Monroe Complete Struts replace your entire strut assembly in one piece
Monroe Complete Struts are pre-assembled suspension units that replace your car's worn strut in one go, rather than rebuilding the old one. They come as a single cartridge with the shock absorber, spring, and mounting hardware already installed and tested. You unbolt the old strut and bolt in the new one — no separate spring compressor, no disassembly of parts, no guesswork about whether the spring is seated correctly.
Monroe is a suspension brand owned by Tenneco, one of the largest aftermarket suspension manufacturers in North America. Their Complete Strut line is sold through auto parts stores, tire shops, and independent mechanics. The appeal is speed and consistency: a technician can swap one in about an hour per side, versus two to three hours for a traditional rebuild.
The trade-off is cost. A complete strut costs more upfront than a strut cartridge alone, but you avoid the labour time and the risk of reassembly mistakes. For many drivers, that's worth it.
Key Takeaways
- Monroe Complete Struts arrive fully assembled with the shock, spring, and hardware ready to install, cutting labour time compared to traditional strut rebuilds.
- They fit specific vehicle models and years, so you must confirm your car's year, make, and model before ordering to avoid buying the wrong part.
- Installation typically takes one to two hours per side at a shop, though some drivers with mechanical experience handle it themselves.
- Monroe Complete Struts are a middle option between cheap cartridge-only replacements and premium strut assemblies from OEM (original equipment manufacturer) suppliers.
How Monroe Complete Struts differ from other strut options
When your strut fails, you have three main paths: replace just the cartridge (the shock part), buy a complete strut assembly, or rebuild the old one. Monroe Complete Struts sit in the middle.
A cartridge-only replacement is the cheapest option. You keep your old spring, housing, and mounts and swap out just the internal shock. This works if the spring and housing are still good, but if the spring is weak or the housing is damaged, you'll need more work later. Cartridge replacement also requires a spring compressor and careful reassembly — a mistake here can be dangerous.
An OEM complete strut from your car's manufacturer is the most expensive option and usually the most durable. It's what the factory installed originally. Monroe Complete Struts cost less than OEM but more than a cartridge alone, and they're designed to match the original ride and handling closely enough for most drivers.
A rebuild of your existing strut is possible but rare now. A shop disassembles your strut, replaces the cartridge, and reassembles it. This is labour-intensive and offers no real advantage over buying a new complete strut.
What's included in a Monroe Complete Strut
A Monroe Complete Strut arrives as one unit ready to bolt on. Inside the box you get the shock absorber cartridge, the coil spring, the strut housing, the top mount (the bearing plate that connects to your car's body), and all fasteners and bushings needed for installation.
Monroe tests each complete strut before shipping to catch leaks or defects. The spring is pre-compressed and seated in the housing, so there's no risk of the spring popping out during installation or the coils misaligning. The top mount is usually a sealed bearing that allows smooth steering wheel rotation without binding.
Some Monroe Complete Struts come with a protective dust cover over the rod to keep dirt out during shipping and storage. Check your box before installation to make sure nothing arrived damaged or missing — fasteners sometimes come loose in transit.
Installation: what to expect at a shop or doing it yourself
At a professional shop, installation of one Monroe Complete Strut typically takes 45 minutes to two hours, depending on how corroded the old bolts are and whether the car needs an alignment afterward. The technician removes the wheel, unbolts the old strut at the top (where it meets the car body) and bottom (where it connects to the steering knuckle), and slides the new one in. Then they torque the bolts to the correct specification — usually between 50 and 100 foot-pounds depending on your vehicle.
Most shops recommend replacing struts in pairs (both front or both rear) even if only one is obviously worn. A single new strut paired with an old one can cause uneven handling and uneven tyre wear. Labour for both sides is usually not double, since the shop has the car up once.
If you're mechanically inclined, you can install Monroe Complete Struts yourself with basic tools: a socket set, a jack, jack stands, and a torque wrench. You do not need a spring compressor because the spring is already installed. The hardest part is usually breaking loose the corroded bolts at the top of the strut. Many DIY installers rent a lift or work in a shop bay to make the job safer and easier. After installation, most cars need a wheel alignment to restore proper tyre wear and steering feel.
Cost and where to buy Monroe Complete Struts
Monroe Complete Strut prices vary by vehicle model and year. A single strut for a common sedan typically ranges from $150 to $400, while trucks and SUVs can run higher. A pair (both front or both rear) usually costs $300 to $800 before installation labour.
You can buy Monroe Complete Struts from national auto parts chains like AutoZone, O'Reilly Auto Parts, NAPA, and Advance Auto Parts. Many tire shops and independent mechanics stock them or can order them overnight. Some online retailers ship them, but shipping costs can be high because struts are bulky and heavy.
Before you buy, confirm your vehicle's year, make, model, and engine size — some cars have multiple strut options. Write down the information from your registration or owner's manual and bring it to the parts counter or provide it online. Ordering the wrong strut is a common mistake and wastes time and money.
Signs your struts need replacement
Worn struts usually announce themselves through handling and noise. Your car may bounce excessively after hitting a bump, take longer to stop, or feel unstable on curves. You might hear clunking or creaking from the suspension, especially over rough roads. The front end may dip noticeably when you brake, or the rear may sag lower than it used to.
Uneven tyre wear — especially wear on the outer edges of the front tyres — is often a sign of worn struts. So is a steering wheel that feels loose or vague. If you notice any of these, have a mechanic inspect the struts. They can push down on each corner of the car and watch how many times it bounces after you release it — more than one or two bounces suggests worn struts.
Struts typically last 50,000 to 100,000 miles, though this varies by driving conditions, road quality, and how heavily you load your car. Rough roads, potholes, and frequent towing wear them out faster.
Warranty and reliability of Monroe Complete Struts
Monroe typically backs Complete Struts with a limited warranty of one to three years, depending on the product line and where you buy. The warranty usually covers defects in materials and workmanship — leaks, broken springs, or failed seals — but not wear from normal use or damage from accidents or road hazards.
Monroe is a well-established brand with decades of history in the aftermarket suspension market. Complete Struts are generally considered reliable and a good value compared to OEM struts. They're not premium performance parts, but they're engineered to restore the original ride and handling of your car reasonably well.
Keep your receipt and warranty paperwork. If a strut fails early, contact the shop where it was installed or the parts retailer where you bought it. They can help you file a warranty claim with Monroe.
Frequently Asked Questions
Do I have to replace both struts at the same time?
You don't have to, but most mechanics recommend it. A new strut paired with an old, worn one creates uneven suspension stiffness, which can cause uneven tyre wear and handling problems. If only one strut is obviously leaking or broken, the other is usually close behind. Replacing both at once costs more upfront but saves money and hassle later.
Can I install Monroe Complete Struts myself without special tools?
Yes, if you have basic mechanical skills and the right tools: a socket set, jack, jack stands, and a torque wrench. You don't need a spring compressor because the spring is pre-installed. The trickiest part is usually removing the old corroded bolts. After installation, take the car to a shop for a wheel alignment, which you should not do yourself.
How long does a Monroe Complete Strut last?
Monroe Complete Struts typically last 50,000 to 100,000 miles, the same as OEM struts. Lifespan depends on road conditions, driving habits, and how much weight you carry. Rough roads and potholes wear them out faster. If you notice bouncing, clunking, or uneven tyre wear before 50,000 miles, have them inspected.
What's the difference between Monroe Complete Struts and Monroe Reflex struts?
Monroe Reflex is a different product line designed for a smoother, more comfortable ride on rough roads. Complete Struts are the standard line and restore the original ride feel. Both are pre-assembled, but Reflex struts use different tuning. Ask your parts supplier which line is recommended for your vehicle and driving style.
Do I need an alignment after installing Monroe Complete Struts?
Yes, a wheel alignment is strongly recommended after strut replacement. New struts restore suspension geometry, but the alignment may have drifted while the old struts were worn. An alignment ensures even tyre wear and proper steering feel. Most shops include alignment in the total labour cost or offer it as an add-on for $75 to $200.