Tire chains go on before you need them, not during a snowstorm
Installing tire chains takes 15 to 30 minutes per pair once you know the steps, but the real work happens at home on a dry day. You thread the chain around the tire, find the side hooks or fasteners, and tighten everything so the chain sits snug against the tread without rubbing the wheel well or suspension. The chains stay on while you drive slowly through snow, then come off once you reach clear road. Most people install them on the drive wheels — the front wheels on front-wheel-drive cars, the rear wheels on rear-wheel-drive vehicles — though some chains are designed for all four.
The hardest part is not the installation itself but matching the right chain to your tire size and vehicle, then practicing at home before winter arrives. A chain that does not fit your tire will either be too loose (and rattle or fall off) or too tight (and damage the tire or wheel). You cannot safely install chains in a blizzard on the side of a highway if you have never done it before.
Key Takeaways
- Tire chains must match your tire size exactly — check your owner's manual or the sidewall of your tire to find the correct size before you buy.
- Install chains on a flat, dry surface at home first, so you know how they work before you face snow or ice on the road.
- Chains go on the drive wheels only: front wheels on front-wheel-drive cars, rear wheels on rear-wheel-drive vehicles.
- Tighten chains firmly so they do not slip or rattle, but not so tight that they pinch the tire or rub the suspension.
- Drive slowly (usually 30 mph or less) with chains on, and remove them as soon as you reach bare pavement to avoid damage to the tire and road.
Choosing the right chain size for your tires
Tire chains are sold by size, and that size must match your tire size exactly. Your tire size is printed on the sidewall of your tire in a code like 225/65R17 — the numbers refer to width, aspect ratio, and wheel diameter. Your vehicle's owner's manual also lists the correct tire size in a table, usually inside the driver's door jamb or in the back of the manual.
When you buy chains, the package will say which tire sizes it fits — for example, "fits 225/65R17 and 235/65R17". If your tire is 225/60R17, a chain marked for 225/65R17 will not fit correctly. Too loose, and the chain will rattle and slip off the tire. Too tight, and it will pinch the sidewall or rub the suspension components inside the wheel well, tearing the tire or bending brake lines.
Bring your tire size with you when you shop, or order online with the size written down. Do not guess. If you are unsure, call the retailer and read them the sidewall code — they can confirm the fit in seconds.
Laying out and threading the chain onto the tire
Before you install chains, park on a flat, level surface — a driveway or parking lot, not a slope. Turn off the engine. Lay the chain out flat on the ground next to the tire so you can see the whole thing and identify which end is which. Most chains have a master link (a larger link that closes with a pin or bolt) on one end and a hook or fastener on the other.
Drape the chain over the top of the tire so it hangs down both sides evenly. The chain should sit in the center of the tire tread, not touching the sidewall. Now work the chain around the tire by hand, threading it under and around so it wraps the tire like a belt. The goal is to have the chain sit flat against the tread with no twists or kinks.
Once the chain is threaded all the way around, the two ends will meet on the inside of the wheel (the side closest to the vehicle body). This is where you fasten them together using the master link, hooks, or bolts that came with your chain. Different chains use different fastening methods — some have a pin that slides through holes, others have a bolt and nut, and some use a quick-release lever. Follow the instructions that came with your specific chain.
Fastening and tightening the chain securely
Once the chain is threaded around the tire, fasten the ends together firmly. If your chain uses a pin-and-hole system, slide the pin through both ends and find it with the clip or cotter pin provided. If it uses a bolt, thread it through both ends and tighten it with a wrench until snug — not so tight that you strip the threads, but tight enough that the chain cannot move side to side.
After the ends are fastened, the chain will still be loose around the tire. This is normal. Now tighten the chain by pulling on the loose sections and securing any additional fasteners or tightening bolts that run along the sides of the chain. Most chains have two or four side fasteners (called binders or tighteners) that you tighten after the main connection is made. Pull the chain snug against the tire and tighten these fasteners so the chain sits firmly in the tread without any slack.
The chain should be tight enough that it does not rattle or move when you push on it, but not so tight that it pinches the tire sidewall or rubs the suspension. If you can fit more than one finger between the chain and the tire, it is too loose. If the tire bulges noticeably where the chain sits, it is too tight. Adjust until the chain is snug and even all the way around.
Installing chains on the correct wheels
On a front-wheel-drive vehicle, install chains on both front wheels. The front wheels do the steering and most of the braking, so chains there give you the most traction and control. On a rear-wheel-drive vehicle, install chains on both rear wheels — these are the wheels that push the car forward, and adding traction there prevents the rear from sliding out.
On an all-wheel-drive vehicle, you have a choice: you can install chains on the front wheels only, the rear wheels only, or all four. Check your owner's manual for the manufacturer's recommendation, as some all-wheel-drive systems are designed to work better with chains on a specific axle. If the manual does not specify, front wheels are usually the safer choice because they control steering.
Never install chains on only one side of an axle (for example, only the driver's side front wheel). This creates uneven traction and can cause the vehicle to pull to one side or lose control on slippery surfaces.
Checking the fit before you drive
Before you move the vehicle, turn the steering wheel fully left and right to make sure the chains do not rub the suspension, brake lines, or the inside of the wheel well. Spin the wheel by hand and listen for any scraping or rattling. If the chain touches anything other than the tire, stop and loosen it slightly or reposition it so it sits in the center of the tread.
Once you are satisfied with the fit, start the engine and drive forward slowly — just a few feet — then stop and check the chains again. Sometimes they settle into a different position once the vehicle is moving and the tire is under load. Tighten them again if needed.
If you are installing chains for the first time, do this test run in your driveway or an empty parking lot, not on a public road. You want to be confident the chains are find before you drive in traffic or on a highway.
Driving with chains and removing them safely
With chains installed, drive slowly — most manufacturers recommend 30 mph or less, and many states have legal speed limits of 25 to 35 mph for vehicles with chains. Chains are loud and will rattle, especially on bare pavement. They also reduce traction slightly compared to driving without them on dry roads, so they are meant only for snow, ice, or packed snow conditions.
Remove chains as soon as you reach clear, dry pavement. Driving on bare asphalt with chains on will damage both the chains and the road surface, and it is illegal in many places. To remove them, park on a flat surface, loosen all the fasteners and tighteners, and pull the chain out from under the tire. Coil it up and store it in a dry place — a garage or trunk — until the next time you need it.
Before you store chains, wipe them down with a dry cloth to remove any salt or moisture. Salt corrodes metal, so chains stored wet will rust and become brittle. If you live in a snowy climate and use chains regularly, inspect them each season for broken links, bent hooks, or rust before you install them on your vehicle.
Frequently Asked Questions
Can I install tire chains while driving or on the side of the road?
You can, but it is dangerous and difficult. Chains are meant to be installed on a flat, level surface where you have room to work and can see what you are doing. If you must install them on the roadside, turn on your hazard lights, stay as far from traffic as possible, and work quickly. This is why practicing at home first is so important — you will be much faster and safer if you already know how.
Do I need chains on all four wheels or just two?
Two wheels (both on the same axle) is the standard. Install them on the drive wheels: front wheels for front-wheel-drive, rear wheels for rear-wheel-drive. Check your owner's manual for all-wheel-drive vehicles, as some manufacturers recommend a specific axle. Never install chains on only one wheel — this causes uneven traction and loss of control.
What if my chains are too loose and rattle while I drive?
Stop as soon as it is safe and tighten them. Loose chains can slip off the tire, damage the wheel well, or break. Pull over, tighten all the fasteners and side binders, and test the fit again by spinning the wheel by hand. The chain should not move when you push on it.
Can I leave chains on while driving on dry pavement?
You should not. Chains damage the tire tread and the road surface when driven on dry asphalt, and it is illegal in many states. Remove them as soon as you reach clear pavement. If you are unsure whether the road ahead is clear, drive slowly and remove them at the first safe opportunity.
How do I know if my chains fit before I buy them?
Match the chain size to your tire size exactly. Your tire size is on the sidewall (like 225/65R17) and in your owner's manual. The chain package will list which tire sizes it fits. If you are unsure, call the retailer with your tire size and they can confirm the fit. Do not buy chains that are close — they must match your size.