You can change a car tire yourself with basic tools and about 15 minutes

Changing a tire is a skill most drivers can learn in one afternoon. You need a jack, a lug wrench, and a spare tire — all of which come standard in most vehicles. The process involves loosening the lug nuts while the car is still on the ground, raising the car with the jack, removing the old tire, installing the spare, and tightening everything back down. If you have never done this before, the hardest part is usually the physical effort of breaking the lug nuts loose, not the sequence itself.

This guide walks you through each step in order. It assumes you have a standard spare tire (not a full-size spare, which works the same way but is heavier). If your car has a tire repair kit or a run-flat tire instead, the steps differ — check your owner's manual for those systems.

Key Takeaways

  • Loosen the lug nuts while the tire is still on the ground, because the wheel will spin if you try to loosen them after the car is raised.
  • Raise the car with the jack positioned under the frame near the wheel you are changing, not under the bumper or plastic trim.
  • Remove the old tire completely before installing the spare, and hand-tighten the lug nuts first so you do not cross-thread them.
  • Tighten the lug nuts in a star or cross pattern, not in a circle, to keep the wheel centered as you go.
  • Drive to a tire shop within a few days to have the spare inspected and the flat tire repaired or replaced.

Gather your tools and move to a safe location

Pull over to a flat, stable surface away from traffic. A parking lot or wide shoulder is better than the roadside of a busy highway. Turn on your hazard lights and engage the parking brake. If you are on a slope, turn the steering wheel away from the road so the car will not roll toward traffic if the brake fails.

Open your trunk and locate the jack, lug wrench, and spare tire. Most cars store these under the trunk floor or along the side wall. Check that the spare tire has air in it — press your thumb against it; it should be firm, not soft or flat. If the spare is flat, you will need to call for a tow or roadside information instead of changing the tire yourself.

Loosen the lug nuts before raising the car

Place the lug wrench on one of the lug nuts and turn it counterclockwise. Do not remove the nut completely yet — just loosen it enough that you can turn it by hand. Repeat this for all five lug nuts (or however many your car has; most have five). This step is critical: if you wait until the car is raised, the wheel will spin and you will not be able to loosen the nuts.

If a lug nut is stuck, explore steady pressure rather than jerking the wrench. You can also place the wrench on the nut and step on the wrench handle to use your body weight. Do not hit the wrench with a hammer or use a pipe extension on the handle — you risk stripping the nut or damaging the wrench.

Raise the car with the jack

Locate the jack point on your car — this is a reinforced spot on the frame, usually marked by a small notch or dimple. It is typically located just behind the front wheel or just in front of the rear wheel, depending on which tire you are changing. Do not place the jack under the bumper, plastic trim, or fuel tank. Check your owner's manual if you cannot find the jack point.

Position the jack directly under the jack point and raise the car until the tire is about six inches off the ground. The car should be high enough that you can remove the old tire and fit the spare on, but not so high that the car feels unstable. If the ground is soft or muddy, place a flat board under the jack base to spread the weight and prevent the jack from sinking.

Remove the old tire and install the spare

Now that the lug nuts are loosened and the car is raised, finish unscrewing them by hand and set them aside in a safe place where you will not lose them — a cup or small container works well. Remove the old tire by pulling it straight toward you. It may be stuck; if so, rock it gently side to side or tap the rim with the heel of your hand to break it free.

Lift the spare tire and align the holes with the lug bolt studs on the wheel hub. Push the spare onto the studs until it sits flush against the hub. Hand-tighten each lug nut onto its stud. This prevents you from cross-threading them (screwing them on at an angle), which would damage the studs and make the wheel unsafe. Once all five nuts are hand-tight, you can use the wrench to tighten them further.

Tighten the lug nuts in a star pattern

Use the lug wrench to tighten the lug nuts, but do not tighten them in order around the wheel. Instead, tighten them in a star or cross pattern: if you imagine the lug nuts as the points of a star, tighten the top one, then the bottom one, then the left one, then the right one, then the remaining one. This distributes pressure evenly and keeps the wheel centered on the hub as you tighten.

Tighten each nut firmly, but do not over-tighten. You want them snug enough that the wheel will not come loose, but not so tight that you strip the studs or make it impossible to remove the nuts later. If you have a torque wrench, your owner's manual will specify the correct tightness in foot-pounds; most passenger cars use 80 to 100 foot-pounds. If you do not have a torque wrench, tighten until you feel solid resistance and cannot turn the wrench further with moderate force.

Lower the car and do a final check

Slowly lower the car by turning the jack handle counterclockwise. Lower it until the spare tire is fully supporting the car's weight and the jack is no longer under the car. Remove the jack and set it aside.

Give each lug nut one more quarter-turn with the wrench to confirm they are tight. Visually inspect the spare tire to make sure it is seated evenly against the hub and the lug nuts are all in place. Put the old tire, jack, and lug wrench back in your trunk. Turn off your hazard lights and drive slowly to a tire shop — do not drive faster than 50 miles per hour on a spare tire.

Have the flat tire repaired or replaced within a few days

Spare tires are temporary. They are smaller, lighter, and designed to get you to a shop, not to be driven long-term. Most spare tires are rated for 50 miles per hour and should not be driven more than 70 miles. Visit a tire shop as soon as you can to have the flat tire repaired (if the damage is minor) or replaced (if it cannot be repaired).

When you have the flat repaired or replaced, ask the shop to reinstall it on your car and move the spare back to your trunk. They can also use a torque wrench to tighten the lug nuts to the correct specification, which is more precise than hand-tightening.

Frequently Asked Questions

What if I cannot loosen the lug nuts by hand?

Lug nuts can seize if they have been on the wheel for years. Try spraying penetrating oil (like WD-40) on the nuts and waiting 10 minutes before trying again. If they still will not budge, do not force it — call roadside information. Stripping a lug nut or stud is expensive to repair.

Can I change a tire if my car is parked on a hill?

It is not safe. The car can roll even with the parking brake on, especially if the ground is wet or icy. If you must change a tire on a slope, place wheel chocks (or rocks, or pieces of wood) behind the wheels to prevent rolling, and turn the steering wheel away from the road.

What if the spare tire is flat when I need it?

You will need to call for roadside information or a tow truck. Some insurance policies and roadside membership plans (like AAA) cover this. If you do not have coverage, you can call a local tire shop and ask if they offer mobile service or can recommend a towing company.

Do I need to balance or align the wheel after changing a tire?

A spare tire does not need balancing or alignment right away — it is meant to be temporary. When you have the flat tire repaired and reinstalled, the shop will balance it as part of the repair. If you notice vibration or pulling to one side while driving on the spare, have it checked at a shop before continuing.

How tight should the lug nuts be?

Most passenger cars require 80 to 100 foot-pounds of torque. Check your owner's manual for the exact specification for your vehicle. If you do not have a torque wrench, tighten the nuts firmly until you feel solid resistance, then have them checked at a tire shop within a few days to make sure they are correct.