What Kelderman air suspension is and why truck owners choose it
Kelderman air suspension is an aftermarket system that replaces your truck's factory coil or leaf springs with air springs — pressurized bags that support your vehicle's weight. Instead of metal springs that compress at a fixed rate, air springs adjust their stiffness by changing the amount of air inside them, which means you can raise or lower your truck and change how it rides without swapping out hardware.
Truck owners install Kelderman systems for three main reasons: to level a truck that sags under load, to gain extra ground clearance, or to smooth out a rough ride when towing or carrying heavy cargo. The system uses an onboard air compressor and a control module so you can adjust suspension height and firmness from inside the cab while driving or parked.
Kelderman is one brand among several air suspension manufacturers — others include Air Lift, Firestone, and Ridetech — but Kelderman focuses specifically on light-duty and medium-duty trucks, which is why you see their systems on work trucks and towing vehicles.
Key Takeaways
- Kelderman air suspension replaces coil or leaf springs with pressurized air bags that you can adjust from inside your cab to change ride height and firmness.
- The system includes an onboard compressor, air lines, a control module, and height sensors that work together to maintain the pressure and level you set.
- Air suspension levels a sagging truck bed under load, reduces bouncing when towing, and lets you raise the truck for clearance without a permanent lift kit.
- Installation requires removing the factory suspension components and running air lines through the frame, which typically takes a shop several days and costs between $3,000 and $6,000 depending on your truck model.
- Air suspension needs annual maintenance — checking compressor function, inspecting air lines for leaks, and replacing the desiccant cartridge that keeps moisture out of the system.
How the components work together
A Kelderman system has five main parts: the air springs (the bags themselves), the compressor (which pressurizes the air), the control module (the brain that decides when to add or release air), height sensors (which tell the module how high the truck is sitting), and the air lines and fittings that connect everything.
When you adjust the height dial in your cab, you are telling the control module to either pump more air into the springs or let air out. The height sensors measure how much the suspension has compressed and signal the module to stop when you reach the level you want. If you load your truck bed with cargo, the springs compress, the sensors detect the drop, and the compressor automatically adds air to bring the truck back to level — this is called load-leveling, and it is the main reason people choose air suspension over a straightforward lift kit.
The compressor runs on 12-volt power from your battery and usually cycles on for a few seconds when needed, then shuts off. Because the system is sealed, the air stays pressurized even when the truck is parked, so your truck will hold its height overnight. If you notice the truck slowly sinking over days or weeks, that signals a slow leak in an air line or spring, which needs repair.
What changes when you install Kelderman suspension
The ride quality shift depends on what you are replacing. If your truck came with coil springs, the air suspension will usually feel softer and more controlled because air springs absorb bumps more gradually than metal springs do. If you are replacing leaf springs — common on trucks with solid rear axles — the difference is even more dramatic: leaf springs are stiff and transfer a lot of shock to the frame, while air springs isolate that shock better.
The trade-off is complexity. Factory coil and leaf springs need almost no maintenance and rarely fail. Air suspension has more parts that can leak, wear out, or malfunction. The compressor can fail. Air lines can crack or develop slow leaks. The control module can develop electrical faults. None of these are catastrophic — a slow leak just means the truck gradually sinks and you need to have it serviced — but they do require attention.
Height adjustment is the feature that changes how you actually use the truck. You can lower the truck 2 to 4 inches for easier loading and unloading, then raise it back up for highway driving or to clear obstacles. Some owners raise the truck an extra 2 to 3 inches for off-road clearance. This flexibility is not possible with a fixed lift kit, which is why air suspension appeals to people who need different ride heights for different jobs.
Installation: what the work involves and what it costs
Installing Kelderman suspension is not a bolt-on job. The shop has to remove your factory suspension components — coils, shocks, or leaf springs — and install the air springs in their place. This means lifting the truck, unbolting the axles or control arms, and carefully positioning the new springs so they sit at the right angle and height.
The compressor mounts somewhere in the engine bay or under the truck, usually near the frame rail. Air lines run through the frame to each corner of the truck, and the control module mounts inside the cab, often under the dash or in the center console. The height sensors bolt to the suspension and connect to the module with wiring. All of this takes time: a typical installation takes 3 to 5 days depending on the truck model and whether the shop has done that model before.
Cost varies by truck. A full Kelderman system for a half-ton pickup typically runs $3,500 to $6,000 installed, including parts and labor. Medium-duty trucks or custom setups cost more. Some shops charge $1,500 to $2,500 just for labor, so the final bill depends on your truck and your local shop rates. Get quotes from shops that have experience with Kelderman systems on your specific truck model — they will give you a more accurate price and timeline.
Maintenance and common problems
Air suspension is not maintenance-free. Once a year, have the shop check the compressor for proper operation, inspect all air lines for cracks or leaks, and test the control module's response. Most shops charge $150 to $300 for a full inspection. If they find a slow leak, they can usually pinpoint it with soapy water — bubbles form where air is escaping — and repair or replace the leaking component.
The desiccant cartridge is a small filter that removes moisture from the air before it enters the springs. Moisture inside the system can corrode the springs and compressor from the inside. The cartridge should be replaced every 2 to 3 years, or more often if you live in a humid climate or use the truck in wet conditions. Replacement costs $50 to $150 depending on the cartridge type.
The most common failure is a slow leak in an air line or spring. You will notice the truck gradually sinking over a week or two, or the compressor running more often than usual. This is not an emergency — the truck will not suddenly drop — but it does need repair. A leaking air line can often be replaced for $200 to $400. A leaking air spring is more expensive, typically $400 to $800 per corner, because the spring itself has to be replaced.
Compressor failure is less common but more costly. A failed compressor usually means the truck cannot adjust height anymore, and the compressor has to be replaced — typically $800 to $1,500 installed. Control module failures are rare but can happen if the module gets wet or is damaged. Module replacement runs $500 to $1,000.
Air suspension versus other lifting options
A fixed lift kit — coils, springs, or blocks that permanently raise the truck — costs less upfront ($1,000 to $3,000 installed) and needs almost no maintenance. But it raises the truck permanently, which can make loading and unloading harder and can affect how the truck handles on the highway. A lift kit also does not level the truck under load, so if you tow or carry heavy cargo, the rear will still sag.
Airbags (also called air springs or air suspension) cost more upfront but give you adjustable height and automatic load-leveling. You pay for that flexibility with more maintenance and more things that can fail. If you tow regularly, haul heavy loads, or need different ride heights for different jobs, air suspension usually pays for itself in comfort and convenience. If you just want a slightly higher truck for looks, a fixed lift kit is simpler and cheaper.
Coilover suspension — adjustable coil springs with dampers — is another option that sits between fixed lifts and air suspension. Coilovers let you adjust height and stiffness but require manual adjustment and do not auto-level under load. They are popular on performance trucks but less common on work trucks.
Signs your air suspension needs service
Watch for these warning signs: the truck sinking slowly over days or weeks (slow leak), the compressor running constantly or very frequently (system losing pressure), uneven ride height at the corners (sensor or module problem), or a hissing sound when you adjust height (air line leak). Any of these means the system needs inspection.
If the truck suddenly drops on one corner and will not raise back up, a spring or line has likely failed completely. This is not safe for highway driving — the truck will handle poorly and the tire may rub the fender — so have it towed to a shop rather than driving it.
Frequently Asked Questions
Can I install Kelderman air suspension myself?
Not unless you have suspension experience and proper tools. The work requires lifting the truck safely, unbolting suspension components, and running air lines and wiring through the frame. A mistake can affect how the truck handles or cause a leak. Have a shop with Kelderman experience do the installation.
Will air suspension void my truck's warranty?
It may void the suspension and steering warranty, depending on your truck's manufacturer and warranty terms. Check your warranty documents or contact the dealer before installation. Some dealers will not service suspension-related issues on trucks with aftermarket air suspension, so factor that into your decision.
How long do Kelderman air springs last?
Air springs typically last 5 to 10 years depending on use and maintenance. Springs that are regularly adjusted and kept clean tend to last longer. If you notice a leak or the truck sinking, have it inspected — a spring may be failing and need replacement.
Can I adjust the height while driving?
Yes, most Kelderman systems let you adjust height while moving, though some shops recommend adjusting only at low speeds. Check your system's manual or ask the installer. Adjusting height while driving is useful for clearing obstacles or smoothing the ride, but do not make large adjustments at highway speeds.
What happens if the compressor fails?
If the compressor fails, the truck will not be able to adjust height or auto-level under load. The air in the springs will stay at whatever pressure it was at when the compressor quit, so the truck may sit higher or lower than normal. You can still drive it, but you should have the compressor replaced soon to restore full function.