What a CV joint replacement involves and what it costs
A CV joint replacement means removing the axle shaft, unbolting the old joint, pressing or sliding the new one into place, and reinstalling the shaft. On a front-wheel-drive car, you typically replace the entire axle assembly rather than just the joint itself — it is faster and often cheaper than pressing a new joint onto the old shaft. On rear-wheel-drive vehicles with independent rear suspension, you may replace just the joint.
The job takes two to four hours at a shop, depending on whether the axle is stuck or corroded. Parts cost between $150 and $400 per side for an axle assembly, or $80 to $200 if you are replacing only the joint. Labor runs $200 to $600 per side at an independent shop, or $300 to $800 at a dealership. Total cost is usually $400 to $1,000 per side.
If you have basic mechanical skills and the right tools, you can do this yourself and save the labor cost. The main obstacles are access — you may need to remove the wheel well liner or suspension components — and getting the axle out if it is seized. A hydraulic press is needed if you are replacing just the joint rather than the whole axle.
Key Takeaways
- Most front-wheel-drive cars use a complete axle assembly replacement, which is faster than pressing a new joint onto the old shaft.
- You will need a jack, jack stands, a socket set, a pry bar, and possibly a hydraulic press or axle puller, depending on your vehicle and which parts you are replacing.
- The axle bolts to the transmission on one end and the wheel hub on the other; both connections must be unbolted before the shaft comes free.
- New CV joints come packed in grease; if you reuse the old shaft, you must clean it thoroughly and pack the new joint with the correct grease before installation.
- A stuck or corroded axle can add hours to the job; penetrating oil and heat applied the night before make removal much easier.
Tools and parts you will need
Start with a floor jack and jack stands — never work under a car supported only by a jack. You also need a socket set (usually 17 mm, 19 mm, and 21 mm sockets for most vehicles), a breaker bar to loosen the axle nut, a pry bar to separate the axle from the transmission, and a ball joint separator or pickle fork to disconnect the lower control arm from the steering knuckle if your vehicle requires it.
For the axle itself, you may need an axle puller (a three-jaw puller bolted to the wheel hub) if the shaft is stuck in the hub. If you are replacing only the joint and not the whole axle, a hydraulic press is nearly essential — trying to hammer a joint off by hand risks damaging the shaft. A bearing puller may also be needed to remove the old joint from the shaft.
Parts-wise, order a complete axle assembly if available for your vehicle, or a CV joint kit that includes the joint, boots, and grease. Check your owner's manual or parts catalog for the correct part number; left and right axles are often different lengths. Have new axle nuts on hand — these are often torque-to-yield and should not be reused.
Removing the old axle and joint
Raise the vehicle on a jack and find it with jack stands under the frame. Remove the wheel and the wheel well liner if present. Unbolt the axle nut (usually 17 mm or 19 mm) — this nut is tight and may require a breaker bar. Some vehicles have a cotter pin or lock washer; remove those first.
Next, unbolt the axle from the transmission. On most front-wheel-drive cars, the axle bolts to a flange on the transmission with three or four bolts. Use a pry bar to separate the axle from the transmission — it will not slide out easily. Work the pry bar between the transmission and the axle flange, not between the transmission and the engine.
If your vehicle has a lower control arm connected to the steering knuckle, unbolt that connection or use a ball joint separator to pop it apart. Then pull the wheel hub and steering knuckle outward, sliding the axle out of the hub. If the axle is stuck in the hub, use an axle puller: bolt it to the wheel hub studs and tighten the center screw until the axle slides out.
Once the axle is free, take it to a workbench. If you are replacing the whole axle, you are done with removal. If you are replacing only the joint, use a hydraulic press to push the old joint off the shaft, or use a bearing puller if the joint has a snap ring. Clean the shaft thoroughly with a wire brush and degreaser before installing the new joint.
Installing the new CV joint or axle
If you are installing a new joint on the old shaft, use a hydraulic press to push it onto the shaft until it seats fully — the joint should not move by hand once installed. Pack the joint with the grease supplied in the kit, working it into the races and around the balls. Install the new boots (rubber covers) and find them with the clamps provided, tightening the clamps with a screwdriver or clamp tool.
If you are installing a complete new axle assembly, inspect the splines on the shaft and the hub for damage. Slide the axle into the hub first, then guide the transmission end into the transmission flange. Hand-tighten the transmission bolts before fully seating the axle — this prevents cross-threading.
Bolt the axle to the transmission with the correct torque (usually 30 to 50 foot-pounds for the flange bolts; check your manual). Reconnect the lower control arm if you disconnected it, torquing the ball joint bolt to spec. Install a new axle nut and tighten it to the torque specified in your manual — this is often 150 to 200 foot-pounds, but varies widely. Some axle nuts must be staked (bent over) after tightening to prevent loosening.
Reinstalling the wheel and checking your work
Reinstall the wheel well liner if you removed it, then mount the wheel and hand-tighten the lug nuts. Lower the vehicle to the ground and torque the lug nuts in a star pattern to the specification in your manual (usually 80 to 120 foot-pounds). Spin the wheel by hand — it should rotate freely without grinding or clicking.
Take the vehicle for a short test drive at low speed, listening for clicking or clunking from the CV joint area when turning. A new joint may click slightly at full lock for the first few miles as the grease settles, but the noise should diminish. If clicking persists or gets worse, the joint may not be fully seated or the boot may be torn.
Check the transmission fluid level after the job — you may have lost some fluid when you disconnected the axle. Top up if needed. If the vehicle pulls to one side or the steering feels off, the wheel alignment may have shifted; have it checked at a shop.
When to replace both sides and what to watch for
If one CV joint has failed, the other side is often close behind, especially if both are original equipment on a high-mileage vehicle. Many shops recommend replacing both axles at the same time to avoid a second job in a few months. The labor cost is only slightly higher for both sides, and you get consistent wear and performance.
Watch for these signs that a joint is failing: clicking or popping when turning, vibration at highway speed, or grease leaking from a torn boot. A torn boot allows water and dirt into the joint, causing rapid wear. If you catch a torn boot early, you can sometimes replace just the boot and repack the joint with fresh grease, saving the cost of a new axle. However, if the joint is already clicking, the races are likely damaged and the whole axle must be replaced.
If the axle nut was not torqued correctly or was not staked, it can loosen over time, causing the axle to rattle or even separate. This is dangerous. If you hear a new rattle from the front end after a CV joint replacement, stop driving and have the axle nut checked when ready.
Frequently Asked Questions
Can I drive on a bad CV joint?
You can drive short distances, but a clicking or clunking joint will worsen quickly. The joint may eventually seize or separate, causing loss of power to that wheel. Have it replaced as soon as possible to avoid being stranded.
What is the difference between replacing the joint and replacing the whole axle?
Replacing just the joint requires a hydraulic press and is time-consuming. Replacing the whole axle is faster and usually cheaper at a shop. Most shops recommend the whole axle because the labor is nearly the same and you get a warranty on the entire assembly.
Do I need to realign the wheels after a CV joint replacement?
Not always. If you only disconnected the axle and did not touch the suspension, alignment should not change. However, if you disconnected the lower control arm or ball joint, have the alignment checked afterward.
How long does a new CV joint last?
A properly installed CV joint with a good boot should last 80,000 to 100,000 miles or more. If the boot tears, water and dirt enter the joint and it may fail in 10,000 to 20,000 miles. Inspect boots regularly for cracks or leaking grease.
What if the axle nut spins but does not tighten?
The threads on the shaft or hub may be stripped. Try a new nut first — sometimes the old nut is damaged. If the new nut still spins, the shaft threads are stripped and the axle must be replaced or the shaft must be rethreaded at a machine shop.