Reklez suspension explained
Reklez suspension is a brand name for an independent double-wishbone suspension system designed primarily for off-road and performance vehicles. The system uses two A-shaped control arms (the wishbones) per wheel to manage vertical wheel movement while keeping the wheel aligned during compression and extension. Reklez suspensions are known for their adjustability and ability to handle rough terrain without losing stability on paved roads.
The core purpose of any double-wishbone setup is to keep your tire contact patch flat against the ground as the suspension compresses and extends. Reklez achieves this through precise geometry and, in many cases, coil-over dampers that let you adjust ride height and spring stiffness independently. This matters because a wheel that tilts or loses contact during a bump transfers less power to the ground and wears the tire unevenly.
Reklez suspensions appear most often on mid-size trucks, SUVs, and rock-crawling vehicles where owners want both highway comfort and serious off-road capability. The brand competes with other performance suspension makers like Fox, King, and Bilstein, though Reklez systems tend to emphasize adjustability over bolt-on simplicity.
Key Takeaways
- Reklez suspension uses two control arms per wheel to maintain tire contact and wheel alignment during compression, which improves both off-road traction and on-road handling.
- Most Reklez systems are coil-over designs, meaning you can adjust ride height and spring rate separately without replacing major components.
- Installation typically requires removing the factory suspension entirely and may need frame modifications or new mounting points on some vehicles.
- Reklez suspensions cost significantly more than factory systems but less than some competing performance brands, with total installed cost varying by vehicle and setup.
How the double-wishbone design works
Each wheel on a Reklez suspension connects to the frame through two control arms that form an A or wishbone shape when viewed from the side. The upper arm is shorter than the lower arm. As the wheel moves up and down, both arms pivot at the frame end, and the wheel pivots at the outer end where both arms meet. This geometry keeps the wheel more upright and maintains a consistent distance from the frame as the suspension cycles.
The angle at which the wheel sits relative to the ground is called camber. A double-wishbone layout naturally resists camber change during suspension movement — meaning your tire stays flatter on the ground during bumps and body roll. This is why performance and off-road vehicles use this design: it keeps traction consistent whether you are on pavement, gravel, or rocks.
Reklez systems pair this geometry with coil-over dampers — a spring and shock absorber combined into one unit. You can adjust the spring's preload (how much it is compressed at rest) to change ride height, and you can often adjust damping (how fast the shock compresses and extends) to tune how the vehicle feels over different terrain. This modularity is a selling point: you can dial in the setup for your specific use without buying a whole new suspension.
Installation and what it involves
Installing a Reklez suspension is not a bolt-on job. The system replaces your factory suspension entirely, which means removing the factory control arms, springs, shocks, and often the factory sway bars. On many vehicles, the frame mounting points are in different locations than factory, so new brackets or reinforcement may be needed.
The installation process typically takes a shop 16 to 24 hours depending on the vehicle and how much fabrication is required. You will need a full alignment afterward because changing suspension geometry changes how your wheels sit relative to the frame. Some vehicles also need modifications to brake lines, wiring for electronic components, or clearance work to prevent rubbing.
Labor costs vary widely by region and shop, but expect to pay $1,500 to $3,000 for installation alone on top of the Reklez kit itself. Some shops that specialize in off-road builds charge more; others may charge less. Get a quote from a shop familiar with your specific vehicle before committing, because unexpected frame damage or missing mounting points can add time and cost.
Reklez versus factory suspension trade-offs
Factory suspensions prioritize cost, durability for normal driving, and a smooth highway ride. They use simpler geometry and fixed spring rates because they have to work for millions of vehicles with different weights and driving styles. Reklez suspensions sacrifice some of that one-size-fits-all simplicity to give you adjustability and better performance in specific conditions.
On pavement, a well-tuned Reklez suspension can feel sharper and more responsive than factory, with less body roll in corners. Off-road, the improved wheel articulation and adjustable damping let you maintain traction over obstacles that would unload a factory suspension. The trade-off is complexity: more adjustments mean more ways to get the tuning wrong, and more components mean more potential failure points if you do not maintain them.
Reklez suspensions also sit higher than factory on most vehicles, which raises your center of gravity slightly. This can make the vehicle feel less stable in emergency maneuvers on pavement, though the improved wheel control often compensates. If you spend 80 percent of your time on highways and 20 percent off-road, a Reklez system may feel like overkill; if you split your time more evenly or lean heavily off-road, the investment makes more sense.
Maintenance and long-term durability
Reklez coil-over dampers need periodic maintenance that factory shocks do not. The damping fluid inside can break down over time, especially if you run the suspension hard in dusty or wet conditions. Most manufacturers recommend servicing or replacing dampers every 50,000 to 100,000 miles depending on use. A full damper rebuild or replacement costs $300 to $800 per corner.
The control arms themselves are typically stronger than factory arms because they are designed for higher loads and more extreme movement. However, they still wear out. Ball joints and bushings can develop play after heavy use, which shows up as clunking noises or loose steering feel. Replacing a control arm assembly costs $200 to $500 per side depending on the part and labor.
Reklez suspensions also expose more of the undercarriage to rocks and debris than factory systems, so skid plates and protective guards are common add-ons. Regular inspection of all suspension components — especially after off-road trips — catches wear early and prevents catastrophic failure on the trail.
Cost comparison with other performance suspension brands
A complete Reklez suspension kit for a mid-size truck typically costs $2,500 to $4,500 before installation. This puts it in the middle of the performance suspension market. Fox suspensions tend to cost more ($4,000 to $6,000 for a comparable kit), while some budget performance brands cost less ($1,500 to $2,500). King suspensions, another popular choice, usually fall in the $3,500 to $5,500 range.
The total installed cost — kit plus labor plus alignment — usually lands between $5,000 and $8,000 for Reklez. This is a significant investment, but it is less than a full Fox build and more than a basic coil-over upgrade. Your actual cost depends on your vehicle, how much fabrication the shop needs to do, and whether you need additional components like sway bars or skid plates.
When comparing brands, look at what is included in the kit: dampers, control arms, bushings, and brackets all vary. Some kits come with adjustable sway bars; others do not. Some include bump stops and droop limiters; others sell them separately. Get a full parts list and installed price from the shop before deciding, because the cheapest kit is not always the best value if it requires more add-ons later.
Frequently Asked Questions
Can I install a Reklez suspension myself?
If you have suspension experience and a full shop setup, you can do it, but most owners take it to a shop. The work requires lifting the vehicle safely, removing and installing multiple bolted connections, and getting an alignment afterward. A mistake during installation can affect handling and safety. Budget for professional labor unless you have done this type of work before.
Will a Reklez suspension void my vehicle's warranty?
Yes, in most cases. Replacing the suspension is a major modification that manufacturers consider outside their warranty scope. Some dealers may still cover unrelated warranty items, but suspension-related failures will not be covered. Check your vehicle's warranty terms and talk to your dealer before installation if warranty coverage matters to you.
Do I need new tires after installing Reklez suspension?
Not necessarily, but the change in ride height and geometry may expose tire wear patterns your old tires already have. A full alignment after installation will help, but if your tires are already worn, replacing them at the same time makes sense. New tires also let you choose a compound and tread pattern that matches your new suspension's capabilities.
How much does ride height change with Reklez suspension?
Most Reklez systems raise the vehicle 1 to 3 inches depending on the kit and how you adjust the coil-overs. The exact amount varies by vehicle and your spring preload settings. Talk to your shop about the expected height change for your specific vehicle, because it affects ground clearance, approach angles, and how the vehicle looks.
Can I adjust Reklez suspension myself after installation?
Yes, you can adjust preload and damping settings yourself with basic tools, but getting the tuning right takes experience. Small adjustments to spring preload change ride height; adjusting damping changes how the suspension feels over bumps. Most owners make one or two adjustments and then leave it alone, or they work with their shop to dial it in for their specific use.