Subaru key fob batteries last three to four years before they stop holding a charge

When your Subaru key fob stops locking or unlocking your car reliably, the battery is almost always the culprit. The battery inside is a coin-cell type—usually a CR2032 or CR2025—that costs between $3 and $8 and takes about five minutes to swap out. You do not need a dealer appointment or special tools. A flathead screwdriver or a coin is all you need to open the fob and slide the old battery out.

The fob itself is designed to come apart at a seam that runs around its edge. Once you locate that seam, you can gently pry it open, remove the battery, and replace it with a new one from any pharmacy, supermarket, or hardware store. The whole job is something any owner can do in their driveway.

Key Takeaways

  • Subaru key fob batteries are coin-cell types (usually CR2032 or CR2025) that cost $3 to $8 and last three to four years before needing replacement.
  • You can open the fob by locating the seam around its edge and gently prying it apart with a flathead screwdriver or coin—no special tools required.
  • The battery slides out of a small holder inside the fob; note which side faces up before you remove it so you can install the new one the same way.
  • After installing the new battery, snap the fob back together and test the lock and unlock buttons before you rely on it.

Identifying which battery your Subaru fob uses

Most Subaru key fobs use either a CR2032 or CR2025 battery. The easiest way to know which one is yours is to look at the old battery once you open the fob—the size is stamped right on it. If you cannot open the fob yet or want to know before you start, check your owner's manual, which lists the battery type in the key fob section.

The CR2032 is slightly thicker than the CR2025, but both are the same diameter and cost about the same. If you buy the wrong one, it will not fit properly or may not make good contact inside the holder. When you buy a replacement, bring the old battery with you or write down the exact model number so the store clerk can match it.

Opening the fob without damaging the case

The seam that holds the fob together runs horizontally around the middle of the case. Hold the fob with the buttons facing away from you and look for a thin line where the two halves meet. Slide a flathead screwdriver or the edge of a coin into that seam and gently twist or pry—do not force it, because the plastic can crack if you push too hard.

Start at one end of the seam and work your way around. Once you feel it beginning to separate, you can usually pull the two halves apart by hand. The battery holder is mounted inside one half, and you will see it when ready once the fob is open. Some Subaru fobs also have a small metal contact spring inside; if it falls out when you open the fob, note where it sits so you can put it back in the same place.

Removing and replacing the battery

The battery sits in a small plastic or metal holder with two contact points—one on top and one on the bottom. Before you remove the old battery, look at which side is facing up. The positive side (marked with a +) should face toward you or toward the top of the fob, depending on how the holder is oriented. Take a photo with your phone if you are unsure.

Gently slide the old battery out of the holder. If it is stuck, use a plastic spoon handle or a plastic card to nudge it—metal tools can scratch the contacts. Slide the new battery in the same way, making sure the positive side faces the same direction as the old one did. Press it in until it sits flush in the holder and makes contact with both points.

Reassembling the fob and testing it

Once the new battery is in place, line up the two halves of the fob and press them together firmly until you hear or feel a click. The seam should close evenly all the way around. If one side is sticking out, open it again and check that the battery holder is seated properly and that no wires or springs are caught in the seam.

After the fob is closed, stand a few feet away from your Subaru and press the lock button. You should hear the door locks engage and see the lights flash. Press unlock and confirm the locks release. If the buttons do not work, open the fob again and check that the battery is making good contact with both points. If the battery is seated correctly but the fob still does not work, the problem may be inside the fob's circuit board rather than the battery, and you will need a replacement fob from a Subaru dealer.

When to replace the fob instead of just the battery

A new battery fixes most key fob problems, but not all. If you have replaced the battery and the buttons still do not respond, or if only one button works while others do not, the circuit board inside the fob may be damaged. Water damage, a hard drop, or age can cause the internal contacts to corrode or break.

Subaru dealers sell replacement fobs that are already programmed to your car, though the cost is higher than a battery—typically $150 to $300 depending on the model year. Some independent locksmiths also program fobs and may charge less. Before you buy a new fob, confirm with the dealer or locksmith that your car's model year and trim can accept a replacement fob and what the programming process involves.

Storing spare batteries and preventing future problems

Keep a spare CR2032 or CR2025 battery in your glove box or at home so you have one on hand when your fob dies. Batteries are cheap enough that buying two or three at once makes sense. Store them in a cool, dry place—heat and moisture shorten battery life.

To extend the life of your current fob battery, avoid exposing the fob to extreme heat, direct sunlight, or moisture. Do not leave it in a hot car or carry it in a pocket where it might get wet. If your fob does get wet, open it as soon as possible, dry the battery and contacts with a soft cloth, and let the inside air-dry for a few hours before you close it again. These straightforward steps can add months to the battery's life and prevent corrosion inside the fob.

Frequently Asked Questions

Can I use a different battery type if I cannot find the exact one?

No. The CR2032 and CR2025 are different thicknesses, and using the wrong one will either not fit or will not make proper contact with the holder. Always match the exact model number on the old battery. If your store is out of stock, order online or try another location rather than substituting.

What if the fob still does not work after I put in a new battery?

First, open the fob again and confirm the battery is seated all the way in the holder and the positive side is facing the correct direction. Check that no springs or wires are pinched in the seam. If the battery is in correctly and the fob still does not work, the circuit board is likely damaged and you will need a replacement fob from a Subaru dealer or locksmith.

How often do I need to replace the key fob battery?

Most Subaru key fob batteries last three to four years with normal use. If you use the fob heavily or leave it in hot places, the battery may die sooner. Once you replace it the first time, you will have a sense of how long it lasts for your driving habits.

Is it safe to open the fob myself, or will I break something?

Opening the fob is safe if you work slowly and gently. The seam is designed to come apart, and the battery holder is not fragile. The main risk is cracking the plastic case if you pry too hard or use a sharp metal tool. Use a coin or plastic screwdriver and take your time, and you will not damage anything.

Can I program a new fob myself if the battery replacement does not work?

No. Subaru key fobs must be programmed by a dealer or a locksmith with the right equipment. You cannot program a fob yourself. If your fob is dead and needs replacement, contact a Subaru dealer or a local automotive locksmith for programming and pricing.