Install snow chains before you hit snow, not in a blizzard on the roadside

Snow chains go on your drive wheels — the wheels that power the car forward. On a front-wheel-drive vehicle, that means the front two tires. On a rear-wheel-drive vehicle, the rear two tires. All-wheel-drive vehicles technically need chains on all four, but many states allow chains on just the drive wheels; check your state's winter tire laws before you leave home.

The installation itself takes 15 to 30 minutes per wheel once you know the steps. The real work is doing a practice run in your driveway on dry pavement before winter weather arrives. Fumbling with chains in cold, wet conditions while traffic backs up behind you is how people damage their wheels and give up on chains altogether.

You will need your owner's manual to confirm your vehicle's chain size — chains are sized by tire width and sidewall height, not by wheel diameter — and you will need to park on level ground with the engine off. Bring work gloves, a flashlight, and patience.

Key Takeaways

  • Snow chains fasten to your drive wheels only: front wheels on front-wheel-drive cars, rear wheels on rear-wheel-drive cars, and all four on all-wheel-drive vehicles (though some states allow just the drive wheels).
  • Your owner's manual lists the correct chain size by tire dimensions, not wheel size, and chains must match your specific tire width and sidewall height.
  • Practice installing chains in your driveway on dry pavement before winter so you can do it quickly and correctly in bad weather.
  • Chains should be snug enough that you cannot slide them around the tire by hand, but not so tight that they pinch the sidewall or rub the wheel well.
  • Drive slowly — usually 30 mph or less — with chains on, and remove them as soon as you reach bare pavement to avoid damage to both the chains and your tires.

Choosing the right chain size for your tires

Open your owner's manual and look for the tire specifications section. You will see a number like 225/65R17 — that is your tire size. The first number (225) is the tire width in millimeters. The second number (65) is the sidewall height as a percentage of width. The letter R means radial construction. The last number (17) is the wheel diameter in inches, which you do not need for chains.

Take the tire width and sidewall height to a tire shop or call the chain manufacturer's customer service line with those two numbers. They will tell you the correct chain size. Do not guess. A chain that is too small will not fit around the tire. A chain that is too large will be loose and can damage your wheel or fall off while driving.

Buy chains before winter arrives so you have time to practice. Most auto parts stores stock common sizes, but if your vehicle has an unusual tire size, you may need to order ahead.

Preparing your vehicle and workspace

Park on level, dry ground away from traffic. Turn off the engine and engage the parking brake. If you are practicing in your driveway, that is ideal. If you are installing chains on the road, pull as far off the shoulder as possible and turn on your hazard lights.

Lay out all your chain components on the ground so you can see what you are working with. Most chains come as two separate loops — one that wraps around the top of the tire and one that wraps around the bottom — connected by side links. Some chains are self-tightening; others require manual tightening after installation. Read the instructions that came with your chains so you know which type you have.

Put on your work gloves. Chains are sharp and will cut your hands if you are not careful. Position your flashlight so you can see the tire clearly.

Draping and fastening the chain around the tire

Start with the top loop of the chain. Drape it over the top center of the tire so the chain hangs evenly on both sides. The chain should fall naturally into the tire tread — do not force it or twist it. The side links should hang down toward the ground on both the left and right sides of the tire.

Take the left side link and bring it around the inside of the wheel, then up and over the bottom of the tire, and connect it to the right side link on the outside of the wheel. Most chains use a hook-and-link system: you will hook one end into a link on the other side. Some use a cam lever or a pin-and-clip system. Follow the instructions for your specific chain type.

Once the side links are connected, the chain should form a complete loop around the tire. Do not tighten it yet. Check that the chain is centered on the tire and not twisted. The chain should sit in the tire tread grooves, not on the rubber sidewall.

Tightening the chain to the correct tension

Tighten the chain by hand first. Pull each connection point — usually the side links or the top loop — so the chain is snug against the tire. You should not be able to slide the chain around the tire by hand, but you should still be able to fit one finger between the chain and the tire sidewall. If you can fit more than one finger, the chain is too loose. If you cannot fit any finger, the chain may be too tight and could damage the sidewall.

Some chains have a self-tightening mechanism that will snug up as you drive the first few hundred feet. If your chain has this feature, tighten it only by hand at this stage. If your chain requires manual tightening, use the tightening tool or lever that came with it — usually a small ratchet or cam lever — to bring the tension up another notch.

Drive forward slowly — about 5 to 10 mph — for 50 to 100 feet, then stop and check the tension again. Chains often settle into the tire tread after a few feet of driving. Retighten if needed. This is why practicing in your driveway is so valuable: you can work out the tension without worrying about traffic or weather.

Installing chains on the second drive wheel

Repeat the same process on the other drive wheel. Drape the top loop, connect the side links, center the chain on the tire, and tighten by hand. Then drive forward slowly and retighten. The two chains should be equally tight — if one is loose and one is tight, your vehicle will pull to one side and the loose chain may fall off.

Once both chains are installed and tightened, drive slowly for a quarter mile or so at low speed to let them settle. Stop and do a final tension check on both wheels. This is your final note to adjust before you hit the road.

Driving with chains and removing them safely

Drive slowly and smoothly with chains on. Most states have a legal speed limit of 30 mph or less when chains are installed. Accelerate gently, brake gently, and avoid sharp turns. Chains are not designed for highway speeds and will wear out quickly if you drive too fast.

Listen for any unusual noise — a clanking or rattling sound means a chain has come loose and you need to stop and retighten it when ready. Do not ignore it and hope it tightens itself.

Remove chains as soon as you reach bare pavement. Driving on dry asphalt with chains on will destroy both the chains and your tires. Pull over in a safe spot, turn off the engine, and disconnect the side links first, then the top loop. Coil the chains loosely and store them in your trunk. Do not leave chains on any longer than necessary.

Frequently Asked Questions

Can I install chains on any tire, or do I need special winter tires?

Chains work on any tire as long as the tire has enough tread depth — usually at least 4/32 of an inch. Winter tires are not required to use chains, though winter tires do provide better grip on snow and ice than all-season tires. Chains are a separate system that adds traction on top of whatever tire you have.

What if my vehicle has a tight wheel well and the chain rubs the suspension?

Some vehicles with low-profile tires or tight suspension geometry cannot fit standard chains without rubbing. If this is your situation, ask a tire shop about cable chains, which are thinner than traditional chains, or about tire socks, which are fabric sleeves that slip over the tire. Not all states allow tire socks, so check your local winter tire laws first.

Do I need to remove chains before driving on a highway?

Yes. Chains are designed for low-speed driving on snow and ice. Driving faster than 30 mph with chains on will damage the chains, your tires, and potentially your suspension. Remove chains as soon as you reach a highway or any stretch of bare pavement.

How do I know if my chains are the right size if I have already bought them?

Try to fit them on the tire in your driveway. A correctly sized chain will drape over the tire and connect without forcing or twisting. If the chain is too small, it will not reach around the tire. If it is too large, it will be loose and sloppy. If you have the wrong size, return them and order the correct size before winter weather arrives.

Can I leave chains on overnight if I park in the snow?

You can, but it is not ideal. Chains left on stationary tires can rust and weaken over time, especially if the vehicle is parked outside. If you need to leave chains on, remove them as soon as you can drive on bare pavement. Store them in a dry place indoors during the off-season.