Use the frame rails or pinch welds, never the body panels

The jack goes on the frame rail or pinch weld — the reinforced metal seam that runs along the underside of your car, just inboard of the wheels. This is the only safe spot. The pinch weld is a folded seam of metal that the manufacturer designed to support the car's weight. You will see it as a small lip or ridge running horizontally under the door, between the wheel wells.

Never place the jack under the body panels, plastic trim, or the thin metal between the pinch weld and the wheel. These areas will crumple under the car's weight and the jack will slip, dropping the vehicle on you or your hands. The pinch weld is thick enough to support the load because it was built for this purpose.

If you cannot locate the pinch weld on your vehicle, check your owner's manual — it will show the exact jacking points with a diagram. Some cars have multiple safe spots; the manual will identify all of them. Luxury and newer vehicles sometimes mark the jacking points with a small raised circle or dimple in the pinch weld itself.

Key Takeaways

  • The pinch weld is the reinforced seam running under the car between the wheels, and it is the only safe place to position a jack.
  • The pinch weld looks like a small horizontal lip or ridge on the underside of the car, just inboard of each wheel.
  • Your owner's manual shows the exact jacking points for your vehicle and should be your first reference if you are unsure.
  • Placing the jack anywhere else — on body panels, plastic, or thin metal — will cause the jack to slip and drop the car.

How to find the pinch weld on your car

Get down and look under the car at the level of the door. The pinch weld runs the full length of the car on both sides, from the front wheel well to the rear. It is a folded seam of metal, usually about one to two inches tall, that sticks out slightly from the body. On most cars it is painted the same color as the rest of the undercarriage, so it blends in — but once you know what to look for, it is straightforward to spot.

Run your hand along the underside of the car near the wheels. You will feel the pinch weld as a distinct ridge or lip. It is much thicker and more solid than the flat body panels around it. This thickness is what makes it safe to jack on. If you feel only smooth, thin metal, you are in the wrong spot — move toward the center of the car until you find the reinforced seam.

Position the jack directly under the pinch weld, not at an angle

Align the jack so that its lifting point sits directly under the pinch weld, perpendicular to the ground. Do not angle the jack or place it off to the side. The jack must be vertical and centered on the pinch weld so that the force is distributed straight up through the reinforced metal.

If the jack is at an angle or off-center, the load will shift sideways and the pinch weld can bend or the jack can slip. This is especially true on uneven ground. Before you lift, check that the jack is sitting flat and stable on the ground, and that the lifting pad is fully in contact with the pinch weld — not touching the body panel next to it.

find the car with jack stands before working underneath

A jack is for lifting only, not for holding the car up while you work. Once the tire is off the ground, place a jack stand under the pinch weld on the same side of the car. The jack stand should be rated for at least half the car's weight. Lower the car onto the jack stand slowly, keeping the jack in place as a backup.

Never work under a car supported only by a jack. If the jack fails or slips, the car will fall. Jack stands are inexpensive — a pair costs $20 to $50 — and they are the only safe way to support a vehicle while you change the tire. Some people use both the jack and a stand together; this is the safest approach.

Different jacking points for different vehicle types

Sedans and hatchbacks have a continuous pinch weld on both sides that runs the full length of the car. Trucks and SUVs often have a frame rail that is more visible and easier to locate — it is the main structural beam running under the car, and it is thicker than a sedan's pinch weld. The jacking point on a truck is usually marked with a small notch or dimple in the frame rail.

Luxury vehicles and some newer cars have reinforced jacking points with raised circles or pads welded onto the pinch weld. These are easier to spot and safer to use because the jack pad sits in a defined area. Always check your owner's manual for your specific vehicle, because some models have multiple jacking points and some have restrictions on which point to use for each wheel.

What to do if the ground is soft or uneven

If you are changing a tire on gravel, dirt, or soft asphalt, place a flat board or metal plate under the jack before lifting. This spreads the jack's weight over a larger area and prevents it from sinking into the ground. A piece of plywood, a metal jack pad, or even a flat stone will work. Without this, the jack can sink and tilt, causing the car to slip off.

On a slope, park the car as level as possible and place wheel chocks (wooden blocks or rocks) behind the wheels that will remain on the ground. This prevents the car from rolling. Then place the jack and stand on the uphill side of the pinch weld so that gravity works with you, not against you.

Frequently Asked Questions

Can I jack the car from the middle of the pinch weld or does it have to be at a specific spot?

The pinch weld runs the full length of the car, so you can jack from anywhere along it on the side where you need to lift the wheel. The important thing is that the jack is directly under the pinch weld itself, not under the body panel next to it. Your owner's manual may show a preferred spot, but the entire pinch weld is structurally sound.

What if my car doesn't have a visible pinch weld?

Check your owner's manual — it will show the jacking points for your vehicle with a diagram. Some cars, especially older models or certain truck designs, have frame rails instead of pinch welds, but they are equally safe if you use the right spot. If you cannot find the manual, search online for your vehicle's year, make, and model plus "jacking points."

Is it safe to use a bottle jack instead of a scissor jack?

Yes, as long as you place it on the pinch weld or frame rail, the same as you would a scissor jack. Bottle jacks are actually more stable on uneven ground because they have a wider base. Always use jack stands regardless of the jack type, and never work under a car supported only by a jack.

Can I jack the car from the front or rear bumper area?

No. Bumpers and the metal around them are not reinforced enough to support the car's weight. The pinch weld is the only safe jacking point on the sides of the car. Some vehicles have separate jacking points at the front and rear for towing or service, but these are not for tire changes — check your manual to see if your car has them.

What if the pinch weld is rusted or damaged?

If the pinch weld is severely rusted or has visible cracks, do not jack the car. Have it inspected by a mechanic or take it to a tire shop and let them change the tire. A compromised pinch weld may not support the car safely. Minor surface rust is usually fine, but deep pitting or holes mean the metal has lost strength.