What you need before you start
Changing a bike tube takes a tire lever, a new tube sized to match your rim, and a pump. You do not need special tools or a repair stand, though a stand makes the work easier. The whole job takes 15 to 20 minutes once you have done it once.
Before you begin, identify your tire size. Look on the sidewall of your tire — you will see a number like 700x28c (road bike) or 26x2.1 (mountain bike). Buy a replacement tube marked for that size. Tubes are cheap and come in a cardboard box at any bike shop or big-box retailer. Bring your old tube with you if you are unsure of the size.
A tire lever is a flat plastic or metal tool that hooks under the tire bead (the edge that sits on the rim). Most bikes come with one or two in the seat bag. If you do not have one, buy a plastic lever for a few dollars — metal ones can dent your rim if you slip.
Key Takeaways
- Remove the wheel by opening the quick-release lever or unscrewing the axle nuts, then use a tire lever to pry one side of the tire off the rim.
- Pull out the old tube completely, then inspect the inside of the tire for thorns, glass, or sharp objects that caused the puncture.
- Insert the new tube by first inflating it slightly so it holds its shape, then seating it evenly in the tire before reinstalling the tire bead.
- Pump the tire to the pressure marked on the sidewall, then reinstall the wheel and check that it spins freely without rubbing the frame.
Remove the wheel from the frame
On a road bike or hybrid, open the quick-release lever on the axle by flipping it outward. On a mountain bike or older bike, use a wrench to unscrew the axle nuts on both sides. For the rear wheel, shift to the smallest cog first, then pull the derailleur back to create slack in the chain.
Lift the wheel out of the frame. If the tire is flat, it will be easier to maneuver. Set the wheel on a clean surface where you can work without the tire rolling away.
Pry the tire off the rim
Insert a tire lever under the tire bead (the edge of the tire that sits on the rim) about 6 inches from the valve. Pry gently until the tire lip comes up and over the rim edge. You do not need to force it — if it resists, you may be in the wrong spot or the tire may be very tight.
Once the first section is loose, slide the lever around the rim to free one full side of the tire. You only need to remove one side; the other side stays seated on the rim. If you have two levers, hook the second one to the rim to hold the first side in place while you work.
Remove the old tube and check the tire
Pull the valve stem out of the rim hole first, then slide the old tube out from under the tire. Set it aside — you may want to inspect it later to see where the puncture was, though you do not need to repair it.
Run your fingers slowly around the inside of the tire, feeling for thorns, glass shards, or sharp objects. This is the most important step: if you do not remove what caused the first puncture, your new tube will fail in the same spot. If you find something, remove it and mark the spot on the outside of the tire with a pen so you can inspect that area later.
Install the new tube
Inflate the new tube slightly — just enough so it holds its shape and is not completely flat. This makes it much easier to seat evenly in the tire without twisting or pinching. You are aiming for maybe 20 to 30 percent of final pressure; the tube should still be soft to the touch.
Insert the valve stem through the rim hole first. Then tuck the tube under the tire all the way around, working your way around the wheel. Make sure the tube is not twisted and sits evenly — if one section is bunched up, the tire will not seat properly and may pinch the tube when you inflate it.
Starting opposite the valve, use your hands to push the tire bead back onto the rim. Work your way around in both directions toward the valve. The last section near the valve will be tight; push the valve up into the rim to create slack, then roll the final section of tire onto the rim. You should be able to do this by hand without a lever.
Inflate and reinstall the wheel
Pump the tire to the pressure marked on the sidewall. Road tires typically call for 80 to 130 psi; mountain tires for 30 to 50 psi. Start at a lower pressure and work up, checking that the tire bead is seating evenly on both sides of the rim as you go. If the bead is not seated, you will see a gap between the tire and rim.
Once the tire is at full pressure, reinstall the wheel in the frame. Tighten the quick-release or axle nuts firmly — the wheel should not move side to side. Spin the wheel to make sure it does not rub on the brake pads or frame. If it does, the wheel may not be centered; remove it and reseat it in the frame.
What to do if the tube keeps failing
If you get a second puncture in the same location, the cause is still in the tire. Repeat the inspection step more carefully, running your fingers slowly and feeling for anything sharp. Sometimes a thorn is embedded so deeply that your finger will not catch it; look for a tiny hole or discoloration on the inside of the tire.
If you find nothing but the punctures keep happening in the same spot, the tire itself may be damaged. A small cut or hole in the casing can allow the tube to bulge through and puncture. In that case, replace the tire rather than the tube — a new tire costs more but will solve the problem permanently.
Frequently Asked Questions
Do I have to remove the wheel to change the tube?
No. You can change the tube with the wheel still on the frame if you have room to work. Removing the wheel makes it easier to inspect the tire and seat the new tube evenly, so most people do it. On a rear wheel with a derailleur, removing the wheel is usually faster than working around the chain.
What if I pinch the new tube while reinstalling the tire?
If you hear a hiss or see the tube bulging out from under the tire, stop and deflate completely. Remove the tire bead again, reposition the tube so it is not twisted, and try again. Pinches usually happen because the tube is not seated evenly or because you inflated too fast. Go slower the second time.
Can I patch a tube instead of replacing it?
Yes, if the puncture is small and you have a patch kit. Patches work well for thorns or small holes. If the puncture is large, the valve is damaged, or the tube is old and cracked, replacement is faster and more reliable. Most riders carry a spare tube and patch the old one at home later.
How do I know if my tire is too old to reuse?
Check the sidewall for cracks, dry rot, or hardening. If the rubber is cracked or feels brittle, replace the tire. If it looks fine and holds air, it is safe to use. Age alone does not make a tire unsafe — condition does. A well-maintained tire can last several years.