What a load range tells you about a trailer tire
A load range is a letter (A through F, most commonly) stamped on the sidewall of a trailer tire that tells you the maximum weight that single tire can safely carry at full air pressure. It is not about the trailer's total weight — it is about how much load one tire bears. A trailer with four tires rated Load Range D can carry more total weight than a trailer with four tires rated Load Range C, because each D-rated tire handles more.
The load range exists because trailer tires come in different construction strengths. A Load Range C tire has fewer internal plies (layers of reinforcing material) than a Load Range D, so it flexes more under weight and generates more heat. That means it cannot safely carry as much. The load range is printed right on the tire sidewall next to the tire size, so you can check it without a chart — but understanding what the numbers mean helps you buy the right replacement or spot a mismatch.
Load range is separate from tire size. Two tires can be the same size — say, 14-inch diameter — but have different load ranges and therefore different weight capacities. That is why checking the sidewall matters: size alone does not tell you what the tire can handle.
Key Takeaways
- Load range is a single letter (A through F) printed on the tire sidewall that shows the maximum weight one tire can carry at full pressure.
- Higher letters mean stronger construction and higher weight capacity — a Load Range E tire carries more than a Load Range D at the same size.
- Your trailer's tire placard (usually on the frame or tongue) lists the correct load range and pressure for your specific model.
- Replacing a tire with a lower load range than the original can cause overheating, blowouts, and unsafe towing.
- Load range and tire size are independent — two tires can be the same size but have different load ranges and capacities.
How load range letters correspond to weight capacity
Load range letters run from A (lightest duty) through F (heaviest duty). Each step up represents a real increase in how much weight one tire can handle. The jump is not the same between every letter — the gap between A and B is smaller than the gap between D and E — but the direction is always the same: higher letter, higher capacity.
The actual weight capacity depends on both the load range and the tire size. A 13-inch Load Range C tire and a 15-inch Load Range C tire have different maximum weights because the larger tire has a bigger contact patch. That is why you cannot just memorize one number. You need to know both the size and the load range, then cross-reference them on a chart specific to that tire brand and model, or check the tire manufacturer's website.
Most utility and boat trailers use Load Range C or D. Enclosed cargo trailers and heavier equipment trailers often use Load Range D or E. Tandem-axle trailers and commercial haulers may use Load Range E or F. If you are replacing a tire, match the load range on the old tire — do not guess or assume a "stronger" tire is always the right choice.
Reading the tire sidewall to find load range
The load range letter appears on the sidewall in a specific location. After the tire size (for example, ST205/75R15), you will see a space and then a two-letter code. The first letter is almost always "L" (for Load Range), and the second letter is the actual range — C, D, E, or F. So you might see "LT205/75R15 LRD" or "ST225/75R15 LRC". The "L" stands for Load Range; the letter after it is what matters.
Some older tires or certain brands may use a different format, but the load range letter is always there. If you cannot find it on the sidewall you are looking at, check the opposite side of the tire — it is printed on both sides. The letter is usually printed in a size that stands out from the rest of the sidewall text, often in a box or with extra spacing around it.
Write down the tire size and load range before you shop for a replacement. Bring a photo of the sidewall to the tire shop if you are unsure. A tire professional can also read it for you and confirm whether a replacement matches your trailer's requirements.
Why your trailer's placard matters more than a generic chart
Your trailer has a tire placard — a metal or plastic label usually bolted to the frame near the hitch or on the tongue — that lists the correct tire size and load range for that specific trailer model. This placard is the source of truth for your trailer. It was set by the manufacturer based on the trailer's weight, axle rating, and suspension design. Do not ignore it in favor of a generic load range chart.
The placard tells you the minimum load range required, the correct tire pressure, and sometimes the maximum tire size. If your placard says Load Range D at 65 psi, that is what the trailer was designed for. Putting on a Load Range C tire to save money creates a safety problem: the tire will overheat more easily, wear faster, and is more likely to fail under a full load or on a hot day.
If your trailer does not have a placard or it is illegible, contact the trailer manufacturer with your trailer's VIN or model number. They can tell you the correct specification. Do not rely on what the previous owner used or what you think might work.
Common load range combinations for different trailer types
Utility trailers (single axle, under 3,500 pounds) typically use Load Range C or D tires in sizes like ST205/75R15 or ST225/75R15. Boat trailers often fall into this category as well. Load Range C is common on older or lighter trailers; Load Range D is standard on newer models and heavier single-axle trailers.
Enclosed cargo trailers and tandem-axle utility trailers usually require Load Range D or E. The extra load range accounts for the higher total weight and the fact that weight is distributed across more tires. A tandem-axle trailer with four tires rated Load Range E can safely carry much more than a single-axle trailer with two Load Range D tires.
Specialty trailers — gooseneck, equipment, car haulers — vary widely. Some use Load Range E or F. The only way to know for certain is to check your trailer's placard or contact the manufacturer. Guessing wrong is not worth the risk of a blowout or fire while towing.
What happens when you use the wrong load range
Using a tire with a lower load range than specified creates several problems. The tire flexes more under load, which generates excess heat inside the tire. On a long drive or a hot day, that heat can cause the tire to fail — either a slow leak or a sudden blowout. The tire will also wear unevenly and fail sooner than a correctly rated tire would.
Using a tire with a higher load range than specified is generally safe from a weight perspective, but it may not fit your rim or may require different air pressure. Some trailers have rims that are not designed for the stiffer sidewall of a higher load range tire. Check with the tire shop or manufacturer before upgrading.
Mixing load ranges on the same trailer is also risky. If two tires are Load Range D and two are Load Range C, the C-rated tires will carry more of the load and fail first. Keep all four tires (or all tires on the same axle) at the same load range and size.
How to use a load range chart when comparing tires
A load range chart shows the maximum weight capacity for a specific tire size at each load range. To use one, find your tire size in the left column, then read across to the column for your load range. The number in that cell is the maximum weight one tire can carry at the manufacturer's recommended pressure.
Charts vary by tire brand and model, so use the chart from the tire manufacturer whose tire you are considering, not a generic chart. Tire shops can also print out the chart for the specific tire you are looking at. If you are comparing two different brands, get a chart from each manufacturer — the numbers may differ slightly.
Multiply the single-tire capacity by the number of tires on your trailer to understand the total weight capacity. A trailer with four tires rated 1,500 pounds each can carry 6,000 pounds total (before accounting for the trailer's own weight). Subtract the trailer's dry weight to find how much cargo you can safely load.
Frequently Asked Questions
Can I put a Load Range D tire on a trailer that came with Load Range C?
Yes, upgrading to a higher load range is generally safe and is often done on older trailers. The tire will handle more weight and run cooler. Check your trailer's placard and rim specifications first — some older rims may not be designed for the stiffer sidewall of a higher load range tire. A tire shop can confirm compatibility.
What does the number after the load range letter mean?
There is usually no number after the load range letter on the sidewall. The load range is just the letter (C, D, E, or F). If you see a number elsewhere on the sidewall, it is likely the load index or ply rating, which are different specifications. Stick with the load range letter when shopping for a replacement.
My trailer placard is missing. How do I find the correct load range?
Contact the trailer manufacturer with your trailer's VIN or model number — they can provide the original specification. You can also check the current tires on your trailer; if they are original or have been replaced correctly, the load range on the sidewall is what your trailer needs. A tire shop can also help you identify the correct size and range based on your trailer's axle rating and weight.
Do I need the same load range on both axles of a tandem trailer?
Yes, all tires on a tandem-axle trailer should be the same size and load range. Mixing load ranges or sizes can cause uneven weight distribution and tire failure. If you are replacing tires on one axle, replace all four tires at the same time to keep them matched.
Is a higher load range tire always heavier and harder to tow?
A higher load range tire is slightly heavier and has a stiffer sidewall, but the difference in towing effort is minimal and usually not noticeable. The benefit of a higher load range — better heat resistance and longer tire life — outweighs any small increase in rolling resistance. If your trailer needs Load Range D, do not downgrade to Load Range C to save weight.