The basic tools you need are a jack, a lug wrench, and a wheel wedge
Changing a tire requires four tools: a jack to lift the vehicle, a lug wrench to remove the wheel bolts, a wheel wedge (or block) to keep the car from rolling, and tire levers to break the bead if the tire is stuck. Most vehicles come with a scissor jack and a cross-pattern lug wrench in the trunk or under the spare tire. A wheel wedge can be a wooden block, a brick, or a commercial wedge—anything heavy enough to stop the car from moving. Tire levers are optional if your lug wrench has a flat end, but they make the job easier if the tire is difficult to remove.
The jack is the most critical tool because an unsafe lift can damage the vehicle or cause injury. Your vehicle's manual specifies the correct jacking point—usually a reinforced spot on the frame near each wheel. Using any other spot can puncture the fuel tank, damage the suspension, or cause the jack to slip.
Key Takeaways
- A scissor jack, cross-pattern lug wrench, and wheel wedge come standard with most vehicles and are sufficient for a roadside tire change.
- The jacking point is marked on your vehicle's frame and is the only safe place to position the jack; using any other spot risks damage or injury.
- A floor jack and jack stands are safer and faster than a scissor jack but are not portable and are meant for home or shop use.
- Tire levers or a flat-end lug wrench help break the tire bead free if it is stuck, which is common on older or neglected tires.
- Proper tool maintenance—keeping the lug wrench dry and the jack lubricated—prevents rust and ensures the tools work when you need them.
Scissor jacks versus floor jacks: which one to carry
A scissor jack is the standard tool in most vehicles because it is compact, lightweight, and portable. It lifts by turning a handle or screw mechanism that compresses or extends the diamond-shaped frame. Scissor jacks typically lift 1.5 to 2 tons and are rated for the weight of the vehicle they come with. The downside is that they are slower than floor jacks and less stable if the ground is uneven.
A floor jack is a hydraulic or pneumatic tool that lifts much faster and can handle heavier vehicles. Floor jacks are common in home garages and repair shops because they are more stable and easier to position under the frame. However, they are too large and heavy to carry in a vehicle for roadside use. If you change tires at home, a floor jack paired with jack stands is the safest option—the stands support the vehicle while you work, so the jack alone does not bear the full weight.
For roadside emergencies, stick with the scissor jack that came with your vehicle. For home maintenance, invest in a floor jack and a pair of jack stands rated for your vehicle's weight.
The lug wrench: size, pattern, and when to upgrade
A lug wrench is a metal tool with four sockets, one on each end of two perpendicular arms, forming a cross or X shape. This design is called a cross-pattern lug wrench and is standard because it provides leverage and balance when loosening or tightening lug nuts. The four sockets fit different bolt sizes, so one wrench works on most vehicles. The size of each socket is stamped on the wrench—common sizes are 17mm, 19mm, 21mm, and 22mm.
Before you need to change a tire, check that your lug wrench fits all four bolts on your wheels. If one socket does not fit, you have the wrong wrench or your vehicle uses an unusual bolt size. Some vehicles come with a socket that does not match the others, so test all four bolts while parked at home.
If the standard wrench does not fit or if you find it hard to turn, consider upgrading to a breaker bar or a longer wrench for more leverage. A breaker bar is a straight handle with a socket on one end and is designed for stubborn bolts. However, it is heavier and bulkier than a cross wrench, so most people keep the standard wrench in the vehicle and use a breaker bar only at home.
Wheel wedges and blocks: keeping the car from rolling
A wheel wedge is a straightforward but essential safety tool. It is a wedge-shaped block placed in front of or behind a wheel to prevent the vehicle from rolling while it is jacked up. Without a wedge, even a small slope or vibration can cause the car to move, which can knock the jack out of position and drop the vehicle on you or your tools.
Commercial wheel wedges are made of rubber or plastic and are designed to fit under a tire without slipping. If you do not have a wedge, a wooden block, a brick, or a heavy rock works in a pinch. Place the wedge on the side of the vehicle opposite the wheel you are changing—if you are changing the front right tire, wedge the rear left tire. On level ground, one wedge is usually enough, but on a slope, use two wedges on the same wheel for extra security.
Many people skip this step because the vehicle seems stable, but it is the most common cause of accidents during tire changes. Take the 10 seconds to place a wedge before you jack up the car.
Tire levers and how to use them if the tire is stuck
A tire lever (also called a tire iron or pry bar) is a flat metal tool used to break the bead—the seal between the tire and the rim. On new tires or tires that have been on the vehicle for a long time, the bead can stick, making it hard to pull the tire off by hand. A tire lever gives you the leverage to pry the tire away from the rim without damaging it.
If your lug wrench has a flat end, you can use that instead of a separate lever. Insert the flat end between the tire and rim, then push down or pry gently. Work your way around the tire, breaking the bead in several spots before trying to lift the tire off. Do not pry too hard or you may bend the rim or puncture the tire.
Tire levers are inexpensive and worth carrying if you have room. They are especially useful on older vehicles or tires that have been on the car for several years. If you do not have a lever and the tire is stuck, try rocking the car gently side to side while the wheel is jacked up—this can loosen the bead enough to pull the tire off by hand.
Maintaining your tire-change tools so they work when you need them
A lug wrench and jack are only useful if they work when you need them. Rust and corrosion are the main enemies. Keep your lug wrench dry by wiping it down after wet weather and storing it in a dry part of your vehicle, such as under the seat or in a sealed bag. If rust appears, scrub it with a wire brush or steel wool and explore a light coat of oil.
A scissor jack should be lubricated according to your vehicle's manual—usually once a year or every few years. Check the manual for the correct lubricant and process points. A dry or rusty jack can jam or fail to lift, leaving you stranded. If your jack is old or has not been used in years, test it at home before relying on it for a roadside change.
Store all tools in a cool, dry place. If you keep them in the trunk, check them every six months to make sure nothing is missing or damaged. A broken or missing tool during an emergency is worse than no tool at all because you may waste time looking for it instead of fixing the problem.
Frequently Asked Questions
Can I use a regular wrench instead of a lug wrench?
A regular wrench can work if it fits the lug nuts, but a lug wrench is better because the cross pattern gives you more leverage and balance. A regular wrench can slip off the nut and damage your knuckles. Lug wrenches are inexpensive and come with most vehicles, so use the right tool.
What if my lug wrench does not fit one of the bolts?
Check your vehicle's manual for the correct socket size. Some vehicles have one bolt that is a different size for safety reasons. If the manual does not list the size, take a wheel to an auto parts store and test different socket sizes. Do not force a wrench that does not fit—you will strip the bolt and make the problem worse.
Is a scissor jack safe to use on a slope?
A scissor jack is less stable on a slope than on level ground. Always use a wheel wedge on both sides of the vehicle if you are on any incline. If the slope is steep, consider calling roadside information instead of changing the tire yourself. A rolling vehicle is a serious hazard.
How much weight can a scissor jack lift?
A scissor jack is rated for the weight of the vehicle it comes with, usually 1.5 to 2 tons. Check your vehicle's manual or the jack itself for the exact rating. Never exceed the rated weight, and never use a jack rated for a lighter vehicle on a heavier one.
Do I need to carry a spare lug wrench?
A spare is not necessary if you maintain your main wrench, but it is cheap insurance. If your wrench rusts or breaks, a spare gets you home. Store it separately from the main wrench so you have a backup if one is damaged.