roads, hit potholes regularly, carry heavy loads, or want the bike to feel more responsive, the upgrade pays for itself in comfort and handling. The rear shock is one of the few suspension parts on the M20 that you can actually replace with something meaningfully better without major frame modifications.
Key Takeaways
- The Engwe M20 uses a 190 mm coil spring shock mounted between the seat tube and rear axle, and most aftermarket shocks fit this same mounting without frame changes.
- Air shocks offer adjustable ride height and damping but cost more and require a pump; quality coil shocks are cheaper and need no maintenance but offer less tuning.
- Measure your current shock's eye-to-eye length and stroke before ordering a replacement, because the wrong size will not fit or will change the bike's geometry.
- Installation requires removing the rear wheel and unbolting the shock at both ends, a job that takes 30 to 45 minutes with basic tools and no special knowledge.
- A shock upgrade alone will not fix poor braking or steering; it only improves how the rear wheel tracks bumps and how the frame absorbs impact.
Shock types that fit the Engwe M20
The M20 frame accepts shocks with a 190 mm eye-to-eye distance (the space between the bolt holes at each end). Within that constraint, you have three main options: the stock coil spring, an air shock, or an upgraded coil shock.
Coil spring shocks use a metal spring to push back when compressed. They are straightforward, require no maintenance, and cost less than air shocks. The downside is that you cannot adjust spring rate or damping without replacing the entire shock. Brands like RockShox Monarch and Fox Float make quality coil shocks, but they are expensive. Budget coil shocks from brands like Suntour or SR Suntour are cheaper but offer less control and wear out faster.
Air shocks use compressed air instead of a spring. You adjust the air pressure with a pump to change how stiff the shock feels, and many air shocks also let you tune damping (how fast the shock compresses and extends). This flexibility is valuable if you switch between road and off-road riding or if your weight changes. The trade-off is cost—air shocks run two to four times the price of basic coil shocks—and you need a shock pump to adjust them. Air shocks also need occasional maintenance to keep the seals working.
For the M20 specifically, air shocks are less common because the bike is not designed around them and the frame geometry is already set. A coil shock upgrade is usually the better choice: it fits without fuss, costs less, and improves the ride noticeably over stock.
Measuring and confirming the right shock size
Before you order a replacement, you must measure your current shock to confirm the size. The Engwe M20 uses a 190 mm shock, but "190 mm" refers to the eye-to-eye distance—the length from the center of the bolt hole at the top to the center of the bolt hole at the bottom when the shock is fully extended. This is not the same as the total length of the shock body.
To measure, remove the rear wheel and unbolt the shock at the seat tube end. Extend it fully by hand (do not force it). Measure from the center of the top bolt hole to the center of the bottom bolt hole with a ruler or caliper. Write down this number. Also measure the stroke—how far the shock compresses from full extension to full compression. On the M20, this is usually 50 to 60 mm. A shock with the wrong eye-to-eye distance will either not bolt in or will change the seat tube angle and bottom bracket height, making the bike handle differently.
When shopping for a replacement, search for shocks listed as "190 mm" or "M20 compatible." If you find a shock you like but the listing does not specify the eye-to-eye length, contact the seller or manufacturer before buying. Returning a shock that does not fit costs time and money.
How to remove and install the rear shock
Removing the shock takes about 15 to 20 minutes. You will need a socket wrench or hex key that fits the bolt heads (usually 8 mm or 10 mm), a shock pump if you are installing an air shock, and a work stand or way to hold the bike steady. Flip the bike upside down or use a stand to keep the rear wheel off the ground.
First, remove the rear wheel by unbolting the axle nuts or quick-release lever. This gives you access to the shock mounting points. Unbolt the shock at the seat tube (top) first—usually one bolt. Then unbolt it at the rear axle (bottom)—usually one bolt. Slide the old shock out. Clean any dirt or rust from the bolt holes and the frame.
Slide the new shock into place, aligning the bolt holes. Insert the bolts by hand first to make sure they thread straight, then tighten them firmly with your wrench. Do not over-tighten; you want them snug, not stripped. If you installed an air shock, use the shock pump to inflate it to the pressure recommended by the manufacturer (usually printed on the shock body or in the manual). Reinstall the rear wheel and spin it to make sure it does not rub the frame or shock.
Test the bike on flat ground first. Bounce gently on the seat to feel how the shock responds. If it feels too soft or too hard, adjust the air pressure (if it is an air shock) or accept that a coil shock cannot be tuned without replacement. Take a short ride on a smooth surface before heading to rough ground.
What improves and what does not change
A rear shock upgrade improves how the bike absorbs bumps and how the rear wheel stays in contact with the ground on uneven surfaces. You will feel fewer jarring impacts through the seat and handlebars, and the bike will feel more stable when you brake hard or accelerate over rough ground. If you carry heavy loads, a better shock helps the frame stay level instead of sagging at the rear.
A shock upgrade does not improve braking power, steering response, or how the front wheel handles bumps. It does not make the bike faster on flat ground. It does not fix a bent frame or worn bearings. If your M20 pulls to one side or the brakes feel spongy, those are separate issues that a shock upgrade will not solve. Think of the shock as one piece of the suspension system; upgrading it only improves that one piece.
Cost and durability expectations
A basic replacement coil shock for the M20 costs between $40 and $120, depending on brand and build quality. Mid-range shocks from established brands like Suntour run $80 to $150. Air shocks start around $200 and can exceed $400. Installation is a one-time cost if you do it yourself; a bike shop will charge $30 to $60 for labor.
A quality coil shock should last 2 to 4 years of regular riding before the spring loses stiffness or the damping wears out. Air shocks last longer if maintained but need occasional seal replacement. Budget shocks wear out faster—sometimes in 12 to 18 months—especially if you ride rough terrain regularly. The more you spend upfront, the longer the shock will perform well and the less often you will need to replace it.
Common mistakes to avoid
The most common mistake is ordering a shock without confirming the eye-to-eye length. A shock that is too long will not fit; one that is too short will compress too easily and bottom out on bumps. Always measure before you buy.
Another mistake is over-tightening the mounting bolts. The frame around the shock mounts is aluminum and can crack if you wrench too hard. Tighten until snug, then stop. If a bolt spins without tightening, the hole may be stripped—stop and seek help from a bike shop rather than forcing it.
Do not assume that a more expensive shock is always better for your riding. A $300 air shock is wasted money if you only ride smooth paths; a $60 coil shock will serve you better. Match the shock to how and where you actually ride.
Frequently Asked Questions
Can I use a shock from a different bike brand on my Engwe M20?
Only if it has the same 190 mm eye-to-eye distance and the same mounting bolt size. Many bikes use 190 mm shocks, so cross-brand compatibility is possible, but you must measure and confirm before buying. Do not assume two shocks are the same size just because they look similar.
What air pressure should I run in an air shock?
The manufacturer prints a pressure range on the shock body or in the manual, usually between 80 and 200 psi depending on the shock model and your weight. Start at the middle of the range and adjust up if the shock feels too soft or down if it feels too stiff. Write down the pressure you like so you can return to it after maintenance.
Do I need to bleed air out of an air shock before removing it?
Yes. Use the shock pump to release all air pressure before unbolting it. A pressurized shock can suddenly extend when you remove the bolts, which is dangerous and can damage the frame or your hands. Most shock pumps have a release valve for this purpose.
Will upgrading the rear shock make my Engwe M20 climb hills better?
No. A shock upgrade improves comfort and control on bumpy ground, but it does not change the motor power, gearing, or weight distribution that determine climbing ability. If hill climbing is your goal, focus on motor power and battery capacity instead.
How do I know if my shock is worn out and needs replacement?
A worn shock will feel mushy or will not return to full extension after a bump. You may notice the rear end sagging lower than it used to, or the bike bottoming out on small bumps. If the shock leaks oil or makes creaking sounds, it is time to replace it.