What happens when you change a tire yourself

Changing a tire means removing the wheel with the flat or damaged tire and putting on a spare in its place. You do this by loosening the lug nuts (the bolts that hold the wheel on), lifting the car with a jack, taking off the old wheel, sliding the spare onto the wheel bolts, and tightening everything back down. The whole job takes 15 to 30 minutes if you have never done it before, and much less once you know the steps.

You need four things to do this: a spare tire (which comes with most cars), a jack (usually in your trunk), a lug nut wrench (often a cross-shaped tool that fits your car's lug nuts), and a flat, stable surface to work on. A parking lot or shoulder is fine; a slope or soft ground is not. The real risk is not the work itself — it is doing it on the side of a busy road or in the dark without being seen.

Key Takeaways

  • Loosen the lug nuts while the car is still on the ground, because the wheel will spin if you try to loosen them after you lift the car.
  • Park on a flat, stable surface away from traffic, turn on your hazard lights, and engage the parking brake before you start.
  • The jack goes under the frame of the car near the wheel you are changing — never under the plastic bumper or body panel.
  • Tighten the lug nuts in a star or cross pattern (opposite sides, not in a circle) so the wheel sits evenly on the hub.
  • After you drive away, stop after a few miles and check that the lug nuts are still tight, because they can loosen as the wheel settles.

Before you lift the car: loosen the lug nuts on the ground

The first step is to loosen the lug nuts while the car's full weight is on the wheel. If you loosen them after you lift the car, the wheel will spin and you will not be able to turn the nuts. Put your lug nut wrench on each nut and turn it counterclockwise. You do not need to remove the nuts all the way — just break them loose so they turn freely. This is the hardest part of the job because the nuts are tight from the factory and from the weight of the car.

If a nut will not budge, do not force it. Stop, let the wrench sit on the nut for a minute (sometimes the pressure helps), and try again with steady pressure rather than jerking. If it still will not move, you may need to call for roadside help rather than risk stripping the nut or breaking the wrench. Once all four nuts are loose, you can move to the next step.

Position the car safely and lift it with the jack

Move your car to a flat, stable surface away from traffic if you can. Turn on your hazard lights so other drivers see you. Engage the parking brake firmly. If you have wheel chocks (wedges that go behind the wheels), put them behind the wheels that are staying on the ground — this prevents the car from rolling. If you do not have chocks, a heavy rock or brick works.

Find the jacking point on your car. This is a reinforced spot on the frame, usually marked by a small notch or raised area near the wheel. Your owner's manual shows exactly where it is. The jack goes under this point, never under the plastic bumper, body panel, or fuel tank. Position the jack so it is perpendicular to the ground, then pump or turn the handle to lift the car until the wheel is about six inches off the ground. You should be able to fit your hand under the tire.

Remove the old wheel and install the spare

Now finish unscrewing the lug nuts by hand and set them somewhere you will not lose them — a cup or small container works well. Pull the wheel straight toward you to remove it. It may be stuck; if so, rock it gently side to side or tap the back of the tire with your foot. Once it is off, set it flat on the ground so it does not roll away.

Pick up the spare tire and line up the holes in the center with the bolts sticking out from the hub. Slide the spare onto the bolts and push it all the way in until it sits flush against the hub. Put the lug nuts back on by hand and turn them clockwise until they are snug. Do not use the wrench yet — hand-tight is enough for now.

Tighten the lug nuts in the correct pattern

Use the lug nut wrench to tighten the nuts, but not in a circle. Instead, tighten them in a star or cross pattern: if the wheel has five lug nuts, tighten the top one, then the bottom-left one, then the top-right one, then the bottom-right one, then the remaining one. If the wheel has four lug nuts, tighten the top one, then the bottom one, then the left one, then the right one. This pattern pulls the wheel evenly onto the hub.

Tighten each nut firmly but do not overtighten — you want them snug, not stripped. A good rule is to tighten until you feel solid resistance, then give the wrench a quarter turn more. Once all the nuts are tight in the star pattern, lower the car by turning the jack handle in the opposite direction until the tire touches the ground and the car's full weight is on the wheel.

Lower the car and do a final check

Once the car is fully on the ground, use the wrench to tighten the lug nuts one more time in the same star pattern. This catches any that may have loosened slightly as the wheel settled. After this final tightening, you are done. Put the flat tire, jack, and wrench back in your trunk.

Drive slowly to a tire repair shop as soon as you can. A spare tire is temporary — it is smaller than a regular tire, and your car may not handle the same way. Some spares are designed for short distances only. Your owner's manual tells you the speed limit and distance limit for your spare. Once you reach the shop, the technician can repair the flat tire or replace it if it cannot be fixed.

What to do if you get stuck during the change

If a lug nut is seized and will not loosen, or if the wheel is stuck and will not come off, stop and call roadside help. Forcing these things can break the wrench, strip the nut, or damage the wheel. If you do not have roadside coverage, many tire shops and auto clubs offer emergency tire change service for a fee. It is worth the cost rather than risk being stranded or injured.

If you lift the car and the jack starts to slip or the car feels unstable, lower it when ready and reposition the jack. Never work under a car that is only supported by a jack — the jack can fail. If you are not confident the car is stable, call for help. Your safety is more important than changing the tire yourself.

Frequently Asked Questions

Do I need to replace the lug nuts when I change a tire?

No, the same lug nuts go back on. They are reusable unless they are damaged, stripped, or corroded so badly they will not turn. If a nut is stuck or damaged, the tire shop can replace it when you bring in the flat tire.

What if my car does not have a spare tire?

Some newer cars come with a tire repair kit or run-flat tires instead of a spare. Check your trunk and your owner's manual. If you have a repair kit, follow the instructions in the kit. If you have run-flat tires, you can drive on them after a puncture, but you must go to a tire shop right away — they are designed for temporary driving only.

Can I change a tire in the rain or at night?

You can, but it is harder and more dangerous. In the rain, the ground is slippery and the wrench may slip. At night, you cannot see what you are doing. If possible, wait for better conditions or call roadside help. If you must change the tire in the dark, use your phone's flashlight or a headlamp so you can see the lug nuts and the jacking point.

How tight should the lug nuts be?

Tight enough that they do not come loose, but not so tight that you strip the threads or cannot remove them next time. Tighten until you feel solid resistance, then give the wrench a quarter turn more. After you drive a few miles, stop and check them again — they often loosen slightly as the wheel settles.

What if the spare tire is flat?

Check the spare before you need it. Every few months, look at it and make sure it has air in it. If the spare is flat when you need it, you cannot use it. Call roadside help or a tow truck to take you to a tire shop. This is why it is worth checking your spare regularly — a flat spare is useless in an emergency.