An LS trunnion upgrade replaces the factory upper control arm ball joint with a stronger, more durable component designed to handle lifted trucks and heavier loads without premature wear or failure.

The trunnion is the upper ball joint on your control arm — the pivot point where your wheel hub connects to the suspension frame. On factory LS (and similar light-duty truck) suspensions, this joint uses a pressed-in ball stud that can wear out quickly under stress, especially if you've lifted the truck, added weight, or drive on rough terrain. An LS trunnion upgrade replaces this weak point with an aftermarket unit that uses a threaded, rebuildable design instead of a pressed joint.

The difference matters because a worn or failed upper ball joint doesn't just feel loose — it changes your wheel alignment, makes steering unpredictable, and can eventually cause the wheel to collapse inward during hard turns or bumps. A trunnion upgrade prevents that failure mode and extends the life of your suspension by 50,000 to 100,000 miles or more, depending on how hard you drive.

Key Takeaways

  • A trunnion upgrade replaces a pressed ball joint with a threaded, rebuildable design that lasts longer and handles lifted or loaded trucks better.
  • Factory LS ball joints wear out faster under lifted suspension, added weight, or aggressive off-road use because the pressed design has no adjustment or rebuild path.
  • The upgrade costs between $300 and $600 per side in parts and labor, and takes 2 to 4 hours per side to install.
  • You will notice the difference most if you have lifted your truck more than 2 inches or regularly tow or carry heavy loads.
  • A worn upper ball joint causes vague steering, clunking noises over bumps, and uneven tire wear on the inside edge of the tire.

How the Factory LS Ball Joint Fails

The factory upper control arm on LS trucks uses a pressed ball stud — a tapered metal shaft pressed into the control arm housing with no threads and no way to adjust or replace it without replacing the entire arm. This design is cheap to manufacture and works fine for stock suspension on normal roads. But the press fit creates a weak point: the ball stud can loosen in its socket, wear out the rubber boot that keeps dirt out, and eventually develop play that makes the steering feel sloppy.

Lifted trucks accelerate this wear because the suspension geometry changes. When you raise the truck 2 inches or more, the angle of the control arm increases, putting more side-load on the ball joint. Add towing, hauling, or off-road driving, and the joint wears out in 40,000 to 80,000 miles instead of the 100,000+ you might get on stock suspension. Once it starts to wear, there is no fix except to replace the entire control arm — a $400 to $800 job per side.

What a Trunnion Upgrade Changes

An LS trunnion upgrade uses a threaded ball stud design that screws into the control arm instead of being pressed in. The stud sits on a tapered seat and is held in place by a lock nut, which means you can adjust preload (tightness) and even replace the ball stud alone if it wears out, without replacing the whole arm. The upgraded studs are also made from stronger steel and use a larger diameter, so they handle the side-loads from lifted suspension without loosening.

Common upgrade brands include Moog, Proforged, and Specialty Products Company (SPC). These parts are designed specifically for LS trucks and fit into the factory control arm holes without modification. Installation requires pressing out the old stud and pressing in the new one, which is why the job usually goes to a shop with a hydraulic press. Once installed, the upgraded joint typically lasts 100,000 to 150,000 miles even on lifted trucks, and you can adjust or rebuild it if needed instead of scrapping the whole arm.

When You Actually Need This Upgrade

If your truck is stock height and you drive on pavement, a trunnion upgrade is not urgent — the factory joint will probably last 100,000+ miles. But if you have lifted the truck 2 inches or more, tow regularly, or drive on rough terrain, the upgrade moves from optional to practical. The wear happens faster than you might expect, and a failed ball joint can leave you stranded or cause a loss of control on the highway.

You should also consider an upgrade if you are replacing the control arm anyway for another reason — ball joint replacement, tie rod work, or suspension refresh. The extra cost to upgrade at that point is $150 to $250 per side, which is much cheaper than doing it separately later. Some shops will recommend the upgrade as part of a lift kit installation, and that is usually the right call if you are spending money on suspension work anyway.

Cost and Labor Time

A trunnion upgrade costs $150 to $300 per side in parts, depending on the brand and whether you buy a complete upgraded control arm or just the stud. Labor runs $150 to $300 per side at most shops, so a full two-side job typically lands between $600 and $1,200 installed. Some shops bundle this with other suspension work and may offer a discount if you are doing multiple repairs at once.

The job takes 2 to 4 hours per side because the technician has to remove the wheel, disconnect the tie rod and ball joint, press out the old stud, press in the new one, and reassemble everything. Alignment is usually needed afterward, which adds another $100 to $200. If you are having other suspension work done at the same time — like replacing shocks or control arms — the total time and cost may not increase much because some steps overlap.

Signs Your Upper Ball Joint Is Wearing Out

A worn upper ball joint usually announces itself before it fails completely. You may notice a clunking or popping noise when you hit bumps or turn the wheel hard, especially at low speeds. The steering may feel vague or loose, as if the wheel is not responding when ready to your input. You might also see uneven tire wear on the inside edge of the front tires, because the worn joint allows the wheel to toe inward slightly.

If you grab the top of the tire and try to rock it side to side while the truck is parked, a worn ball joint will let the wheel move more than it should. A small amount of play is normal, but if you can see the wheel move noticeably, the joint is ready to be replaced. Do not ignore these signs — a completely failed ball joint can cause the wheel to collapse inward during a hard turn or bump, which can cause loss of control.

Trunnion Upgrade vs. Replacing the Whole Control Arm

When a factory ball joint wears out, you have two paths: replace just the stud with an upgraded trunnion, or replace the entire control arm. If the control arm itself is bent, cracked, or severely worn, you have to replace the whole thing anyway — the trunnion upgrade only works if the arm is still straight and sound. But if the arm is fine and only the ball joint is worn, the trunnion upgrade is the better choice because it costs less and gives you a rebuildable joint for the future.

Some shops will try to sell you a complete new control arm because it is faster and they do not have to deal with pressing studs. Push back on that if the arm is not damaged. A trunnion upgrade on a good arm costs $300 to $600 per side installed, while a new control arm runs $400 to $800 per side. Over the life of the truck, the upgraded joint saves you money and gives you more options if wear happens again.

Frequently Asked Questions

Do I need a trunnion upgrade if I have a stock truck?

Not unless the ball joint is already worn. Stock suspension on pavement roads will usually get 100,000+ miles from the factory joint. If you have lifted the truck, tow regularly, or drive rough terrain, an upgrade becomes practical because the factory joint wears faster under those conditions.

Can I install a trunnion upgrade myself?

Not without a hydraulic press. The old stud has to be pressed out of the control arm and the new one pressed in, which requires equipment most home garages do not have. A shop with a press can do it in 2 to 4 hours per side.

Will a trunnion upgrade improve my truck's handling?

It will restore handling if the factory joint was worn and loose. A tight, new ball joint removes vagueness from the steering and makes the truck feel more responsive. On a truck with a worn joint, the improvement is noticeable.

How long does a trunnion upgrade last?

On a lifted truck with normal driving, 100,000 to 150,000 miles is typical. The threaded design lasts longer than the pressed factory joint and can be adjusted or rebuilt if it wears, so you do not have to replace it as often.

What happens if I ignore a worn ball joint?

The joint will eventually fail completely, which can cause the wheel to collapse inward during a turn or bump. This creates a sudden loss of control and can cause a crash. A worn joint also accelerates tire wear and makes the truck unsafe to drive at highway speeds.