Open the key fob by finding the slot on its edge and prying gently with a flat tool
Most Chevy key fobs split into two halves along a seam on the side or back. Look for a small slot or indentation — this is where the two plastic pieces meet. Use a flat tool like a coin, flathead screwdriver, or plastic pry tool to gently wedge into that slot and twist slightly. The fob will pop open without much force; if you're straining, you're likely in the wrong spot.
Once open, you'll see the battery sitting in a plastic holder, usually a round silver disc. Note which side faces up — the positive (+) side typically faces you. Take a photo with your phone before removing anything, so you know how to reassemble it correctly.
Key Takeaways
- Chevy key fobs open by finding the seam on the edge or back and gently prying with a flat tool like a coin or screwdriver.
- Most fobs use a CR2032 or CR2035 battery, which you can buy at any pharmacy, grocery store, or hardware store for under $5.
- Note which side of the battery faces up before you remove it, and take a photo so you can reassemble the fob correctly.
- Push the two halves back together until you hear a click, and test the fob on your vehicle before assuming it works.
Identify your battery type before you buy a replacement
Chevy key fobs use one of two common battery types: CR2032 or CR2035. The easiest way to know which one you have is to look at the battery itself once the fob is open — the part number is printed right on it. CR2032 is thinner and more common; CR2035 is slightly thicker. Both are coin-cell batteries you can find at any pharmacy, grocery store, Walmart, Target, or hardware store.
If you can't see the battery clearly or the printing is worn, check your vehicle's owner's manual. Chevy includes the battery type in the maintenance section. You can also call a Chevy dealership with your vehicle's year and model, and they'll tell you which battery your fob uses. Buying the wrong size won't hurt anything — it straightforward won't fit in the holder.
Remove the old battery and insert the new one
Once the fob is open, gently lift the battery out of its plastic holder. It should come free with minimal effort. If it's stuck, a tiny bit of plastic prying around the edge will loosen it — don't force it or you risk damaging the holder.
Before inserting the new battery, check the holder for any dirt or corrosion. If you see white or blue crusty buildup, wipe it clean with a dry cloth or a cotton swab. This buildup can prevent good contact and drain your new battery faster. Slide the new battery into the holder with the positive (+) side facing the same direction as the old one did. You should hear or feel a small click as it seats.
Close the fob and test it on your vehicle
Line up the two halves of the fob so the seam is even all the way around. Press them together firmly until you hear a click — the fob should feel solid, not loose or hollow. If it feels like it's not closing all the way, open it again and check that the battery is seated properly and nothing is blocking the seam.
Walk to your vehicle and press each button on the fob — lock, unlock, panic, trunk, or whatever buttons yours has. Watch for the lights to flash and listen for the door locks to respond. If nothing happens, open the fob again and check that the battery is facing the right direction. If the battery is correct and the fob still doesn't work, the fob itself may be damaged, and you'll need a replacement from a Chevy dealer or a third-party fob supplier.
What to do if the fob won't close or feels damaged
If the two halves won't close evenly or the seam has gaps, something is blocking the fit. Open the fob again and look for debris, a misaligned battery holder, or a bent piece of plastic. Remove any dirt or lint, and make sure the battery is sitting flat in its holder. If the plastic is cracked or bent, the fob may not seal properly, and moisture can get inside and corrode the electronics.
A cracked fob can sometimes still work for a while, but it will fail faster than a sealed one. If the damage is minor — a small crack that doesn't affect the seam — you can try using a small amount of clear epoxy or plastic adhesive to seal it. For major damage, a replacement fob is more reliable. Chevy dealerships sell OEM fobs, and aftermarket fobs from companies like LKE or Dorman are usually cheaper and work just as well.
How often you'll need to replace the battery
A Chevy key fob battery typically lasts three to four years with normal use. If you use your fob multiple times a day, the battery may drain faster. If you rarely use it, it may last longer. You'll know it's time to replace the battery when the fob stops working from a distance — you have to hold it closer to the vehicle, or some buttons stop responding before others do.
If your fob dies suddenly and you're sure the battery is fresh, the fob's circuit board may have failed. This is rare but can happen if the fob gets wet, dropped repeatedly, or exposed to extreme heat. In that case, you'll need a new fob rather than just a new battery.
Frequently Asked Questions
Can I use a different battery type if I can't find the right one?
No — using the wrong battery size won't fit in the holder, and forcing it can damage the fob. CR2032 and CR2035 are inexpensive and widely available, so buy the correct type. If your local store is out of stock, order online and it will arrive in one or two days.
What if my key fob has a physical key inside?
Many Chevy fobs have a metal key blade that slides out from the bottom or side. This doesn't affect how you open the fob — the battery compartment is still accessed the same way. Once you open the fob, the key blade stays in place and won't fall out.
Do I need to reprogram my fob after changing the battery?
No — changing the battery does not erase the fob's programming. It will work exactly as it did before, as long as the new battery is the correct type and installed with the positive side facing the right direction.
Is it safe to open the fob myself, or should I go to a dealer?
Opening the fob yourself is safe and takes less than a minute. You're not touching any electronics or circuits — just the battery. A dealer will charge you $50 to $100 for the same task, so doing it at home saves money and time.