Most key fob batteries cost $3 to $8 and take five minutes to swap yourself
You can replace a dead key fob battery without a dealer visit or special tools. The battery itself is inexpensive — usually a CR2032, CR2025, or similar coin-cell battery available at any pharmacy or hardware store. The hardest part is opening the fob case, which typically requires a flathead screwdriver or a coin to pry the two halves apart.
The entire job takes longer to find the right battery than to install it. Once you know your fob's battery type, you can stock a spare and have a working fob again in minutes.
Key Takeaways
- Most car key fobs use a CR2032 or CR2025 coin-cell battery that costs $3 to $8 at drugstores, supermarkets, or online retailers.
- Open the fob by inserting a flathead screwdriver or coin into the seam between the two plastic halves and twisting gently until they separate.
- Note which side of the battery faces up before you remove it, then insert the new battery the same way and snap the case closed.
- If your fob still does not work after a new battery, the problem is likely a corroded contact or a broken button — not the battery itself.
Finding the right battery type for your fob
The battery type is printed on the old battery itself, so the easiest way to know what to buy is to open the fob first and look. Most fobs use CR2032 (the most common), CR2025, or CR2016 — the numbers refer to the battery's diameter and thickness in millimeters.
If you want to know before opening the fob, check your owner's manual or search online for your vehicle's year, make, and model plus "key fob battery." Many manufacturers list this information on their websites. You can also call your dealership's parts department and give them your vehicle identification number (VIN) — they will tell you the exact battery type in seconds.
Buy batteries from a pharmacy, supermarket, dollar store, or online. A single CR2032 costs $3 to $8 depending on the brand and where you shop. Buying a multi-pack is cheaper per battery if you want spares on hand.
Opening the fob case without breaking it
Most fobs split into two halves along a seam that runs around the edge. Look for a small gap or line where the plastic meets. Insert a flathead screwdriver, coin, or plastic pry tool into the seam and twist gently — do not force it. The case will pop apart after a small amount of pressure.
Some fobs have a small slot instead of a seam. In that case, insert the screwdriver into the slot and twist. A few older or luxury fobs use a screw on the back; if you see one, unscrew it with a Phillips head screwdriver before trying to pry the case open.
If the case feels stuck, try a different spot along the seam. Fobs are designed to come apart, so if you are meeting real resistance, you may be in the wrong place. Once you find the right angle, the halves separate easily.
Removing and replacing the battery
Once the case is open, you will see the battery sitting in a small metal holder or slot. Before you touch it, look at which side is facing up — the positive (+) side or the negative (−) side. This matters because the battery must go back in the same way.
Use your fingernail or a plastic tool to gently pry the battery out of its holder. Do not use a metal screwdriver, which can scratch the battery or the contacts. Once the old battery is out, insert the new one with the same side facing up. It should sit flat in the holder and click slightly when it is seated correctly.
If the battery does not sit flat or feels loose, you may have it upside down. Flip it and try again. Once it is in place, snap the two halves of the case back together until you hear a click.
Testing the fob and troubleshooting a fob that still does not work
Press each button on the fob and listen for a click or feel for a slight vibration in your hand. If the fob works, you are done. If it does not, try these steps in order.
First, open the fob again and check that the battery is seated correctly and facing the right direction. Second, look at the metal contacts inside the fob case — they should be shiny and clean. If they are dark, corroded, or have a white or green coating, clean them gently with a pencil eraser or a cotton swab dipped in rubbing alcohol. Let them dry for a few minutes before reassembling.
Third, check that the rubber button pad is still attached to the inside of the fob case. If it has fallen out or shifted, reseat it so the rubber buttons line up with the circuit board underneath. If the buttons feel mushy or do not click, the rubber pad may be worn out and need replacement — this is a $10 to $20 repair at a dealership or electronics shop.
If the fob still does not work after these steps, the circuit board itself may be damaged. This is less common and usually requires a replacement fob rather than a repair.
When to replace the whole fob instead of just the battery
If your fob is physically damaged — cracked case, broken buttons, water damage — replacing just the battery will not help. A new fob costs $50 to $400 depending on your vehicle, with luxury cars and newer models at the higher end. Some dealerships charge extra for programming the fob to your car.
You can also buy aftermarket fobs online for $20 to $100, though you will need to program them yourself or pay a locksmith to do it. Programming usually takes 10 to 15 minutes and costs $50 to $150 if you go to a dealership or locksmith. Some vehicles allow you to program a fob yourself by turning the key in the ignition a certain number of times — check your owner's manual for the steps.
If your fob is working but the battery dies frequently — every few months instead of every few years — the problem is usually a stuck button that is draining the battery. Check that all buttons move freely and are not stuck in the pressed position.
Keeping your fob battery healthy longer
Key fob batteries last two to four years with normal use. You can extend that lifespan by keeping the fob away from extreme heat, moisture, and physical damage. Do not leave it in direct sunlight on a hot dashboard, and do not drop it or sit on it.
If you do not use your car for weeks or months, remove the battery from the fob to prevent it from slowly draining. This is especially useful if you have a spare fob that sits unused. When you are ready to use the fob again, pop the battery back in and it will work when ready.
Keep the fob case clean and dry. If it gets wet, open it and let the inside dry completely before reassembling. Water on the contacts can cause corrosion and make the fob unreliable.
Frequently Asked Questions
Can I use a different battery type if I cannot find the exact one?
No. Battery types like CR2032 and CR2025 have different thicknesses, and using the wrong one can prevent the case from closing properly or cause the battery to lose contact with the metal holders. Stick with the exact type printed on your old battery.
What if I accidentally put the battery in upside down?
The fob will not work, but the battery will not be damaged. Open the case again, flip the battery, and close it. The fob should work when ready. Coin-cell batteries are designed to handle being installed backwards without harm.
Do I need to reprogram my fob after changing the battery?
No. Changing the battery does not erase the fob's programming. As soon as the new battery is in place, the fob should work exactly as it did before. If it does not, the problem is not the battery — it is likely a corroded contact or a damaged button pad.
How do I know if the battery is actually dead or if something else is wrong?
If the fob does not respond to any button press and the battery is more than two years old, the battery is almost certainly dead. If only one button works, or if the fob works intermittently, the problem is usually a stuck button or corroded contacts, not the battery.
Can I buy a universal key fob battery that works in any fob?
No. While CR2032 is the most common type, other fobs use CR2025, CR2016, or different batteries entirely. Always use the exact type specified for your fob. Buying the wrong battery wastes money and leaves you with a non-working fob.