What Hendrickson suspension does

Hendrickson is a manufacturer of suspension systems for heavy-duty trucks, primarily trailers and commercial vehicles. Their suspensions connect the axles to the frame and absorb the shock and movement from the road. The most common Hendrickson systems you'll encounter are air suspensions—they use pressurized air in rubber bellows instead of steel springs to support the vehicle's weight and smooth out bumps.

If you own or operate a commercial truck or trailer, you likely have a Hendrickson suspension underneath. They make systems for single-axle and tandem-axle configurations, and they're built to handle repeated heavy loads over long distances. The suspension's job is to keep the wheels in contact with the road, protect your cargo from damage, and keep the cab stable so the driver isn't thrown around.

Understanding how your Hendrickson suspension works matters because problems with it affect how your truck handles, how much it costs to repair, and whether it's safe to drive. A failing suspension can damage cargo, wear out tires faster, and eventually leave you stranded.

Key Takeaways

  • Hendrickson air suspensions use pressurized air in bellows to support weight and absorb road shock, which is gentler on cargo and the frame than steel springs.
  • Air suspensions can be manually leveled or automatically self-leveling, depending on the model and year of your truck.
  • Common problems include air leaks, worn air springs, failed compressors, and broken shock absorbers—all of which affect handling and safety.
  • Regular inspection of air lines, bellows, and shock absorbers can catch problems before they cause damage or leave you stranded.
  • Repair costs vary widely depending on what fails, but air spring replacement and compressor repair are among the most common expenses.

How air suspension differs from steel spring suspension

A steel spring suspension uses coiled or leaf springs to support the truck's weight and absorb bumps. An air suspension replaces those springs with air-filled rubber bellows called air springs or air bags. When you load the truck, the air inside compresses, and when you hit a bump, the air absorbs the shock before it reaches the frame.

The advantage is ride quality and cargo protection. Air suspensions keep the truck at a more consistent height regardless of load, which means your cargo sits at the same angle whether you're empty or fully loaded. Steel springs sag under weight, which can tilt the load and put stress on tie-downs. Air suspensions also isolate vibration better, so delicate freight arrives in better condition and the driver experiences less fatigue.

The trade-off is complexity. An air suspension needs a compressor to pressurize the system, air lines to carry that pressure, and valves and sensors to manage it. If any of those components fail, the suspension stops working. A steel spring can fail too, but it's a simpler system with fewer parts to break.

Main components of a Hendrickson air suspension

A Hendrickson air suspension has several parts that work together. The air compressor is driven by the engine and pressurizes air into a storage tank. From there, air travels through lines to the air springs (the rubber bellows under each axle) and through a leveling valve that controls how much air goes into each spring based on the load.

Shock absorbers dampen the bouncing motion after the air springs absorb a bump—without them, the truck would bounce up and down for several seconds after hitting a pothole. Brake chambers on each wheel use air pressure to explore the brakes. A pressure relief valve prevents the system from over-pressurizing, and air dryers remove moisture from the air so it doesn't corrode the lines and valves from the inside.

On newer Hendrickson systems, electronic sensors monitor air pressure and suspension height and can automatically adjust the system or alert the driver to a problem. Older systems are purely mechanical and rely on the driver to notice changes in how the truck handles.

Common problems and what causes them

Air leaks are the most frequent issue. They can occur in the air springs themselves (the rubber deteriorates over time), in the lines (corrosion or damage), or at connection points. A slow leak might take days to empty the system; a fast leak can flatten the suspension in hours. You'll notice the truck sitting lower than usual or listing to one side.

Compressor failure means the system can't pressurize air, so the suspension won't work at all. The compressor can fail because of age, because moisture got into the system and corroded internal parts, or because the air dryer stopped working. A failed compressor usually means the truck won't move safely until it's replaced.

Worn shock absorbers let the truck bounce excessively after bumps. You'll feel it in the cab—the truck takes longer to settle down after hitting a pothole, and it may bounce side to side on curves. Worn shocks also put extra stress on the air springs and frame.

Leveling valve failure means the suspension can't maintain consistent height as the load changes. The truck might sit too high (wasting fuel and making it unstable) or too low (dragging the frame or cargo on the ground). Electronic leveling systems can fail if sensors get dirty or wiring corrodes.

How to inspect your Hendrickson suspension

Start with a visual inspection. Get under the truck (safely, on a lift or with proper jack stands) and look at the air springs. They should be smooth and not cracked or leaking. Feel along the air lines for soft spots, cracks, or corrosion. Check that all connections are tight and not weeping air.

Listen for air leaks when the engine is running and the compressor is pressurizing the system. A hissing sound means air is escaping somewhere. Check the shock absorbers for oil leaks (they contain fluid that dampens movement) and for damage to the rod or body.

Test the suspension's response. Drive over a bump and feel how quickly the truck settles. If it bounces more than once or twice, the shocks are worn. Check that the truck sits level when parked on flat ground. If one corner is noticeably lower, there's likely a leak in that air spring.

Have the air pressure checked with a gauge. Most Hendrickson systems run between 80 and 100 pounds per square inch (psi), but the correct pressure for your truck is listed on a placard on the frame or in the owner's manual. Pressure that's too low or too high indicates a problem.

Maintenance to prevent suspension problems

Replace the air dryer cartridge at the interval specified in your maintenance schedule—usually every 50,000 to 100,000 miles, depending on how wet the air is where you operate. A clogged or failed air dryer lets moisture into the system, which corrodes lines and valves from the inside and can eventually cause compressor failure.

Inspect air lines and connections every time you do a pre-trip inspection. Look for visible damage, corrosion, or leaks. Tighten any loose fittings. If you find a small leak at a connection, try tightening the fitting first; if that doesn't stop it, the fitting or line needs to be replaced.

Have shock absorbers inspected annually. They wear gradually, so you might not notice the change in handling until they're very worn. Replacing them before they fail prevents extra stress on the air springs and frame.

Keep the compressor clean and check its oil level if it's an oil-lubricated model. A compressor that runs out of oil will seize and fail. If the compressor cycles on and off frequently (more than every few minutes when parked), there's likely a leak somewhere in the system that needs to be found and fixed.

When to replace versus repair

Air springs typically last 5 to 10 years or 100,000 to 200,000 miles, depending on how heavily the truck is loaded and how rough the roads are. Once they start leaking, they can't be repaired—they have to be replaced. Replacing one air spring usually means replacing the pair on that axle, because if one is worn enough to leak, the other is close behind.

Shock absorbers can be replaced individually, but if one is worn, the others on the same axle are usually close to failure. Many shops recommend replacing all four at once to restore even handling.

Compressors can sometimes be rebuilt if the failure is internal wear, but replacement is more common because a rebuilt compressor may not last as long as a new one. The decision depends on the cost difference and how much life is left in the truck.

Air lines and fittings can be repaired if the damage is minor (a small crack or loose connection), but severely corroded or kinked lines should be replaced. Mixing repairs and replacements is common—you might replace the worst line and repair a fitting on another line.

Frequently Asked Questions

How do I know if my air suspension has a leak?

The truck will sit lower than usual, especially on one corner if the leak is in one air spring. You may hear a hissing sound when the engine is running. Check the air pressure with a gauge—if it's below the specification on the frame placard, there's a leak. The truck may also handle poorly or bounce excessively.

Can I drive with a failed air suspension?

No. A completely failed air suspension means the truck has no shock absorption and may not have brake pressure either, since many air brake systems depend on the same compressor. The truck is unsafe to drive and will damage cargo and the frame. Have it towed or repaired before moving it.

What does it cost to replace an air spring?

Costs vary by truck model and whether you do it yourself or have a shop do it. A single air spring cartridge costs roughly $200 to $400, but you usually replace both on an axle. Labor adds $300 to $800 depending on how difficult the job is. Total cost for replacing both air springs on one axle is typically $800 to $1,600.

Why does my truck sit lower on one side?

One air spring is leaking or has failed. The leveling valve can't maintain pressure in that spring, so that corner sags. This needs to be fixed soon—driving with uneven suspension stresses the frame and axles and makes the truck unstable, especially when turning or braking.

How often should I have my suspension inspected?

At minimum, inspect it during your annual safety inspection and whenever you notice a change in how the truck handles. If you operate in rough terrain or carry heavy loads regularly, inspect it every six months. Catching problems early prevents breakdowns and keeps repair costs lower.