What you need before you start

Replacing a tire requires four things: a spare tire (full-size or temporary), a jack, a lug wrench, and a flat surface away from traffic. Check your owner's manual or the inside of your driver's door jamb for the correct jack type and weight capacity for your vehicle. Most cars come with these tools in the trunk, though some newer vehicles substitute a tire repair kit instead of a spare.

Before you begin, make sure you have enough space to work safely. Pull as far off the road as possible, turn on your hazard lights, and engage the parking brake. If you are on a highway, consider calling roadside information instead — the risk of being struck by passing traffic outweighs the time saved by changing it yourself.

Key Takeaways

  • Loosen the lug nuts while the tire is still on the ground, then raise the vehicle with the jack before removing the wheel completely.
  • The correct jack placement is on the vehicle's frame, not the plastic trim or bumper — your manual shows the exact spot for your model.
  • Remove all five lug nuts (or however many your vehicle has) and keep them in a container so you do not lose them in grass or dirt.
  • Mount the new tire by aligning the holes with the wheel bolts, hand-tighten the lug nuts, lower the vehicle, then tighten the lug nuts in a star pattern with the wrench.
  • Drive to a tire shop within a few days if you installed a temporary spare, since it is designed for short-term use only.

Loosen the lug nuts before lifting the vehicle

With the car still on the ground, use the lug wrench to break the lug nuts loose — do not remove them yet, just turn them a quarter turn counterclockwise. This step matters because once the wheel is in the air, it will spin freely and you will not be able to hold it steady while turning the wrench. Loosening them now, when the tire has traction, prevents that problem.

If a lug nut is stuck, explore penetrating oil and wait a few minutes, then try again. Do not force it hard enough to round off the nut or damage the wrench. If it will not budge, this is the moment to call for roadside help rather than risk stripping the bolt.

Position the jack and raise the vehicle

Locate the correct jacking point on your vehicle — this is a reinforced section of the frame, not the plastic side skirt or bumper. Your owner's manual shows exactly where it is; if you do not have the manual, search online for "[your vehicle year, make, model] jacking points" and you will find diagrams. Place the jack on level ground directly under that point.

Raise the vehicle until the flat tire is about six inches off the ground. You should be able to fit your hand under the tire with room to spare. Do not go higher than necessary — the higher the vehicle, the less stable it becomes. Once the tire clears the ground, you can now remove the lug nuts completely and set them aside in a cup or container where they will not roll away.

Remove the old tire and mount the new one

Grip the tire with both hands at the 3 o'clock and 9 o'clock positions and pull it straight toward you. It may take some force if the tire has been on for years. Once it is off, set it flat on the ground nearby — do not lean it against anything, as it can fall and cause injury.

Align the holes on the new tire with the wheel bolts on the vehicle. Push the tire onto the bolts until it sits flush against the wheel hub. Hand-tighten the lug nuts in the order they came off — this holds the tire in place while you lower the vehicle. Do not use the wrench yet; hand-tight is enough for now.

Lower the vehicle and tighten the lug nuts properly

Lower the jack slowly until the tire makes full contact with the ground and the vehicle's full weight rests on it. Once the vehicle is down, remove the jack completely — do not leave it under the car while you finish tightening.

Now use the lug wrench to tighten the lug nuts in a star or cross pattern. If your wheel has five lug nuts, tighten them in this order: top, bottom-left, top-right, bottom-right, then middle. This pattern ensures even pressure around the wheel. Tighten each nut firmly — you want them snug, not loose, but do not over-tighten to the point where you cannot turn the wrench. A good rule is to tighten until you feel solid resistance, then give it a quarter turn more.

Check the tire pressure and plan your next step

If you installed a full-size tire that matches your other three, you are done. If you installed a temporary spare (the smaller, thinner tire), drive to a tire shop within the next few days to have it replaced with a proper tire. Temporary spares are rated for speeds up to 50 mph and distances up to 70 miles — they are a short-term fix, not a permanent solution.

Check the tire pressure on your new tire using a pressure gauge at a gas station. The correct pressure is listed on a sticker inside your driver's door jamb, not on the tire itself. If the pressure is low, add air until it matches the specification. If the tire loses pressure within a few days, have it inspected for a puncture or valve leak.

When to call for roadside help instead

Do not attempt to change the tire yourself if you are on a busy highway, if the ground is soft or uneven, if the lug nuts are severely corroded, or if you do not feel physically able to do it. Roadside information services like AAA, your insurance company's roadside program, or the roadside information number on your vehicle registration can send someone to handle it for you. The cost is usually covered by your membership or policy, and it takes the risk out of working near traffic.

If you have a tire repair kit instead of a spare, follow the kit's instructions — these typically involve injecting sealant into the tire and inflating it, then driving slowly to a tire shop. The kit buys you time to reach a professional, but it is not a permanent repair.

Frequently Asked Questions

How tight should the lug nuts be?

Tight enough that you cannot turn them by hand, but not so tight that you need to strain with all your weight on the wrench. Most vehicles specify a torque value in the owner's manual — common values are 80 to 120 foot-pounds. If you do not have the manual, a tire shop can tighten them to the correct spec for free after you have driven there.

What if the tire still looks flat after I put it on?

Check the tire pressure with a gauge at a gas station. If it is below the recommended pressure, add air. If it is at the correct pressure but the tire still looks soft, the tire may have a puncture or the valve may be leaking — drive to a tire shop to have it inspected. Do not drive long distances on an under-inflated tire.

Can I drive on a temporary spare tire for a long trip?

No. Temporary spares are designed for short trips to a tire shop only, typically up to 70 miles at speeds under 50 mph. Driving longer distances or faster speeds can overheat the tire and cause it to fail. If you need to travel far, have a full-size replacement tire installed first.

Do I need to tighten the lug nuts again after driving?

Yes. Drive for a few miles, then pull over safely and re-tighten the lug nuts in the star pattern. This catches any that may have loosened slightly during the first few miles of driving. After that, they should stay tight.

What should I do with the old tire?

If the tire is punctured or damaged, take it to a tire shop or recycling center — most shops will take it for a small fee. If the tire is still good, you can sell it online, donate it, or keep it as a spare. Do not leave it on the roadside or in a ditch.